HINKLEY 20020 Scout 1-lt 7 Inch Tall LED Outdoor Wall Mount Lantern Instruction Manual

: June 8, 2024
: HINKLEY

Table of Contents

20020 Scout 1-lt 7 Inch Tall LED Outdoor Wall Mount Lantern
Mounting Instructions
Wiring instructions
Grounding instructions
Documents / Resources

20020 Scout 1-lt 7 Inch Tall LED Outdoor Wall Mount Lantern
Instruction Manual
Item No: 20020

20020 Scout 1-lt 7 Inch Tall LED Outdoor Wall Mount Lantern

DRAWING 1 – Fixture Installation

Mounting Instructions

start here

Find a clear area in which you can work.
Unpack fixture and glass from carton.
Carefully review instructions prior to assembly.
To begin assembly remove front of fixture (F) from backplate (L) by removing screws (E)
Next remove screws (Z) from the side of of the backplate. This will release the mounting plate (A)
Use 8-32 screws (not provided) to secure mounting plate (A) to junction box (J)
Next make wiring connections using IS-18 on the next page.
Attach backplate (L) using the previously removed screws (Z).
Fixture can be lamped accordingly
Replace front cover (F) using screws (E) 8.Fixture can now be powered on

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUC-TIONS (1.5. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
Make electrical connections from supply wire to fixture lead wires. Refer to instruction sheet (1.5. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to complete installation of this fixture.
Drawing 1 — Flush Mount

Drawing 2 —- Chain Hung Drawing 3 —- Post Mount

IS. 18 wiring grounding instructions
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING I S REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE EQUIREMENTS

Wiring instructions

Indoor Fixtures

Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector – see Drawings 1 or 2 .
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector — see Drawings 2 or 3.
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
Cover open end of connectors with silicone sealant to form a watertight seal.
If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface i s lap siding, use caulk and a fixture mounting platform specially.
Please refer to the grounding instructions below to complete all electrical connections.

Grounding instructions

Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) – see Drawing 1.
Note: On straps for screw supported fixtures , first install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2 .
Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – see Drawing 3.

HINKLEY 33000Pin OakParkway,
Av onLake,
OH44012 800.446.5539/440.653.5500
hinkley.com

Documents / Resources

| HINKLEY 20020 Scout 1-lt 7 Inch Tall LED Outdoor Wall Mount Lantern [pdf] Instruction Manual
20020 Scout 1-lt 7 Inch Tall LED Outdoor Wall Mount Lantern, 20020, Scout 1-lt 7 Inch Tall LED Outdoor Wall Mount Lantern, Tall LED Outdoor Wall Mount Lantern, Wall Mount Lantern, Mount Lantern, Lantern
---|---