ALTO Bluetooth Total MkII Bluetooth Audio Adapter User Guide
- June 8, 2024
- ALTO
Table of Contents
Bluetooth Total MkII Bluetooth Audio Adapter
User Guide
Bluetooth® Total (MK2)
User Guide
Bluetooth Total MkII Bluetooth Audio Adapter
For technical support.
altoprofessional.com/support
For complete warranty information.
altoprofessional.com/warranty
Controls Diagram
Box Contents: Bluetooth® Total, Micro-USB Charging Cable, User Guide.
Charging Bluetooth Total: Use the included micro-USB cable to connect
Bluetooth Total to a USB power adapter (sold separately) connected to a power
outlet or your computer (powered on).
Note: Bluetooth Total may not be fully charged upon purchase. While it is
safe to use it right away, charging for 3-4 hours before initial use will
ensure a full charge and the best performance.
Controls
- XLR Output
- Stereo-Link
- Stereo-Link LED
- Pair
- Pair LED
- Power On/Off
- Power and Battery Status LEDs
- Micro-USB Charging Port
LED Activity
When ON and battery is not charging:
20–100% = Green LED lit solid.
10–20% = Green and Amber LEDs are lit solid.
0–10% = Green and Red LEDs are lit solid.
Power Standby Mode = Green LED off. Red LED flashes once every 10 seconds.
When ON and battery is charging:
Power Standby Mode = Green LED off. Red LED flashes once every 10 seconds.
5–80% Charged = Green LED is off. Amber LED flashes slowly.
80–99% Charged = Green LED flashes slowly. Amber LED is off.
100% Charged = Green LED is lit solid. Amber LED is off.
When OFF and charging:
5%–80% Charged = Green LED is off. Amber LED flashes slowly.
80%–99% Charged = Green LED flashes slowly. Amber LED is off.
100% Charged = Green LED lit solid. Amber LED is off.
Bluetooth Pairing a Single Bluetooth Total
-
Power on your Bluetooth device.
-
Power on Bluetooth Total.
-
Press and hold the Pair button for 3 seconds on Bluetooth Total. A pairing tone will sound when Bluetooth Total is in pairing mode.
Note: Press Pair again before your device is paired, to cancel the pairing process.
Note: Before pairing, turn off Wi-Fi on your device and stop any audio playback. -
Navigate to your Bluetooth device’s setup screen, find “Alto BT2” and connect.
-
When paired successfully, a confirmation tone will sound and the blue Pair LED will illuminate solid.
Note: If your Bluetooth device prompts for a pairing code, enter “0000”. -
Adjust the volume on your Bluetooth device.
To erase previous pairing settings, press and hold the Pair button for 10
seconds. A confirmation tone will sound, indicating that pairing settings have
been erased. You can now pair to a new device.
Note: When wirelessly connected to a single loudspeaker, the Left/Right
audio signal will be summed to mono.
Stereo-Linking 2 Bluetooth Total Units
- Follow steps 1-6 in the Bluetooth Pairing a Single Bluetooth Total section.
- Press and hold the Stereo-Link button for 3 seconds on the primary (left) Bluetooth Total. Press and hold the Stereo-Link button for 3 seconds on the secondary (right) Bluetooth Total.
- Both Stereo-Link LEDs will blink and a linking tone will sound while each Bluetooth Total “searches” for the other.
- When they are successfully linked, each Bluetooth Total will produce a confirmation tone and the Stereo-Link LEDs on both units will be lit solid.
To erase linking settings on the linked unit, press and hold the Stereo-Link
button for 10 seconds. A confirmation tone will sound, indicating that linking
settings have been erased.
To erase linking settings on both units, press and hold the Stereo-Link button
on the master unit for 10 seconds. A confirmation tone will sound, indicating
that linking settings have been erased.
Technical Specifications
Dimensions (width x depth x height, single unit): 1.5” x 5.4” x 0.9” /
38.1 x 137.2 x 22.9 mm
Weight (single unit): 0.18 lbs. / 0.08 kg
XLR Output: XLR Male, Balanced
Output Level: +4 dBu
Bluetooth Profile: BT 5.0, A2DP, AVRCP
Supported Audio Codec: SBC
Bluetooth Range: Up to 100 feet (30.5 m)
Battery: Battery Life: Up to 6 hours
Recharge Time: Up to 4 hours
USB Charging: 5V, 500 mA
Safety Instructions
Please note : Alto Professional and inMusic are not responsible for the
use of its products or the misuse of this information for any purpose. Alto
Professional and inMusic are not responsible for the misuse of its products
caused by avoiding compliance with inspection and maintenance procedures.
Please also refer to the included safety and warranty manual for more
information.
Notice Concerning FCC Regulations: You are cautioned that changes or
modifications not expressly approved by the part responsible for compliance
could void the user’s authority to operate the equipment. This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures: (a) reorient or relocate the receiving antenna; (b) move
this unit; (c) increase the separation between the equipment and receiver; (d)
connect the equipment into an outlet on a circuit different from that to which
the receiver is connected; (e) be sure that all cables are properly shielded,
using a choke or ferrite where appropriate; (f) consult the dealer or an
experienced radio/television technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not
be colocated or operating in conjunction with any other antenna or
transmitter.
Maximum RF Power: Bluetooth (2402–2480 MHz): 4.4 dBm.
The Maximum Permissible Exposure (MPE) level has been calculated based on a
distance of d=20 cm between the device and the human body.
To maintain compliance with RF exposure requirement, use product that maintain
a 20 cm distance between the device and human body.
Regulatory Conformance: Hereby, inMusic Brands, Inc. declares that the
radio equipment type (Bluetooth Total, Bluetooth audio adapter) is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following Internet address:
altoprofessional.com/safety.
Notice: Observe the national local regulations in the location where the
device is to be used. This device may be restricted for use in some or all
member states of the European Union (EU).
IC Warning: This device contains licence-exempt
transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development (ISED) Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may
cause undesired operation of the device.
ESD / EFT Warning: This unit may contain a microcomputer for signal
processing and control functions. In very rare situations, severe
interference, noise from an external source, or static electricity may cause
it to lock up. In the unlikely event that this should happen, turn off the
unit, wait at least five seconds, and then turn it back on again.
In an environment with radio frequency interference, the unit may malfunction
and resume normal operation after removal of the interference. For best audio
quality, avoid using this device in a high RF-radiated environment. This unit
does not exceed the Class B limits for radio noise emission from digital
apparatus set out in the radio interference regulations of the Canadian
Department of Communications.
Alto Professional is a trademark of inMusic Brands, Inc., registered in the
U.S. and other countries. The Bluetooth word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Alto
Professional is under license. All other product or company names are
trademarks or registered trademarks of their respective owners.
Correct Disposal of This Product: This marking indicates that this product
should not be disposed with other household wastes throughout the EU. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was purchased.
They can take this product for environmentally safe recycling.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>