Symatoys X200W Folding Drone User Manual

RADIO_CONTROLLED PRODUCT
X200W FOLDING DRONE
User manual V1.0

X200W Folding Drone

+1 718-312-0558(US) +44 (0)7723708421(UK) +4933545519201(DE)
usa@symatoys.com(US) eu@symatoys.com(EU)
https://www.symatoys.com  https://www.symatoys.com.cn

Important Notices

1. Please read this manual carefully so as to protect your legitimate rights and interests and to make sure the drone is used correctly.
2. When using this product, please strictly observe and perform the requirements which include but are not limited to the instructions and safety guidelines. The user shall bear the related responsibilities and losses for any personal injury, accidents, property loss, legal dispute or any other adverse events causing a conflict of interest resulting from the use of the product or any irresistible factors that violate the safety instructions. Syma will not take any responsibility.
3. Once you start using the product. you are deemed to have read, understood, and accepted the terms and contents of the instructions (including disclaimers, safety instructions, warning instructions, etc) included with this product.
4. In case you are having challenges on any aspect of the product, may it be operation or maintenance, please contact our customer service directly.

Safety Guidelines

1. Please store the smaller-sized drone accessories in places that are out of reach of children.
2. For all first-time flights, the left joystick must be slowly pushed up in order to prevent the drone from ascending too fast in case of unnecessary collision and possible damage and injury.
3. When the flight is ended, first turn off the power of the remote control. Then turn off the power of the drone.
4. Avoid placing the batteries in places with high temperatures and exposure to heat.
5. Take extra precautions to ensure that the drone is at a minimum distance of 15 feet from the pilot, other people, and animals in order to prevent physical injury during flight operations. A minimum separation distance of 20 cm must be maintained between the user’s body and the device under normal use conditions.
6. Children under the age of 8 must be instructed with the correct and safe operation of the drone by an adult.
7. Children must be under adult supervision when using this drone.
8. Non-rechargeable batteries are not to be recharged; Batteries are to be inserted with the correct polarity; Different types of batteries or new and used batteries must not be mixed.
9. The supply terminals can not be short-circuited.
10.  Discharge the battery to 40%-50% (On a full charge, fly for half of the total flight time) if it will not be used for 10 days or more, this can greatly extend the battery life.
11. Please keep a safe distance from the spinning propellers to avoid injury.
12.  To ensure the electromagnetic environment requirement of the aviation radio (station), using remote controls in the zone, which is in a radius of about 5000m zones from the circle center of the airport runway, is forbidden. All users also should abide by   he regulation of the radio set forth by government and regulatory agencies including the duration and area.
13. Only use the recommended transformer for the model, and the transformer is not a toy. Check the cord, plug, enclosure, and other parts of the transformer regularly. If any damages have been discovered, please immediately stop using it until it was   ompletely repaired.
14. 14. Never look steadily at the laser beam since the laser radiation.
15. NOTE: Assemble the drone under adult supervision.
16. The pilot is responsible for the safe operation, safe distance from uninvolved persons and property on the ground, and from other airspace users and shall never fly the drone above crowds (> 12 persons).
17. The packing has to be kept since it contains important information.
18. It is strongly recommended to fly in areas without airflow. Do not fly in areas with an air conditioner/electric fan or table lamp, or other electrical equipment which may be easily damaged.
19. Use only the supplied charging cable.
20. Chargers used with the drone should be examined regularly, such as the cord, plug, enclosures, and other parts. If any damages are found, please stop using it unless it is repaired or replaced.
21. Do not touch the rotating rotor, avoiding loose clothing or hair being caught in the rotor, and do not fly near the face.

Repair and Maintenance

1.  Use a dry and soft cloth to clean the product.
2. Do not expose the product to extreme heat or direct sunlight.
3. Do not immerse the product in water as this may damage the electrical components.
4. Please check the blades, motors, and batteries regularly. If any damage is found, please stop using it unless it is repaired or replaced.

Product Description

2.1 Specifications

Drone

Brand Name| SYMA
Model/ITEM NO.| X200W
Drone weight| about 38g
Drone Size| 156x142x38 mm
Range| about 30 m
Altitude| about 10 m
Motor| ø6
Battery capacity(built-in)| 3.7V 400mAh
Charging time| about 90 minutes
Flight time| about 15 mins
Remote control
Operating Frequency| 2.4 GHz
Battery| 4X1.5V”AA”(Not included)
Package contents
Drone| 1
Remote control| 1
USB charging cable| 1
Clockwise/anticlockwise propellers| 2 (A/B)
Screwdriver| 1
Phone holder| 1
User manual| 1

2.2 Download SYMA Fly APP

1. Scan the QR code with your mobile device or download the app from your app store.
   |
   ---|---

   https://itunes.apple.com/us/app/syma-fly/id1306450695?l=zh&ls=1&mt=8

|

    <http://www.symatoys.com/downshow/syma-fly-android-apk.html>  

Note:
*For better results, this application requires iOS 8.0/Android 5.0 or later.

2. WIFIConnection Operation
   ① Download SMYA FLY APP on your phone.
   ② First pair the drone with the remote control, then turn on the WiFi settings of the mobile device and select “FPVWIFI****” from the WIFI list.
   ③ Wait until your smartphone connects to the drone’s WIFI network.
   ④ Open SYMA FLY APP, select the model, and then click START the camera image will display on the screen, indicating that the connection is successful.

2.3 Drone Diagram

1. Propeller
2. Power switch
3. Charging port
4. Arms
5. Camera

2.4 Remote Control Diagram

1. Power switch
2. Left joystick (Press and hold the button, push the right joystick to complete the corresponding trimming)
3. Phone holder
4. Right joystick (short press to toggle between high and low speed mode)
5. 360°flip (Press and hold the button, push the right joystick to complete the corresponding flip)
6. One key take off/land

Product Assembly

3.1 Folding the drone

1. Unfold the arms in the direction of the arrow
2. Fold the arms in the direction of the arrow

3.2 Propeller Installation
Detaching the propellers

Remove the screws and the holder in the direction of the arrow, and then detach the propellers.

Re-installing the propellers

Place the propellers on the arm of the drone in the direction of the arrow, place the holder then tighten the screws.
Referring to the figure below, install the label “A” propeller and label “B” propeller in the corresponding positions, and use a screwdriver to tighten the screws.

Note:

1. Please make sure that the propellers are installed in the correct position. If the installation is incorrect, the drone will not be able to fly normally.
2. Since the propellers are thin, please be careful when installing them in case of accidental scratches.
3. Please use the propellers provided by our manufacturer.
4. The propellers are consumables, if necessary, please purchase additional accessories.

3.3 Drone Battery Charging

Note:

• Charge the drone with the USB charging cable that came with the product.

• The battery will take longer to charge when you use an adapter with a smaller rated current.
  Important: Battery Charging Information

  1. Rechargeable batteries should only be charged under adult supervision.
  2. Caution: Improper battery use may result in an explosion. Please dispose of the batteries according to the instructions.
  3. Don’t use or place batteries near heat sources such as fires or heaters.
  4. After flying, it is necessary to wait until the battery completely cools down before charging it as the battery’s getting too hot may cause a fire.
  5. Don’t hit or drop the battery when charging to avoid an internal short circuit.
  6. Only use the supplied charging cable for charging. If the battery is aging, please replace it with a new battery in time.
  7. After fully charged, please remove it from the adapter in time, otherwise the battery will be discharged and recharged, which will shorten the battery life.
  8. The toy is only to be connected to Class II equipment bearing the symbol:

3.4 Mobile Phone Holder Installation

3.5 Battery Installation
Remote control battery installation
Remote control battery installation: Open the battery cover on the back of the remote control, and install 4*AA batteries correctly according to the electrode instructions of the battery box(battery needs to be purchased separately)

Note:

1. When installing the battery, please make sure that the polarity of the battery matches the polarity of the battery box.
2. Do not use new and old batteries together.
3. Do not use different types of batteries together.
4. Do not use rechargeable batteries.

Flight Guide

4.1 Flight Preparation and Turning the Drone On/Off
Pairing the remote control with the drone

1. Switch on the remote control, remote control indicator light flashes slowly.
2. Switch on the drone, drone indicator light flashes from rapidly to slowly
3. Push the left throttle up.
4. Pull the throttle down and reset it to the center.
5. Both indicator lights turn solid when the pairing is successful.

Note:
After you switch on the remote control, the indicator will flash quickly, which means that the remote control is waiting to be paired with the drone.

Level calibration
Place the drone on a flat surface and move the left and right joysticks to the lower right corner for approximately 3 seconds. The indicator will flash rapidly and then turn solid, which means that the calibration process is complete.
The drone cannot be calibrated if the angle of inclination is greater than 10 degrees.

Turning the drone on

Method one
Push the left joystick fully up and return to the center. Method two
Push the left and right joysticks downward in a V shape for 2 seconds. Method three
Press the one key take off/landing button

Note:

1. If the drone is flying out of range from the remote control, the drone indicator light will start flashing and the drone will land slowly.
2. If the remote control suddenly turns off or runs out of power during flight, the drone will automatically land and come to a stop.To re-control the drone, the remote control needs to be turned on again and the pairing also needs to be done.

Turning the drone off

Method one
Push the left joystick downward for 2-3 seconds. Method two
Push the left and right joysticks downward in a V shape for 2 seconds. Method three
Press the one key take off/landing button
Note:
The drone will switch off automatically if its angle of inclination exceeds 90 degrees.

4.2 Flight Control

4.3 Flight Mode
Headless mode

Push the right joystick of the remote control to fly forward, the drone will always fly in the direction indicated by the nose when it takes off, even if the direction of the nose is changed during the flight.

1. Define the Front
   When you turn on the power for the first time and start the drone, the direction of the nose of the drone is straight ahead.

2. Enter and Exit of Headless Mode
   ① After the pairing is completed, press the “Headless Mode” button, and the remote control will emit a “beep beep..” sound, the indicator light on the drone will flash slowly, indicating that it has entered the headless mode. Press the “Headless Mode” button again. When you hear a long beep sound, the drone exit the headless mode.
   ② In the headless mode, the operator does not need to identify the position of the nose of the drone but only needs to control the drone according to the direction of the joystick of the remote control.

Trimming
Trimming forward and backward

When the drone is hovering in the air and drifting forward or backward automatically, you can press and hold the trim button and push the right joystick in the backward or forward direction to adjust until the drone is stable and then release it.
Trimming left and right

When the drone is hovering in the air and automatically drifting to the left or right, you can press and hold the trim button and push the right joystick to the right or left direction to adjust until the drone is stable and then you can release the trim button.

4.4 Smart Flight Feature
High/low speed mode
Press the speed switch button to switch between high speed and low speed.

1. The default speed is low speed when the power is on.
2. The remote control emits two beeps for high speed and one beep for low speed.

360°Flip
When you are familiar with the basic functions of the drone, you can try out the exciting flip stunts. After flying the drone to a height of more than 2 meters, press and hold the 360°flip button on the remote control, and push the right joystick forward / backward or left / right at the same time, the drone will flip in the corresponding direction.

One key take off/land

1. When the drone is in standby mode, press the one key take off/land button, the drone will automatically take off and hover at a height of 1.5 meters.
2. When the drone is in flight, press the one key take off/land button and the drone will automatically land on the ground.

Altitude hold
When you release the left joystick (throttle) after ascending/descending, the drone will continue to hover at the current height.

4.5 Protection Mechanism
Undervoltage protection
When the two indicators on the nose of the drone begin to flash, it means that the power of the drone is low. At this time, please control the drone to return.
Overcurrent protection
If the drone’s blades collide with another object or become stuck, the drone will engage the overcurrent protection mechanism.

Drone status and maintenance

Aircraft fails to take off and the indicator light
keeps flashing rapidly| 1. The aircraft and the remote control are not paired
2. The aircraft enters low voltage      protection| 1. Correctly pair the remote control with the drone. The indicator light will stay on when the pairing is successful.
2. The battery voltage of the is too low,please fully charge the battery
Fly sideways when hovering| Fly sideways when hovering| Re-do the level calibration, place the aircraft on a horizontal surface, and push
both left and right joysticks to the lower right corner for about 3 seconds. The
indicator light on the aircraft flashes quickly and then turns solid, indicating that the calibration is successful.
Unstable hovering| 1. The drone is not level calibrated
2. Unstable air pressure in bad weather conditions
3. Cluttered gyroscope data due to a violent collision| 1. Re-do the level calibration, place the drone on a horizontal surface, and push
both the left and right joysticks to the lower right corner for about 3 seconds.
The indicator light on the aircraft flashes quickly and then turns solid indicating that the calibration is successful.
2. Try to avoid flying in a bad weather and fly it in a windless environment.
3. Re-do the level calibration and operate according to point 1.
Unable to connect APP| 1. Low phone configuration
2. Abnormal network during the installation process| 1. Make sure the device is running the atest operating system to support the
app or use another smartphone to connect the drone
2. Uninstall and reinstall the app
APP and mobile image transmission are unstable| 1. Out of transmission range
2. Low phone configuration or the small cache
3. Environmental disturbances| 1. Within the controllable transmission range
2. Update your phone or clear the cache
3. Change to an open environment
Motor does not work| Check the motor for foreign objects (eg: hair, sand)| Regular inspection and cleaning
Remote control does not work| 1. Beyond the remote control distance
2. Low battery of the remote control| 1. Within the controllable flight range
2. Replace the remote control battery and install it with correct polarity.
Unable to pair the drone with the remote control| Check the battery of the drone and remote control| Charge the drone battery, or replace the battery of the remote control with the
correct installation
The aircraft vibrates violently| Check whether the blade is installed correctly or the blade is damaged| If the blade is deformed, replace the blade and install the clockwise and
counterclockwise blades correctly.

Contact Us

Please do not hesitate to contact us if you need further support.
warranty@symatoys.com.cn
+1 718-312-0558(US) +44 (0)7723708421(UK) +4933545519201(DE)

https://qrs.ly/stc7z62

For online support, please scan this code with Facebook Messenger

Product Accessories

Exploded View

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Notice.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
“This device complies with FCC radiation exposure limits set forth for general population (uncontrolled exposure).This device must not be collocated or operating in conjunction with any other antenna or transmitter.”
RF frequency band: 16.97dBm(Max)
Transmitter power: 2412MHz
Product name: DRONE
Decoration of Conformity Inserts: Hereby, GuangDong SYMA Model Aircraft Industrial Co., Ltd. declares that the radio equipment type drone is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.symatoys.com/down/declaration-of-conformity.html

WARRANTY:

LIMITED 2-YEAR WARRANTY AND FREE LIMITED REPLACEMENT PARTS FOR 2-YEARS
Symatoys.com.cn warrants to the original buyer only that its products will be free from defects in material and workmanship for 2 years from the date upon which the product is shipped, either directly from symatoys.com.cn or from an Authorized Re-seller’s location, to the buyer.
The following conditions must be eligible for warranty coverage:

1. During the warranty period product is used as intended by the manufacturer.
2. The Product has not been disassembled or modified.
3. The labels and serial numbers show no signs of tampering or altering.
4. Buyer has a warranty code obtained by registering their product online prior to making aclaim.

EXCEPTIONS: THE LIMITED WARRANTY SHALL NOT APPLY TO:

•  Damage caused by normal wear and tear
• Accident, negligence, abuse, misuse, misapplication or willful damage by buyer (or its agents), or acts of nature
• Crash or burning caused by non-manufacturing factors
• Damage caused by authorized modification or disassembly not authorized by the instruction manual
• Damage caused by incorrect use or operation
• Damage caused by mismatch or misuse of battery or charger
• Failure of the operator to follow the operating instructions or use outside the products operating parameters
• Damage caused by operating the product in or around electromagnetic interference (i.e., radio transmitting tower, high-voltage wire, substation, etc.)
• Damage caused by operating the product where there may be interference caused by other wireless devices
• Operating the product with load capacity in excess of the sale weight listed in the manual
• Operating the product with aged, damaged or unauthenticated third-party components
• Operating the product with a defective battery
  WARRANTY
  PROCEDURE: Any claims for breach of the foregoing limited warranty shall only be valid if buyer makes such claim in writing within 2 year of the date of shipment of the product to which the claim. To make a warranty claim, please email warranty@symatoys.com.cn with your full name, address, phone number, order number, vehicle type, part type, purchase date and product issue.

LIMITED REMEDY:
Symatoys.com.cn’s sole liability, and buyer’s sole remedy for any breach of the foregoing warranty shall be at Symatoys.com.cn’s option to exchange the product with a new product or a refurbished product that is functionally equivalent to the original product, or issue a credit or refund to the purchased product. Any replaced products shall be warranted as set forth herein, provided that the period within which buyer may make further claims shall be limited to the remainder of the original period. for the applicable product or 2 years, whichever is longer (although the warranty period shall be suspended during any period of replacement)
DISCLAIMER:
Haftungsausschluss:
THE WARRANTY AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES. AND Symatyos.com.cn DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, NON- INFRINGEMENT AND ANY WARRANTIES ARISING OUT OF COURSE OF DEALING, COURSE OF PERFORMANCE AND TRADE USAGE. Symatoys.com.cn IS NOT RESPONSIBLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR UNDER ANY OTHER LEGAL THEORY. INCLUDING BUT NOT UMITED TO COSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY, LOSS OF ANTICIPATED SAVINGS; LOSS OF  BUSINESS COSS OF OPPORTUNITY; LOSS OF GOODWILL, LOSS OF EPUTATION; LOSS OF DAMAGE TO COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIRECT OR CONSEQUENTIAL LOSS OR DAMAGE HOWSOEVER CAUSED INCLUDING THE REPLACEMENT OF EQUIPMENT AND
PROPERTY. ANY COSTS OF RECOVERING OR REPRODUCING ANY DATA STORED IN OR USED WITH THE PRODUCT OR ANY FAILURE TO MAINTAIN THE CONFIDENTIALITY OF INFORMATION STORED THE PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages. so the above limitation or exclusion may not apply to you. In addition, some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you.
FREE REPLACEMENT PARTS FOR 2 YEARS : Symatoys.com.cn shall also make available any spare part needed for registered vehicles free of charge for 2 years from the date of purchase, with the exception of batteries, motors. circuit boards and transmitters. Shipping charges may apply Limit one part type request per registered vehicle (e.g., registrants are entitled to one extra set of batteries per registered vehicle}. To request spare parts. please email warranty@symatoys.com.cn with your warranty code, vehicle name/model, current shipping address, purchase date and part type
GET YOUR WARRANTY CODE AT symatoys.com.cn/pages/warranty- signup HAVE YOUR ORDER NUMBER AND/OR VEHICLE UPC READY

European Representative：
CET PRODUCT SERVICE LTD.
Osterholzallee 144
71636 Ludwigsburg Germany
Phone：+4971416432236
Email：info.cetservice@gmail.com

British Representative：
CET PRODUCT SERVICE LTD.
Beacon House Stokenchurch Business Park,
Ibstone Rd, Stokenchurch
High Wycombe HP14 3FE UK
Tel： +447419325266
E-mail：info.cetservice@gmail.com

United States Representative：
Duvin Trade Inc 5800 Wood Sorrel Dr，Littleton，Co, 80123， United States
Phone: 718-312-0558
E-mail: amz@symatoys.com
Manufacturer: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD
Address: NO.2 WEST XINGYE ROAD LAIMEI INDUSTRIAL AREA CHENG HAI , Shantou, China
Postal Code: 515800
 +1 718-312-0558 (US) +44(0)7723708421 (UK) +49 335-4551-9201(DE)
**usa@symatoys.com
(US) eu@symatoys.com(EU)
https://www.symatoys.com** https://www.symatoys.com.cn
SYMA is a trademark of Guangdong Syma Model Aircraft Industrial Co., Ltd. registered in the United States and/or other countries.
Made in China

The company has the right of final interpretation of this user manual.

References

• Syma Toys Online Coolest Gadgets for Trendy People – Symatoys
• warranty-signup – Symatoys
• Declaration Of Conformity - SYMA Official Site
• SYMA Official Site
• Syma Toys Online Coolest Gadgets for Trendy People – Symatoys

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>