ZIP SEE015 CCTV Camera User Guide

ZIP SEE015 CCTV Camera

Full Instruction Manual

www.systemq.com/PDF/ manual/xSEE010.pdf

ABOUT PRODUCT

• The Rapid Deploy CCTV system is a fast and easy solution to provide CCTV protection. It consists of a 4Ch wireless receiver that plugs into a Zip NVR or DVR via its rear USB port.
• Once the wireless receiver is plugged into the Zip NVR or DVR, it can see and record the wireless Rapid Deploy CCTV cameras.
• Rapid Deploy is currently compatible with the ZIP Lite, ZIP Supa & ZIP Xtra DVR ranges (2 cameras only on a 4ch DVR) as well as 4, 8, 16, 32ch Zip NVRs. (Note it is not compatible with the ZIP SUPA-S range of recorders). Older Zip DVR/NVR models (up to 2019) may require a firmware upgrade.

HOW IT WORKS

• When the PIR is acti vated then the camera is activated and transmits data to the receiver.
• At night time the light sensor is used to determine if the Infra-Red LEDs are also activated when the camera is activated by the PIR.
• Two-way talk back can also be used when the camera is activated, using the Microphone on the front of the camera and the Built-in speakeer.

Powering & Charging the Batteries

• Status LED:

  • Red Charging
  • Green Charged (and plugged in)
  • No Light = Not Charging

• A Micro (B) USB Charger and lead is requred tor the charging and powering of the Rapid Deploy Batteries, these are not supplied.

SEE030 Solar Panel

• The Rapid Deploy solar panel with USB can be used to power and charge the batteries.
• Mount the bracket (instead of the standard mounting plate. And slot the camera onto the plate.

Mounting

1. Fix the mounting plate to the mounting surface using the screws and plugs
2. Slot the camera onto the mounting plate from above.

NVR Pre-Setup

For PoE ZIP NVRs, the IP channel config needs altering first.

1. Go to the menu, Video > IP Channels
2. Video > IP Channels
3. Switch Mode> Set to Manual Mode
4. Then proceed with Channel Setup

Channel Setup

Setup the channels for USB Wireless.

1. Go to the menu, Video> Channel Config
2. In the DVR channel list> Select USB Wireless
3. Select Apply
4. The DVR will require a reboot once applied, click OK

Pairing Overview

The cameras will need pairing, this can only be done in the menu on the recorder.

1. Go to the menu, Video > USB Wireless
2. Click Pair to start the pairing mode with the receiver
3. Select the Pair button on the rear of the camera
4. Pairing successful! Displays once complete
5. Select Switch to ON
6. Click Apply

SPECIFICATION

Camera
Audio Output| Built-in Speaker| Built-in Speaker| Via USB
PIR| Built-in 10m Range| Built-in 10m Range|
InfraRed LEDs| 6| 6|
IR Range| 8m| 8m|
Min. Illumination| 0 Lux with LEDs on| 0 Lux with LEDs on|
Noise Reduction| 3D| 3D|
White Balance| Auto| Auto|
Power Source| Battery Pack – 8700mAh (Supplied)| Battery Pack – 8700mAh (Supplied)| Powered from DVR/NVR
Input Voltage| DC 4.2V +-10%| DC 4.2V +-10%|
Current Consumption| 420mA (Activate) / 400mA (Sleep)| 420mA (Activate) / 400mA (Sleep)|
Power Connection| Micro USB (B)| Micro USB (B)| USB
Finish| White| Black| Black
Build| Plastic| Metal| Plastic
Operating Temperature| From -20 to 55 deg C| From -20 to 55 deg C|
Use| IP66 For External Use| IP66 For External Use| Internal Use Only
Bracket| Supplied| Supplied| Wall-Mount Fixings Supplied
Dimensions| (H) 136 x (W) 73 x (D) 89mm| (H) 136 x (W) 73 x (D) 89mm| (H) 25 x (W) 140 x (D) 60mm
 | SEE030
---|---
Solar Cell| Monocrystalline Silicon
Solar Conversion Rate| 20%
Maximum Power| 2.5W
Voltage| 5.25V
Current| 535mA
Operating Temperature| –30 C 70 C
Dimensions| 179mm (H) x 125mm (W) x 10mm (D) – without bracket
Weight| 447g
Build| Plastic (black)
Power Interface| MIcro USB
Cable Length| 360mm
IP Rating| IP66
Bracket| Supplied – 360 Adjustable wall mount

All specifications are approximate. System Q Ltd reservesthe right to change product specifications or features without notice. Whilst every effort is made to ensure that these instructions are complete and accurate, System Q Ltd cannot be held responsible for any losses, no matter how they arise, from errors or omissions in the se instructions, or the performance or non- performance of the equipment refered to.

WEE

This symbol indicate s that equipment must not be mixed with general household waste. For treatment, recovery and recycling please return to your local designated WEE/CG0783SS collection point as defined by your local council.

References

• Home - System Q Ltd - Systemq.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>