ORAC DECOR W113F 3D Wall Covering Instruction Manual
- June 8, 2024
- ORAC DECOR
Table of Contents
INSTALLATION INSTRUCTIONS
3D WALL COVERING
**INSTALLATIE VAN 3D WALL COVERING
**
Length
INSTALLATION
Ready? Set? Go!
INSTALLATION GUARANTEE
Storage and installation conditions: Store profiles and adhesives at room temperature and wait 24 hours before installing.
| | | |
---|---|---|---|---
Dust free| Sand and wash surface| Flat wall & ceilings| Dry| No grease
Online glue calculator
https://www.oracdecor.com/en/glue-calculator
ONLY FULL GUARANTEE WITH DECOFIX
| | |
---|---|---|---
Seal wall/ceiling| Use Decofiller for the top of a horizontal frame in case of
low panelling| DecoFix Power
Very strong MS-Polymer-based installation adhesive
FDP700 290 ml | 7 > 8m| DecoFiller
Ready to use lightweight acrylic filler
FL300 310 ml | 30 m
Non-porous or humid surface, interior
The finished lateral sides don’t require joint glue
READ CAREFULLY
CHOOSE THE CONSTRUCTION
length < 200cm / 78 3 /4” (max. full length)
Using horizontally positioned (intermediate) profile
length > 200cm / 78 3/4”
Uniform wall covering
length <
200cm / 78 3 /4” (max. full length)
Using horizontally positioned (intermediate) profile
**WORK METHOD
**
Always
install a skirting board
Provide an expansion gap of 1mm/meter (3/64” per 39 3/8”) above the skirting
board (and at the ceiling)
length < 200cm / 78 3/4” (max. full length)
Using horizontally positioned (intermediate) profile
ADHESIVES + FILLER
Use DecoFiller for all vertical seams and for the top of a horizontal frame in
the case of low panelling
Do not apply DecoFiller in expansion gaps
Do not apply DecoFix Extra
length < 200cm / 78 ¾” (max. full length)
Using horizontally positioned (intermediate) profile
INSTALLATION
Install a skirting board
See instructions
https://www.oracdecor.com/en_gb/installation
Apply DecoFix Power all around and on the length of the middle rib
Push firmly and remove excess glue
Provide expansion gap a rato 1mm/m (3/64” per 39 3/8”)
Install a finishing or intermediate profile
FINISH
Use DecoFiller to smooth out the visible joints and all vertical seams
Wait 15 minutes and sand gently
Paint the installed panels (with a spray gun)
EXAMPLES
length > 200cm / 78 3/4”
Uniform wall covering
WORK METHOD
Always install a skirting board
Provide an expansion gap of 1mm/meter (33/64” per 39/8”) above the skirting board (and at the ceiling)
ADHESIVES
Large areas: use headless nails on the side of the panel for extra fixation
Do not apply DecoFix Extra and DecoFiller in expansion gaps
INSTALLATION
| 
---|---
Install a skirting board| See instructions| Apply DecoFix Power all around and
on the length of the middle rib| Start by placing at the bottom, at an outer
corner
https://www.oracdecor.com/en_gb/installation
| 
---|---
Push firmly and remove excess DecoFix Power| Measure remaining length| Mark on
the panel| Saw to size mechanically or manually
Place the shortened piece above the first panel| Position the panels closely
and carefully together| Push firmly
Start second row (steps 1-10) by placing panels from ceiling down| Large areas: use headless nails on the side of the panel for extra fixation| Finish the full height of the 2nd row
FINISH
Wait 15 minutes and sand gently| Paint the installed panels (with a spray gun)
EXAMPLES
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>