Qubino (Goap)

Luxy Smart Light

SKU: GOAEZMNHQD1

Quickstart

This is a
secure
Color Switch
for
Europe.

To run this device please connect it to your mains power supply.

1. Scan QR code on device label and add S2 DSK to Provisioning List in gateway (hub).

2. Connect the device to the power supply.

3. Make sure the device is within direct range of your Z-Wave gateway (hub).

4. Inclusion will be initiated automatically within few seconds of connection to the power supply and the device will automatically enrol in your network (when the device is excluded and connected to the power supply it automatically enters the LEARN MODE state).

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

Luxy Smart Light is an innovative light source that gently illuminates in more than 16 million colours and easily fits into places of your light switch or socket. It can be used standalone, as ambient light, or as a smart home device. With an integrated beeper, it enables a unique combination of sound and visual notifications. It can be controlled with a touch on one of the 4 sides on the touch-sensitive surface (or touch screen) or remotely via a smartphone. It can be set to work automatically, according to the pre- programmed scenes, created on the Z-Wave gateway. Set the Luxy Smart Light as a visual alarm, for a gentle wake-up, with colours simulating the sunrise or illuminate your corridor in the night-time, so you dont have to turn on the main light or stumble in the dark.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This
procedure should only be used when the primary controller is inoperable.

1. Connect the device to the power supply.

2. Press once on button 2 – right.
3. One press on button 3 – down for enabling full white.
4. When full white is enabled, press, and hold button 4 – left for 10 seconds. After 10 seconds, the device starts flashing blue 1 second on, 0.5 second off.

5. After 10 seconds the device stops flashing and turns full blue.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.

Installation

Electrical Diagram (230V)

As a smart light

Connected to a switch

NOTE: Antenna positioning

“• Place the antenna as far as possible from metal elements as they may cause signal interference.

“• Do not shorten the antenna.

The device”’s antenna should be as upright as possible. This ensures the device”’s operational range is maximized (up to 30 m (98 feet) line of sight).

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Inclusion

1. Press once on button 2 – right.
2. One press on button 3 – down for enabling full white.
3. When full white is enabled, press, and hold button 2 – right, between 4 and 6 seconds. After 6 seconds, the device starts flashing green (1 second ON, 0.5 second OFF). Once the device receives node ID (after 10 seconds), it stops flashing and turns full green. The procedure is always available.

Exclusion

1. Press once on button 2 – right.
2. One press on button 3 – down for enabling full white.
3. When full white is enabled, press, and hold button 2 – right for 5 seconds. After 5 seconds, the device starts flashing red 1 second ON, 0.5 second OFF. Once the device loses node ID (after 10 seconds), it stops flashing and turns full red. The procedure is always available.

Product Usage

1. Turns ON/OFF the Luxy light Dims the Luxy light
2. Switches between 4 different lighting effects (ocean, sunrise, rainbow, and nature)
3. Turns ON/OFF the white light on the Luxy Dims the Luxy light
4. Starts the colour spectrum and stops at the colour you wish to have

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 1: Digital input type

Defines the input type of device connected to digital input.
Size: 1 Byte, Default Value: 1

SettingDescription

in parameter 5)

Parameter 3: Turning off alarming

__
Size: 1 Byte, Default Value: 1

SettingDescription

0| only by z-wave command (basic set, switch multilevel set, switch multilevel start/stop level change, sound switch play tone, sound switch configuration, switch color set, switch color start/stop level change, notification report idle)
---|---
1| capacitive input or z-wave command (basic set, switch multilevel set, switch multilevel start/stop level change, sound switch play tone, sound switch configuration, switch color set, switch color start/stop level change, notification report idle)

Parameter 5: Motion sensor memory timer

Defines the time after which the output triggered by motion sensor is turned off.
Size: 2 Byte, Default Value: 10

SettingDescription

Parameter 10: Auto on timer

Defines the time after which the device is turned to last known state.
Size: 2 Byte, Default Value: 0

SettingDescription

Parameter 11: Auto off timer

Defines the time after which the device is turned to last known state.
Size: 2 Byte, Default Value: 30

SettingDescription

Parameter 30: Restore state on power failure

__
Size: 1 Byte, Default Value: 1

SettingDescription

0| disabled (the device will not restore state on power failure and will remain off)
---|---
1| enabled (the device will restore state on power failure)

Parameter 50: Beeper enable/disable

_This parameter affects beeper function just in case when the device receives the NOTIFICATION_REPORT. If the user sends a SOUND_SWITCH_TONE_PLAYSET (1), the buzzer still emits a serviceable tone.
Size: 1 Byte, Default Value: 1

SettingDescription

Technical Data

Supported Command Classes

• Association Grp Info V3
• Association V2
• Basic V2
• Configuration
• Device Reset Locally
• Manufacturer Specific V2
• Notification V8
• Powerlevel
• Security
• Security 2
• Sound Switch
• Supervision
• Switch Color V3
• Switch Multilevel V4
• Transport Service V2
• Version V2
• Zwaveplus Info V2

Controlled Command Classes

• Basic V2
• Switch Color V3
• Switch Multilevel V4

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>