ZIIDOO Bluetooth 5.0 Transmitter and Receiver Instruction Guide
- June 8, 2024
- ZIIDOO
Table of Contents
ZIIDOO Bluetooth 5.0 Transmitter and Receiver
Product Overview
Working Status Indicator / Audio Mode Indicator / Connected Device Indicator / CODEC Indicator /
Pair Button / [Multi Function Button(MFB)/Charge Indicator] / Working Status Switch / Audio Mode Switch / 3.5mm Audio Port / SPDIF Input / SPDIF Input / Micro USB Charge Port
Package Contents
- Bluetooth Transmitter & Receiver *1
- 5mm Audio Cable *1
- Micro USB Charging Cable *1
- User Manual *1
- Fiber Optic Cable *1
Basic Operation
How to use as a Bluetooth Transmitter (TX)
Bluetooth pairing and connection
- Under power off status, switch to TX side and long press MFB for 3 seconds to power on (Or power on then switch to TX side).
- Short press pair button to enter pairing mode with TX LED fast flash if doesn’t enter when power on.
- Set your device (bluetooth headphone, speaker or receiver) to power on and pairing mode, with Red & Blue LED flash alternately or Blue LED fast flash.
- Place I2 and your device close and wait for 5-30 seconds. TX, “A”and CODEC LED will turn on after connected.
- Connect I2 and your phone with 3.5 mm audio cable, and could play music from your phone to the headphone or speaker.
- Setting Under power off, switch working status to TX side.
- Pairing Long press MFB for 3 seconds to power on, short press pair button to enter pairing mode with TX LED fast flash if doesn’t enter when power on. Power on the bluetooth headphone or speaker and enter pairing mode.
- Connection place I2 and your device close and wait for 5-30 seconds. TX, “A”and CODEC LED will turn on after connected.
- Audio mode switch Switch audio mode to AUX side means AUX mode, SPDIF side means SPDIF mode (TX status is SPDIF TX)
Multi Point Connection
- Follow 3.1 to connect with the first device, short press pair button to enter pairing mode with TX LED fast flash.
- Power on the second device (bluetooth headphone, speaker or receiver) and enter pairing mode. Place them close and wait 5-30 seconds, I2 will connect two device with “A”and “B”LED turn on.
Note
- Pls turn off I2 and turn on again, and try to reconnect or repair with two devices, when it could not connected with two devices at the first time.
- Multi point connection could compatible with most of the chipset solution at the market, except less of them.
- Single connection priority support aptX™ HD (connected device also support aptX™ HD). Two connections priority support aptX™ HD (connected devices also support aptX™ HD). Two connections priority support aptX™ low latency (connected devices also support aptX™ low latency). Two connections priority support aptX™ (connected devices also support aptX™). Two connections turn to SBC automatically if the CODEC are different.
TV Connection
Connect I2 and the TV with 3.5mm audio cable or fiber optic cable, and Bluetooth connect I2 with devices ( Bluetooth headphone or speaker ), and could transmit the audio from TV to the devices .
Note
- Pls test the TV with wired headphone or check the TV’s audio settings (Select 3.5mm output ) to make sure the devices connect in the right way and play audio from the TV.
- Pls connect the TV and SPDIF TX port with fiber optic cable when select the Toslink connection mode.
How to use as a Bluetooth Receiver (RX)
Bluetooth pairing and connection
- Under power off mode, switch to RX side and long press MFB for 3 seconds to power on (Or power on then switch RX side).
- Short press pair button to enter pairing mode with RX LED fast flash if doesn’t enter when power on.
- Place I2 and your phone (pc, tablet) close, turn on the bluetooth function of the phone and connect “Boltune I2”.
- TX and “A” LED turn on after connected, the speaker can be played music from phone (PC or tablet) with 3.5mm audio cable or fiber optic cable.
- Setting Under power off, switch working status to RX side.
- Pairing Long press MFB for 2 seconds to power on, short press pair button to enter pairing mode with RX LED fast flash if doesn’t enter when power on. Power on the bluetooth headphone or speaker and enter pairing mode.
- Connection Turn on the bluetooth function of the phone, search and connect “Boltune I2”. RX and “A” will turn on after connected.
- Audio mode switch Switch audio mode to AUX side means AUX mode, SPDIF side means SPDIF mode (RX status is SPDIF RX)
Multi Point Connection
- Connect the first phone (pc, tablet).
- Short press pair button to enter pairing mode with RX LED fast flash.
- Turn on the bluetooth function of the second phone, search and connect “Boltune I2”. Multi point connection is working with RX, “A” and “B” LED turn on.
Note
- Only could play music from one phone when with two connections. Need to stop the first one’s music then to play the other one’s music.
- Priority support aptX™ HD for one connection(the connected device also support aptX ™ HD), support CODEC according to the phone which playing music for two connections.
Speaker Connection
Connect I2 and Speaker with 3.5 mm audio cable or fiber optic cable, and bluetooth connect with phone (PC, laptop), play music from your phone to speaker.
Notes
- Pls test the speaker with 3.5 mm audio cable (connect phone) to see if workable, if could not play when connect with I2.
- Pls insert to SPDIF RX port for Toslink connection.
Charging
Pls charging I2 when low battery with Red LED flash. LED turn off when full charged (about 2 hours ).
Connection for charge
Connect I2 and power supply (charger , car charger , computer USB etc ) with Micro USB cable.
Notes
- Pls charge the I2 at least once every 2 months if without use.
- Pls press “MFB” and connect with power supply to reset the item, when it dead during use.
LED Indicator
Product Specification
Notes
- Working time will be different depend on different working environment and CODEC.
- Standby time will be same as working time on TX mode, as it will be working once connected.
- CODEC depend on the connected devices and follow the turns as mention.
Attention and Q & A
Power off automatically?
Without connect with any devices for more than 10 minutes the item will power off automatically in RX mode, except in TX mode.
How to reconnect?
I2 will reconnect with paired devices when power on. If not , pls follow the 3.1 or 4.1 to pair & connect again.
Password for connect?
Pls enter “0000” (four zero), “8888” (four eight), ”1111” (four one), or “1234” (one, two, three, four) for some devices which need password to connect .
Could not power on or dead when connect?
Press MFB and connect with power supply to reset the item, and repower for use.
Charging power supply?
Charging power supply: 5V, ≥500 mA. (Charger, car charger , computer USB etc).
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Frequently Asked Questions
Can I use the I2 as a Bluetooth Receiver (RX)?
Yes, you can use it as a Bluetooth Receiver.
Can I connect the SPDIF cable and Micro USB charging cable at the same time?
No, you can’t connect them at the same time. You have to disconnect one of them before connecting the other one.
What is the difference between Bluetooth 5.0 and Bluetooth 4.0?
The difference between Bluetooth 5.0 and 4.0 is that Bluetooth 5.0 supports dual-band frequency, while Bluetooth 4.0 only supports single-band frequency. In addition, Bluetooth 5.0 supports higher data rate than 4.0, which means faster transmission speed and less power consumption than 4.0.
What is the difference between I2 and I1?
The difference between I2 and I1 is that I2 supports dual-band frequency (2.4GHz/5GHz), while I1 only supports single-band frequency (2.4GHz).
Is it functional while it is charging?
Not for me, no When I use it while it’s charging, there is a loud buzzing and it only plays over one side of the headphones I use. I charge it using the USB port on my TV.
How can I connect if my TV doesn’t have a 3.5 mm port?
You can put the connection in directly if your TV has a 3.5MM interface. You might need to convert the cable if your TV lacks a 3.5MM interface.
Do these transmit to my wireless Bluetooth earphones in stereo rather than mono? I own a few different pairs, including the Powerbeats 2 and 3.
Yes, stereo broadcasts are made.
Why won’t it pair with a Bose Bluetooth speaker in tx mode?
Another possibility is that the gadget is tethering to another Bluetooth device in the same space. It will typically link with the device that is nearest to it because you cannot select the device that it chooses to pair with. To ensure that it just tries to couple with the Bose speaker, make sure all Bluetooth devices nearby are switched off.
Does anyone use this for their TCL Roku TV?
I do not suggest using it to watch television because the audio is occasionally audible and is off by a few milliseconds.
Does the microphone on Bluetooth headsets function? My phone has a jack port for audio and a microphone but no Bluetooth.
Yes, it will function in transmit mode in a phone’s ear jack.
Does the microphone on Bluetooth headsets function? My phone has a jack port for audio and a microphone but no Bluetooth.
Yes, it will function in transmit mode in a phone’s ear jack.
Will this function with two-way radios?
Some sources, I’ve learned, are reliable while others are not. One of my televisions receives the audio signal, and the other does not. It appears to be a case-by-case endeavour.
Is this compatible with portable DVD players?
Yes, it ought should work. The audio will be sent when you plug it into the headphone jack. After that, you can pair your Bluetooth headphones or earbuds. This is how I’m using it for an mp3 player.
How does it charge, and do August Bluetooth speakers work with this?
Most Bluetooth speakers will be compatible with it, and a regular micro USB cord is used for charging.
Video
ZIIDOO-Bluetooth-5.0-Transmitter-and-Receiver