HCFa TPTL 2510-E Human Machine Interface Instructions

TP(TL)2510-(E)，TP(TL)2507-(E)，TP(TL)2504-(E)
Hardware Instruction

TPTL 2510-E Human Machine Interface

Thanks for purchasing HCFA products.
This manual describes the sp ecif TP(TL)2510-(E)，TP(TL)2507-(E)，TP(TL)2504-(E) (hereinafter referred to as TP). Before use, read th is manual and manuals of relevant products fully to acquire prociency in handling and opera ting the product. Make sure to learn all the product information, safety information, and precautions.
Ective May, 2016
Specications are subject to change without notice.
Safety Precaution (Read these precautions before using.)
Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as “WARNING” and “CAUTION”.

WARNING| Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe inju.
---|---
CAUTION| Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injuysical damage.

Depending on circumstances, procedures indicated by “CAUTION” may also be linked to serious results.
In any case, it is impoollow the directions for usage.

DESIGN PRECAUTIONS

WARNING

• Some failures of the TP or cable may keep the outputs on or off.
  An external monitoring circuit should be provided to check for output signals which may lead to a serious accident.
  Not doing so can cause an accident due to false output or malfunction.

• Do not use the TP as the warning device that may cause a serious accident.
  An independent and redundant hardware or mechanical interlock is required to cone the device that displays and outputs serious warning.
  Failure to obsee this instruction may result in an accident due to incorrect output or malfunction

• When the TP detects its b acklight failure, the TP disables the input ope ration on thetouch switches. Thus, operators cannot operate the TP with touches. The TP backlightfailure can be checked with a system signal of the TP.

• Even when the display section has dimmed due to a failure of liquid cstal section or backlight on the TP, the input operation of touch switches may still be enabled. This may cause an incorrect operation of touch switches. For example, if an operator assumes that the display section has dimmed because of screen save function and touches the display section to cancel screen save, a touch switch may be activated The TP backlight failure can be checked with a system signal of the TP.

• The display section of TP is an analog-resistive type touch panel. Simultaneous pressing of two or more areas on the display section may activate the switch between those areas. Do not press two or more areas simultaneously on the display sec tion.
  Doing so may cause an accident due to incorrect output or malfunction.

• When the programs and parameters of controller (such as a PLC) that is monitored by a TP are changed, be sure to shut ower of the TP promptly and power on the TP again. Not doing so can cause an accident due to false output or malfunction.

• If a communication fault (including cable disconnec tion) occurs during monitoring on the TP, communication between the TP and PLC CPU is suspended and the TP becomes inoperative. A system where the TP is used should be congured to peorm any si gniation to the system by using the switches of a device other than the TP on the assumption that a TP communication fault will occur.
  Not doing so can cause an accident due to false output or malfunction.

CAUTION

• Do not bundle the control and communication cables with main-circuit, power or other wiring.
  Run the above cables separately from such wiring and keep them a minimum of 100mm (3.94in.) apa. Not doing so noise can cause a malfunction.

• Do not press the TP display section with a pointed material as a pen or driv er. Doing so can result in a damage or failure of the display section.

• When the TP is connected to Ethernet network, the available IP address is restricted according to the system conation.
  – When multiple TPs are connected to the Ethernet network: Do not set the IP address (192.168.0.200) for the TPs and controllers in the network.
  – When a single TP is connected to the Ethernet network: Do not set the IP address (192.168.0.200) for the controllers except the TP in the network.

• Doing so can cause the IP address duplication. The duplication can negatively aect the communication of the device with the IP address (192.168.0.200). The operation
  of IP address duplication depends on the devices and system.

• Turn on the controller and network device to be ready for communication before they communicate with the TP. Failure to do so can cause a communication error on the TP.

• When the TP is subject to shock and vibration, or some color appear on the screen of the TP, the screen of TP might flicker.

MOUNTING PRECAUTIONS

WARNING

• Be sure to shut oll phases of the external power supply used by the system before mounting or removing the TP to/from the panel.
  Not doing so can cause the unit to fail or malfunction.

CAUTION

• Use the TP in the environment that satiss the general speciscribed in this manual.
  Not doing so can cause an electric shock, e, malfunction or product damage or deterioration.

• When mounting the TP to the control panel, tighten the mounting screws in the speci torque range(0.36N·m to 0.48 N·m). Undeening can cause the TP to drop, shocuit or malfunction. Oveightening can cause a drop, shoircuit or malfunction due to the damage of the screws or the TP.

• Remove the protective lm of the TP. When the user continues using the TP with the protective y not be removed.

• Operate and store the TP in environment without direct sunlight, high temperature, dust, humidity and vibration.

• Do not use the TP in an environment with oil or chemical. Doing so can cause failure or malfunction due to the oil or chemical entering into the TP.

WIRING PRECAUTIONS

WARNING

• Be sure to shut os of the external power supply used by the system before wiring.
  Failure to do so may result in an electric shock, product damage or malfunctions.

CAUTION

• Please make sure to ground FG terminal of the TP power supply section. Not doing so may cause an electric shock or malfunction.
• Correctly wire the TP power supply section after conated voltage and terminal arrangement of the product. Not doing so can cause a e or failure.
• Tighten the terminal screws of the TP power supply section in the specied torque range (0.5N·m to 0.6 N·m). Undecuit or malfunction. Oveightening can cause a shocuit or malfunction due to the damage of the screws or the TP.
• Ensure to avoid foreign matter such as chips and wire ocuts entering the TP. Not doing so can cause a e, failure or malfunction.
• Plug the communication cable into the TP inteace or the connector of the connected unit, and tighten the mounting screws and the terminal screws in the specied torque range.
  Undeening can cause a shocuit or malfunction. Ove circuit or malfunction due to the damage of the screws or the TP.

TEST OPERATION PRECAUTIONS

WARNING

• Before peorming the test operation of the user creation monitor screen (such as turning ON or OFF bit device, changing the word device current value, changing the settings or current values of the timer or counter), read through the manual carefully and make yourself familiar with the operation method.
  During test operation, never change the data of the devices which are used to perm signiation for the system. False output or malfunction can cause an accident.

STARTUP/MAINTENANCE PRECAUTIONS

WARNING

• When power is on, do not touch the terminals.
  Doing so can cause an electric shock or malfunction.

• Before sta externally in all phases. Not switching the power off malfunction. Unde cause a sho circuit or malfunction due to the damage of the screws or unit.

CAUTION

• Do not disassemble or modify the unit.
  Doing so can cause a failure, malfunction, injue.

• Do not touch the conductive and electronic paf the unit directly.
  Doing so can cause a unit malfunction or failure.

• The cables connected to the unit must be run in ducts or clamped.
  Not doing so can cause the unit or cable to be damaged due to the dangling, motion or accidental pulling of the cables or can cause a malfunction due to a cable connection fault.

• When unplugging the cable connected to the unit, do not hold and pull the cable portion.
  Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault.

• Do not drop or apply any impact to the batte.
  If any impact has been applied, discard the batteer use it.
  The battey be damaged by the drop or impact.

• Before touching the unit, always touch grounded metal, etc. to discharge static electricity from human body, etc.
  Not doing so can cause the unit to fail malfunction.

TOUCH PANEL PRECAUTIONS

CAUTION

• For the analog-resistive lm type touch panel, normally the adjustment is not required.
  However, the dierence between a touched position and the objec t position may occur as the period of use elapses. When any dierence between a touched position and the object position occurs, execute the touch panel calibration.

• When any dierences between a touched position and the object position occurs, other object may be activated. This may cause unexpected operation due to incorrect output or malfunction.

PRECAUTIONS WHEN THE DATA STORAGE IS IN USE

WARNING

• If the SD card mounted on the drive A of the TP is removed while the TP is accessed, processing for the TP might be interrupted for about 20 seconds. The TP cannot be operated during this period. The functions that run in the background including a screen updating, alarm, logging, scripts and other are interrupted. Since this interruption makes an impact to the system operation, it might cause failure. After inhibiting the access to SD card on the TP utility screen, check that the SD card access LED is oemove the SD card.

CAUTION

• If the data storage mounted on the TP is removed while the TP is accessed, the data storage and e damaged. To remove the data storage from the TP, check that the access to data storage in SD card access LED, the system signal and others are not peormed.
• When removing SD card from the TP, make sure to suppohe SD card by hand as it may pop out. Failure to do so may cause the SD card to drop from the TP, resulting in a failure or break.
• Before removing USB device from the TP, follow the procedure for removal on the utility screen of the TP. After the successful completion dialog is displayed, remove the USB device by hand carefully. Failure to do so may cause the USB device to drop from the TP, resulting in a failure or break.

DISPOSAL PRECAUTIONS

CAUTION

• When disposing this product, treat it as industrial waste.

TRANSPORATION PRECAUTIONS

CAUTION

• Before transpoTP, turn the TP power on and check that the batteoltage status is normal on the Time setting & display screen (utilities screen). In addition, con adequate battee remains on the rating plate.
  TranspoTP with the low batteoltage or the batteeached battee may unstabilize the backup data unstable during transportation.

• Make sure to transpoTP main unit and/or relevant unit(s) in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specications of this manual, as they are precision devices. Failure to do so may cause the unit to fail.
  Check if the unit operates correctly after transportation.

Associated Manuals （For the details of a PLC to be connected, refer to the PLC user’s manual respectively.）

Bundled items

128MB, built-in Ethernet inteace
TP(TL)2507-(E)| 7”[800×480 dots], TFT color, 24 bit color, 24VDC, Memoe 128MB, built-in Ethernet inteace
TP(TL)2504-(E)| 4.3”[480×272 dots], TFT color, 24 bit color, 24VDC, Memoe 128MB, built-in Ethernet inteace
Model name| Bundled items| Quantity
---|---|---
TP(TL)2510-(E)
TP(TL)2507 -(E)| Mounting fitting| 4
TP25 General Description (this manual)| 1
TP16-PLC-R4-8P-3M| 1
TP(TL)2504 -(E)| Mounting fitting| 4
TP25 General Description (this manual)| 1
TP16-PLC-R4-8P-3M-elbow| 1

Product oveview

1.1 TP(TL)2510-(E ) Paternal dimension

1.2 TP(TL)2507-(E) Paternal dimension

1.3 TP(TL)2504-(E) Paternal dimension

Specifications

2.1 General specifiscations

-20-60°C
Operating/storage ambient humidity| 10 to 90% RH, non-condensing (The wet bulb temperature is 39°C or less.)
When the ambient temperature exceeds 40°C, maintain the absolute humidity at 40°C and 90%
Vibration resistance| Conform to IEC 61131-2| | Frequency| Acceleration| Half- amplitude| Sweep count
Under intermittent vibration| 5 – 8.4Hz| —| 3.5mm| 10 times each in XY and Z directions
8.4 – 150Hz| 9.8m/s²| —
Under continuous vibration| 5 -8.4Hz| —| 1.75mm| —
8.4 – 150Hz| 4.9m/s²| —
Shock resistance| Conforms to IEC 61131-2 (147m/s 2, 11 ms, 3 times each in the X, Y, and Z directions.)
Operating atmosphere| Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electroconductive dust particles and must be no direct sunlight. (Same as for saving)
Operating altitude 1| 2000m (6562 ft) max.
Installation location| Inside control panel
Overvoltage category 2| II or less
Pollution degree *3| 2 or less
Cooling method| Self-cooling
Grounding| Class D grounding (100Ω or less). To be connected to the panel when the grounding is not possible.

1 D o not use or store the TP under pressure higher than the atmospheric pr essure of altitude 0m. Failure to obsee this instruction may cause a malfunction. When the air inside the control panel is purged by pressurization, the suace sheet may be lifted by higher pressure. As a result, the touch panel may be diess, and the sheet may be peeled off.
2 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the machineithin the premises.
Categos to equipment for which electrical power is supplied from ed facilities.
The surge voltage withstand level for up to the rated voltage of 300 V is 2500 V.
*3 This index indicates the degree to which conductive material is generated in the environment where the equipment is used.
In pollution degree 2, only non-conductive pollution occurs but temporativity may be produced due to condensation.

2.2 Peormance specifications

W95.04(3.74)xH53.86(2.12)mmi (inch) (Horizontal format)
Display character| 16-dot standard font: 50 characters x 30 lines (Horizontal format)| TBD
Display color| 24 bit color
Brightness| Multiple level adjustment
Backlight| LED-type (No replacement required) Backlight OFF/ screen saving time can be set.
Touch panel 3| Type| Analog-resistive film type
Key size| Minimum 2 x 2 [dots] (per key)
Number of points touched simultaneously| Simultaneous 2-point presses prohibited (Only one point can be touched)
Life| 1 million times (Operating force 0.98N max.)
Memory| C drive| 1 2 8M Flash + 1 2 8M DDR3
Built-in interface| RS-485-4W
RS-485-2W| COM1| RS-485, 1ch
Transmission speed: 115200/ 57600/ 38400/ 19200/ 9600/ 4800bps Connector shape: D-Sub 9pins (Male)
Application: For communication with controllers
Terminating resistor: External setting| Only support for COM1/COM3.
COM2
RS-232| COM1| RS-232, 1ch
Transmission speed: 115200/ 57600/ 38400/ 19200/ 9600/ 4800bps Connector shape: D-Sub 9pins (Male)
Application: For communication with controllers
COM2
COM3
COM4
Ethernet4| Data transfer method: 100BASE-TX, 10BASE-T, 1 ch Connector shape: RJ-45 (modular jack)
Application: Support MODBUS TCP Server
For PC connection(Project data upload/download)
USB| USB (full speed, 12Mbps) standard, lch
Connector shape: Mini-B
For application: For PC connection(Project data upload/download)
SD card 5| Conform to the SD standard, lch
Supported memory card: SDHC memory card, SD card For application: Project data upload/ download| Not provided.
Buzzer output| Single tone (Long/ short/ off adjustable)
Protective structure6| IP65F (only the front part of the panel)
External dimensions| W272(10.71) xH214(8.43) xD56 (2.21)(mm| W206(8.11) xH155(6.11) xD50(1.97)mm| W128(5.04)xH102(4.01)xD28(1.10)[mm] (inch)
Panel cutting dimensions| W258(10.16) xH200(7.88) mm (Horizontal format)| W191(7.52) xH137(5.40) (mm](inch) (Horizontal format)| W119(4.69)xH93(3.66)[mm] (inch) (Horizontal format)
Weight| Approx.1.3kg(excluding mounting fixture)| Approx.0.9kg(excluding mounting fixture)| Approx.0.26kg(excluding mounting fixture)

1 TP series are standard conation models. TL series are more lowcost.
2 Bright dots(always lit) and dark dots (unlit) may appear on a LCD panel. It is impossible to avoid this symptom, as the liquid c s of a great number of display elements. Flickers and paial discoloration may be generated on the liquid cstal display panel due to individual dierences of panel. Please note that these phenomena appear due to its characteristics and are not caused by product eect.
3 The touch panel is an analog-resistive type. Simultaneous pressing of two or more areas on the panel may activate the switch between those areas. Do not press two or more areas on the panel simultaneously.
4 Only for “-E” models.
5 TL models do not suppod, TP models suppod.
6 Note that this does not guarantee all users’ operation environment. In addition, the product may not be used in environments under exposition of oil or chemic als for a long-period time, or in environments filled with oil – mist

2.3 Communication port

COM1/COM3 Communication port ( 9-pin male)

COM2/COM4 Communication port ( 9-pin male)

Note: Three models apply to COM1/COM3 communication po. However, TP(TL)2504-(E) does not apply to COM2/COM4 communication port.

2.4 Power specications

terminals and earth)
Insulation resistance| 500VDC across power terminals and earth, 10M0 or more by an insulation resistance tester

Communication cable connection example

1. Take the communication cable of RS485-4 inteace for TP2507-E and 8PIN RS422 inteace for HCFA LX1S、LX1N、HCA1，HCA2，HCA8 as example.
2. HCFA PLC communication port RS485-2cable DB9 Female
3. HCFA PLC communication port RS232 cable DB9 Female

Product naming rule

1. “TP”: Pref HCFA HMI, abbreviation of touch panel.
   TP series are standard conation models. TL series are more lowcost.

2.  “25” is the series number of touch panel, which belongs to TP2000 series.

3. “07（04 or 10）” is the screen size code. 04 represents 4.3” LCD panel, that is TP2504-E. 07 represents 7” LCD panel, that is TP2507-E. 10 represents 10” LCD panel, that is TP2510-E.

4. “-E”: The main unit is built in Ethernet function.

4.1 Model name and function conation description

Parameter| TL2507
TL2510| TP2507
TP2510| TP2507-E
TP2510-E
---|---|---|---
Color display| 24-bit| 24-bit| 24-bit
Built-in Ethernet| ×| ×| √
Built-in SD card| ×| √| √
USB HOST| √| √| √
USB DEVICE| √| √| √
COM1/COM3| √| √| √
COM2/COM4| ×| √| √
Isolated power supply| Non-isolated power Surge protection| Non-isolated power Surge protection| Non-isolated power Surge protection

Note: The conation of TP2504-E is dierent from the above. There is no SD card and COM2/COM4 in the standard conation. And the power is non-isolated.

Notication of CE marking

The following products have shown compliance through direct testing ( to the identied standards) and design analysis (forming a technical construction le) to the European
Directive for Electromagnetic Compatibility (2004/108/EC) when used as directed by the appropriate documentation.

• This product is designed for use in industrial applications.
• Manufactured by: Zhejiang Hechuan Technology Co., Ltd
• Manufactured at: No.9, Fucai Road, Longyou industrial zone, Quzhou city, Zhejiang province, PRC
  – Type: Graphic operation terminal
  – Model: TP2000 series

EN61131-2 : 2007
Programmable controllers- Equipment, requirement and tests| EMI| Compliance with all relevant aspects of the standard.
(Radiated Emissions)
EMS| Compliance with all relevant aspects of the standard.
(ESD,RF electromagnetic field, EFTB, Surge, RF conducted disturbances and Power frequency magnetic field)

For more details, please contact HCFA distributor.
Website: http://www.hechuanplc.net/

This manual confers no industrial propey rights or any rights of any other kind, nor does it confer any patent licenses. HCFA cannot be held responsible for any problems involving industrial propey rights which may occur as a result of using the contents noted in this manual.
Warranty
HCFA will not be held liable for damage caused by factors found not to be the cause of HCFA; oppounity loss or lost prots caused by faults in the HCFA products; damage, seconda damage, accident compensation caused by special factors unpredictable by HCFA; damages to products other than HCFA products; and to other duties.

For safe use

• This product has been manufactured as a general-purpose paor general industries, and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with HCFA.
• This product has been manufactured under strict quality control. However when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.

HCFA Technology Co.,Ltd
Address: No.9, Fucai Road, Longyou industrial zone,
Quzhou city, Zhejiang province, PRC
Phone: 0570-7117888 (Switchboard)
Fax: 0570-7882868
Website: http://www.hcfa.com.cn/
E-mail: 400@hcfa.cn

References

• HomePage_禾川

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>