ORAC DECOR W108F 3D Wall Covering Instruction Manual

June 8, 2024
ORAC DECOR

ORAC DECOR logo

INSTALLATION INSTRUCTIONS
3D WALL COVERING

**INSTALLATIE VAN 3D WALL COVERING

**

Length

ORAC DECOR W108F 3D Wall Covering - FIG1

ORAC DECOR W108F 3D Wall Covering - QR code

WWW.ORACDECOR.COM

INSTALLATION

Ready? Set? Go!
INSTALLATION GUARANTEE

Storage and installation conditions: Store profiles and adhesives at room temperature and wait 24 hours before installing.

| | | |
---|---|---|---|---
Dust free| Sand and wash surface| Flat wall & ceilings| Dry| No grease

Online glue calculatorORAC DECOR W108F 3D Wall Covering - QR
code1https://www.oracdecor.com/en/glue-calculator

ONLY FULL GUARANTEE WITH DECOFIX

| ORAC DECOR W108F 3D Wall Covering - FIG3|
---|---|---
Seal wall/ceiling| Connection between short sides of panels| Finish seams with Decofiller
| |
---|---|---
DecoFix Power
Very strong MS-Polymer-based installation adhesive
FDP700 290 ml | 7 > 8m| DecoFix Extra
Polyurethane-based adhesive
FX200 310ml | min. 80m
FX210 tube 80ml | min. 20m| DecoFiller
Ready to use lightweight acrylic filler
FL300 310 ml | 30 m

Non-porous or humid surface, interior

The finished lateral sides don’t require joint glue

READ CAREFULLY

CHOOSE THE CONSTRUCTION

length < 200cm / 78 3 /4” (max. full length)
Using horizontally positioned (intermediate) profile
length > 200cm / 78 3/4”
Uniform wall covering
ORAC DECOR W108F 3D Wall Covering - FIG8length < 200cm / 78 3 /4” (max. full length)
Using horizontally positioned (intermediate) profile

**WORK METHOD

**

ORAC DECOR W108F 3D Wall Covering - FIG9 Always install a skirting board
Provide an expansion gap of 1mm/meter (3/64” per 39 3/8”) above the skirting board (and at the ceiling)
length < 200cm / 78 3/4” (max. full length)
Using horizontally positioned (intermediate) profile

ADHESIVES + FILLER

ORAC DECOR W108F 3D Wall Covering - FIG10

ORAC DECOR W108F 3D Wall Covering - FIG11

Use DecoFiller for all vertical seams and for the top of a horizontal frame in the case of low panelling
Do not apply DecoFiller in expansion gaps
Do not apply DecoFix Extra
length < 200cm / 78 ¾” (max. full length)
Using horizontally positioned (intermediate) profile

INSTALLATION

ORAC DECOR W108F 3D Wall Covering - FIG13

Install a skirting board
See instructions

https://www.oracdecor.com/en_gb/installation

ORAC DECOR W108F 3D Wall Covering - FIG14

Apply DecoFix Power all around and on the length of the middle rib
Push firmly and remove excess glue

ORAC DECOR W108F 3D Wall Covering - FIG15

Provide expansion gap a rato 1mm/m (3/64” per 39 3/8”)

ORAC DECOR W108F 3D Wall Covering - FIG16

Install a finishing or intermediate profile

FINISH

ORAC DECOR W108F 3D Wall Covering - FIG17

Use DecoFiller to smooth out the visible joints and all vertical seams
Wait 15 minutes and sand gently
Paint the installed panels (with a spray gun)

EXAMPLES

ORAC DECOR W108F 3D Wall Covering - FIG18

ORAC DECOR W108F 3D Wall Covering - FIG19

length > 200cm / 78 3/4”
Uniform wall covering

WORK METHOD

ORAC DECOR W108F 3D Wall Covering - FIG20

Always install a skirting board

Provide an expansion gap of 1mm/meter (33/64” per 39/8”) above the skirting board (and at the ceiling)

ADHESIVES + FILLER

ORAC DECOR W108F 3D Wall Covering - FIG22

ORAC DECOR W108F 3D Wall Covering - FIG23

Use DecoFiller for ALL joints between the panels
Use DecoFix Extra for all SHORT joints between the panels
Large areas: use headless nails on the side of the panel for extra fixation
Do not apply DecoFix Extra and DecoFiller in expansion gaps

INSTALLATION

ORAC DECOR W108F 3D Wall Covering - FIG25| ORAC
DECOR W108F 3D Wall Covering - FIG26
---|---
Install a skirting board| See instructions| Apply DecoFix Power all around and on the length of the middle rib| Start by placing at the bottom, at an outer corner

https://www.oracdecor.com/en_gb/installation

ORAC DECOR W108F 3D Wall Covering - FIG27| ORAC
DECOR W108F 3D Wall Covering - FIG29
---|---
Push firmly and remove excess DecoFix Power| Measure remaining length| Mark on the panel| Saw to size mechanically or manually

ORAC DECOR W108F 3D Wall Covering - FIG30| ORAC
DECOR W108F 3D Wall Covering - FIG31
---|---
Apply DecoFix Extra to the short seam of thepanel as close to the wallside as possible| Place the shortened piece above the first panel| Position the panels closely and carefully together| Push firmly
ORAC DECOR W108F 3D Wall Covering - FIG32| ORAC
DECOR W108F 3D Wall Covering - FIG33
---|---
Remove excess DecoFix Extra| Start second row (steps 1-10) by placing panels from ceiling down| Large areas: use headless nails on the side of the panel for extra fixation| Finish the full height of the 2nd row

FINISH

ORAC DECOR W108F 3D Wall Covering - FIG34

inish all vertical seams (and the seams between the panels) with
DecoFiller| Remove excess DecoFiller| Wait 15 minutes and sand gently| Paint the installed panels (with a spray gun)

EXAMPLES

ORAC DECOR W108F 3D Wall Covering - FIG35

ORAC DECOR logo

www.oracdecor.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals