LEEDARSON

A60 LED BULB TUNABLE WHITE

SKU: 6VB-A806ST-Q1Z

Quickstart

This is a
secure
Light Dimmer
for
CEPT (Europe).

To run this device please connect it to your mains power supply.

To add this device to your network execute the following action:
1. Screw the CCT bulb into a standard E27 socket.2. Turn on the bulb with your wall switch to apply power to the bulb. a) If youre not using a wall switch, then use your alternate method to apply power to the bulb.3. Activate the included/excluded mode on your Z-Waveave controller or gateway.a) This may also be done through your associated app,if your ecosystem has that capability.4. Toggle the wall-switch, from OFF, then to ON. a) Or use your alternate method to toggle power from OFF, then to ON. 5. The LED bulb will flash once if it has been successfully included/excluded into your Z-Wave network.Note: If you are using 3rdpartyZ-Wave Controller or Gateway, please refer to 3rdPartys instruction on how to add a new devices to your network.Note 2: If the bulb will not join the network after repeated attempts, please use the Factory Reset procedures to clear the bulbs settings.

Please refer to the
Manufacturers Manual for more information.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

Our connected CCT tunable lighting has two functional categories, one is your basic On, Off and Dim, or in the lighting world, we just call it OFD. Using your app and controller/gateway, you can turn your lights on, off and dim them down to 5% brightness from anywhere in the world, using your smartphone. At 2700K and 800 lumens, it is a true 60W equivalent. Another one this is where the innovative technology takes over. You get your basic On, Off and Dim, but now you have the ability to tune the white color from a warm 2700K to a cool 6500K. The ability to tune the white is what we call Tunable White, or TW. Having this ability, and the ability from your app, you can now set the perfect scene and mood in your home. In the evening, while watching TV, you may want to tune down the white color to a warm, cozy 2700K. Or maybe your kids have homework, and its late, so to help keep their concentration, you turn the white color up to 6500K, which is similar to daylight.With all of our lighting, and the app that supports it, you can group lights together, set different lighting scenes for different groups and set schdules to autotmatically turns lights, and groups, on and off. Our connected lighting has the additional option for what we call Saved State. Saved State allows you to save an actual light setting in the bulb itself. This means that when you lose power, the lights will not come back on to the standard, blaring 2700K at full bright. The Saved State will allow the lights to come back on to the nice setting youve previously saved.LEEDARSON stays on the cutting edge of technology and innovation. Thats because they have a responsibility to their customers. Thats because at LEEDARSON, We build your success in IoT.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This
procedure should only be used when the primary controller is inoperable.

Physically switch the bulb on and off six (6) times for intervals of 0.5-2seconds. After the 6thtime, the bulb will flash twice indicating that its successfully reset. Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Inclusion

1. Screw the CCT bulb into a standard E27 socket.2. Turn on the bulb with your wall switch to apply power to the bulb. a) If youre not using a wall switch, then use your alternate method to apply power to the bulb.3. Activate the included/excluded mode on your Z-Waveave controller or gateway.a) This may also be done through your associated app,if your ecosystem has that capability.4. Toggle the wall-switch, from OFF, then to ON. a) Or use your alternate method to toggle power from OFF, then to ON. 5. The LED bulb will flash once if it has been successfully included/excluded into your Z-Wave network.Note: If you are using 3rdpartyZ-Wave Controller or Gateway, please refer to 3rdPartys instruction on how to add a new devices to your network.Note 2: If the bulb will not join the network after repeated attempts, please use the Factory Reset procedures to clear the bulbs settings.

Exclusion

1. Screw the CCT bulb into a standard E27 socket.2. Turn on the bulb with your wall switch to apply power to the bulb. a) If youre not using a wall switch, then use your alternate method to apply power to the bulb.3. Activate the included/excluded mode on your Z-Waveave controller or gateway.a) This may also be done through your associated app,if your ecosystem has that capability.4. Toggle the wall-switch, from OFF, then to ON. a) Or use your alternate method to toggle power from OFF, then to ON. 5. The LED bulb will flash once if it has been successfully included/excluded into your Z-Wave network.Note: If you are using 3rdpartyZ-Wave Controller or Gateway, please refer to 3rdPartys instruction on how to add a new devices to your network.Note 2: If the bulb will not join the network after repeated attempts, please use the Factory Reset procedures to clear the bulbs settings.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 255: Reset

Reset to factory configuration and removed the Z-Wave network.Reset Configuration parameter to default value.
Size: 4 Byte, Default Value: 0

SettingDescription

Technical Data

Supported Command Classes

• Association Grp Info
• Association V2
• Basic
• Configuration
• Device Reset Locally
• Firmware Update Md V2
• Manufacturer Specific V2
• Powerlevel
• Security
• Switch All
• Switch Color
• Switch Multilevel V2
• Version V2
• Zwaveplus Info V2

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>