MONOGRAM ZKPN Handle Mounting Fastener Kit For Custom Panels Instruction Manual

ZKPN Handle Mounting Fastener Kit For Custom Panels
Instruction Manual

Installation Instructions

Before you begin – Read these instructions completely and carefully.
Note to Installer: Be sure to leave these instructions with the Consumer.
Note to Consumer: Keep these instructions with your Installation Instructions for future reference.
Pour obtenir une version française de ce manuel d’instructions, visitez notre site monogram.com
Para consultar una versión en español de este manual de instrucciones, visite nuestro sitio de internet monogram.com

****To reduce the risk associated with choking, do not allow children under 3 years of age to have access to small parts during the installation of this product.

NOTE: 36″ wide built-in bottom freezer applications require specific handle kits for drawer panel applications on both Standard Case Flush and Flush Inset installations.
All other platforms are recommended to follow comparable stainless steel models for Minimalist and Statement handles.

ZKSP1H1CNSS
ZIC360NN| ZKGC3H3PNSS| ZKGC3H3CNSS

This kit allows for the attachment of up to three Monogram Minimalist or Statement collection handles on custom panels.

Parts List:

A – Spacer (Qty 6)
B – Threaded bracket (Qty 6)
C – Handle Mounting Fastener (Qty 6)
D – 5/16 countersunk screw (Qty 6)

Tools and Materials Required:

Allen Key (Provided with the kit)
Drill, 1/2” and 11/32” drill bit and 1” router bit
Custom door panel
Safety glasses
Center punch
Hammer
Pencil
Measuring tape or scale
Monogram Statement or Minimalist handle collection
This kit contains the required parts to attach a total of three handles.

Handle Mounting Fastener insert assembly:

• Assemble parts A, B, and C as illustrated and create assembly E

Table 1

This instruction provides for the installation of a Statement or Minimalist handle collection on a 3/4” standard or flush inset custom panel.

DRILL PILOT HOLES

• Measure, mark and draw a line 1-1/4” (3.18 cm) from the handle side edge, top to bottom.
• Please refer to Table 1 on page 1 for1/2” (1.27cm) hole center to center distance (L)
• Center punch to mark hole locations.
• Drill 1/2” (1.27cm) pilot holes from the appearance side and through the entire panel thickness.
• Drill 11/32” (0.87cm) pilot holes from the appearance side and through the entire panel thickness. (On vertical handle panels, drill hole 0.720” (1.83cm) below the 1/2”  (1.27cm) hole on the top side of the door panel and 0.720” (1.83cm) above the 1/2” (1.27cm) hole on the bottom side of the door panel. On Horizontal handle panels, drill hole 0.720”  (1.83cm) towards the center of the door from 1/2” (1.27cm) hole.)
• Use a 1” (2.54cm) router bit to route 1/4” (0.64 cm) deep on a 3/4” (1.91 cm) panel. See illustration.

NOTE: The routing counter bore in the rear of the decorative panel must ensure 1/2” (1.27 cm) material thickness remains for handle support.

HANDLE ASSEMBLY

• Insert Handle Mounting Fastener assembly E from the nonappearance side of the panel.

• Place the handle caps over the insert Handle Mounting Fastener on the door. Take care to support the handle so it doesn’t fall and scratch the appliance finish.
  Make sure both handle caps are resting on the face of the door.

• Lock one end of the handle into position by tightening the countersunk screw D with the Allen wrench provided.

• Keep supporting the handle as you lock the other end of the handle into position by tightening the countersunk screw D.

• Finally, tighten the set screw in the handle caps using the Allen wrench provided in the handle kit. DO NOT over-tighten the set screw using a power tool.

NOTE: Set screw location in end cap will vary by model.
When installing horizontal handles, position the handle so that the set screws are facing downward.

References

• Monogram Appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>