Weiser 10 Button Z-Wave Plus v2 Deadbolt GED1800 Manual
- June 8, 2024
- Weiser
Table of Contents
- Weiser
- 10 Button Z-Wave Plus v2 Deadbolt
- SKU: GED1800
- Quickstart
- Important safety information
- What is Z-Wave?
- Product Description
- Prepare for Installation / Reset
- Inclusion/Exclusion
- Quick trouble shooting
- Association – one device controls an other device
- Configuration Parameters
- Technical Data
- Supported Command Classes
- Explanation of Z-Wave specific terms
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Weiser
10 Button Z-Wave Plus v2 Deadbolt
SKU: GED1800
Quickstart
This is a
secure
Lock
for
.
Please make sure the internal battery is fully charged.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in
this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any
loss or damage resulting from failure to comply with the instructions in this
manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal
instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart
Home. This
device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message ( two-
way
communication) and every mains powered node can act as a repeater for other
nodes
( meshed network ) in case the receiver is not in direct wireless range of
the
transmitter.
This device and every other certified Z-Wave device can be used together
with any other
certified Z-Wave device regardless of brand and origin as long as both are
suited for the
same frequency range.
If a device supports secure communication it will communicate with other
devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to
maintain
backward compatibility.
For more information about Z-Wave technology, devices, white papers etc.
please refer
to www.z-wave.info.
Product Description
A Z-Wave Plus enabled deadbolt from Kwikset, offering the latest S2 security and SmartStart functionality.Has a 10-Digit keypad with one-touch locking, tapered deadbolt designed to assist with misaligned doors, and features the SmartKey Re-Key technology with BumpGuard protection.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory
default
state. Please make sure to reset the device into factory default. You can do
this by
performing an Exclusion operation as described below in the manual. Every
Z-Wave
controller is able to perform this operation however it is recommended to use
the primary
controller of the previous network to make sure the very device is excluded
properly
from this network.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The
device needs
to be added to an existing wireless network to communicate with the
devices of this network.
This process is called Inclusion.
Devices can also be removed from a network. This process is called
Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network.
This
controller is turned into exclusion respective inclusion mode. Inclusion and
Exclusion is
then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association – one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one
device
controlling another device is called association. In order to control a
different
device, the controlling device needs to maintain a list of devices that will
receive
controlling commands. These lists are called association groups and they are
always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’
Command.
Association Groups:
Group NumberMaximum NodesDescription
1| 5| The lock will support the Lifeline association group.It supports sending
messages to a maximum of 5 nodes.These messages provide information on changes
that occur locally.
---|---|---
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock
further
enhanced features.
IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus
56.
In case of a two byte value the same logic applies: Values greater than 32768
may
needed to be given as negative values too.
Parameter 1: Status LED Control
The configuration parameter 1 is a read/write parameter with a one-byte
field, used to control the status LED. If setto on, the status LED will show
the status of the latch every 6 seconds. If set to off, the status LED will
not beshown.
Size: 1 Byte, Default Value: 1
SettingDescription
0 | Turns Status LED off |
---|---|
1 | Turns Status LED on |
Parameter 10: Handing Control
The configuration parameter 10 is a read/write parameter with a one-byte
field. When this parameter is read, it willreturn the handing of the lock.
When this parameter is written, it will run a handing operation. When written
with avalue of 0x01, it will cause the lock to cycle through locking and
unlocking until it determines the correct handing.It is suggested that this
operation occur while the door is opened so that no obstructions will be in
the way for theoperation. After the completion of the handing process, a
Configuration Report message will be sent back to therequestor. It will
contain a non-zero value for success or a zero value for failure.
Size: 1 Byte, Default Value: 0
SettingDescription
0 | Unknown latch position (get/read from lock) |
---|---|
0 – 1 | Initiate the handing process (set/write to lock) |
1 – 0 | Right handed lock (get/write to lock) |
2 – 0 | Left handed lock (get/write to lock) |
Parameter 2: Sound Control
The configuration parameter 2 is a read/write parameter with a one-byte
field, used to control the locks buzzer. Ifset to on, the buzzer is enabled
and will sound during normal events. If set to off, the buzzer is disabled,
and thebuzzer sound will not occur.
Size: 1 Byte, Default Value: 1
SettingDescription
0 | Turns the sound (buzzer) off |
---|---|
1 | Turns the sound (buzzer) on |
Parameter 3: User Program Button Control
The configuration parameter 3 is a read/write parameter with a one-byte
field, used to control the user programbutton. If set to on, the program
button is available for user code maintenance. If set to off, the program
button isnot available for user code maintenance.
Size: 1 Byte, Default Value: 1
SettingDescription
0 | Disables the program button |
---|---|
1 | Enables the program button |
Parameter 4: Secure Screen Control
The configuration parameter 4 is a read/write parameter with a one-byte
field, used to control the secure screenfunctionality on touch locks only.
This parameter is not used on non-touch locks and will be ignored. If set
toenabled, the touch screen will display the secure screen functionality when
woken. If set to disabled, the touchscreen will not display the secure screen
functionality when woken.
Size: 1 Byte, Default Value: 1
SettingDescription
0 | Disables secure screen (Touch products only) |
---|---|
1 | Enables secure screen (Touch products only) |
Parameter 40: Factory Default Control
The configuration parameter 40 is a write only parameter with a one-byte
field, used to request the lock to perform afactory reset back to its default
state. This control will cause the lock to be removed from the network,
placing thelock back to its default state. When a read is issued for this
parameter, a 0 will be returned.
Size: 1 Byte, Default Value: 0
SettingDescription
0 | No action (get) |
---|---|
1 | Perform a full factory reset (set) |
2 | Perform a modified factory reset (set) – for production only |
Parameter 46: Motor Load Value
The configuration parameter 46 is a read only parameter with a four-byte
field.It is used to retrieve the calculated sideload value from the last motor
run that was performed.This value is used to represent the amount of
powerneeded to run the motor, giving the opportunity to see if any resistance
was encountered based on the value readfrom a free running motor with no
resistance.
Size: 4 Byte, Default Value: 0
SettingDescription
0 – 16777215| Provides an insight into the amount of resistance encountered by
motor
---|---
Technical Data
Hardware Platform | ZGM130 |
---|---|
Device Type | Lock |
Network Operation | Listening Sleeping Slave |
Firmware Version | HW: 1 FW: 7.13:69.28 |
Z-Wave Version | 7.13.6 |
Certification ID | ZC12-21080301 |
Z-Wave Product Id | 0x0090.0x0811.0x03A8 |
Firmware Updatable | Not Updatable |
Door Lock Type | Deadbolt |
Security V2 | S2_ACCESS_CONTROL |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |
Supported Command Classes
- Antitheft V2
- Association Grp Info V3
- Association V2
- Basic V2
- Battery
- Configuration V4
- Device Reset Locally
- Door Lock Logging
- Door Lock V4
- Firmware Update Md V5
- Indicator V3
- Manufacturer Specific V2
- Multi Channel Association V3
- Notification V8
- Powerlevel
- Schedule Entry Lock V3
- Security
- Security 2
- Supervision
- Time Parameters
- Transport Service V2
- User Code V2
- Version V3
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
-
Controller — is a Z-Wave device with capabilities to manage the network.
Controllers are typically Gateways,Remote Controls or battery operated wall controllers. -
Slave — is a Z-Wave device without capabilities to manage the network.
Slaves can be sensors, actuators and even remote controls. -
Primary Controller — is the central organizer of the network. It must be
a controller. There can be only one primary controller in a Z-Wave network. -
Inclusion — is the process of adding new Z-Wave devices into a network.
-
Exclusion — is the process of removing Z-Wave devices from the network.
-
Association — is a control relationship between a controlling device and
a controlled device. -
Wakeup Notification — is a special wireless message issued by a Z-Wave
device to announces that is able to communicate. -
Node Information Frame — is a special wireless message issued by a
Z-Wave device to announce its capabilities and functions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>