ZYWELL ZY308 Mini Receipt Printer User Guide

Mini Receipt Printer Quick Start Guide
OUTLOOK AND INSTALL PAPER ROLL

Remove the used roll paper core if any, and insert the roll paper. The correct direction of the paper is shown in the illustration below.

STEP 1 – INSTALL THE PRINTER

1. USI3 Port
2. Serial Port
3. LAN Port
4. Cash Drawer Port Rj’ll
5. Power Port

A. Connect AC power cord to power, DC power cord to the printer.
B. Connect printer and computer/ tablet.
C. Connect the cash drawer.

Button name, indicator LED light and function

1. Feed Button: Press to feed paper manually.
2. Paper Indicator (LED Light): Blue and red lights are on means a lack of paper, no alarm means all goes well.
3. Power Indicator: Light is on means connected properly.
4. Error Indicator: When out of paper, cutter or printing head overheat occurred, the ALARM indicator twinkles.

Self-Test
Method: When the printer is connected power off, press the “FEED” button, and turn it on at the same time, 2 seconds later release TEED” button, a completed self-test will be printed out to show the printer settings.

TOOL CHANGE PRINTER IP

1. Double click “Printer Test V3.3C”

2. Setting new printer IP in new IP box

3. Click “Set New IP”, after the beep rings, the New IP address is Successfully.

4. Other setting Click”Advanced”

Add P PORT FOR DRIVER

1. Set computer IP to 192.168.1.xxx

2. Right key receipt printer in Control Panel and choose “Printer properties”

3. Click “Ports”and choose “Add Ports…”

4. Click “Standard TCP/IP Port” and “New Port”

5. Click “Next” until this. “Printer Name or IP”, write down printer IP.

6. Click “Next” until “Finish”.Then click “Close”

STEP 2 – INSTALL THE DRIVER

1. Install driver under WINDOWS OS (Steps as below). *
   

2. Select: Next.

3. Default installation folder.
   

4. Choose the right port, shown as below:

5. Create a shortcut on the desktop.
   

6. Finished.
   

7. Install by the below instruction.
   

8. Choose the right series, shown as below.

9. Click ‘OK” to configure the port.
   

10.  Choose the detect USB001,click apply, shown as below.

11. Finsh.

CUT1ER STUCK MAINTENANCE

Cutter stuck maintenance
Method (1)
Turn off the power and then restart.
Method (2)
Turn the gear on the printing head, the cutter can be returned to its original position.
Notice: To avoid damage of the printing head and automatic paper cutter, please do not open the cutter and mechanism violently.
CLEARANCE AND MAINTENANCE
Clearance
One of the following occurred, please clean the printing head.

1.  The printing is not clear.
2. Any vertical Is not clear.
3. Paper feed noisily.

Printing head cleaning steps:

1. Turn the printer off and release the power cord. Open the top cover, and take out the paper roll.
2. Wait till printing head cooling if it just finished printing.
3. Clean the printing head completely using a swab with alcohol (without water).
4. Until alcohol is completely volatilized, close the top cover.
5. Connect power again, and print a self-test to check if it is clean.

Notice:

1. Please make sure to power off when maintaining the printer.
2. Don’t touch or scratch the printing head surface, roller, and sensor.
3. Avoid gas, acetone, or another organic solvent.
4. Wait till the alcohol is completely volatilized, close the top cover, and connect the power again. Try a print self-test to make sure it works properly

Warning:
No part of this manual can be changed without agreement. The company reverses the right to modify the technologic, components, software, and hardware. You may ask the distributors for more product information. No part of a chapter in this manual can be copied or transmitted in any format without permission.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>