SIGMA BUSTER 150 USB LED Bicycle Light Set User Manual
- June 8, 2024
- SIGMA
Table of Contents
SIGMA BUSTER 150 USB LED Bicycle Light Set User Manual
CE INFORMATION
- SIGMA-ELEKTRO GmbH hereby declares that the BUSTER 150 comply with the fundamental requirements and other relevant regulations of Directive 2014/30/EU and RoHS Directive 2011/65/EU. You can find the CE declaration at: ce.sigmasport.com/buster150
WARNING NOTICE
- Possible danger from optical radiation! Never look directly into the lamp below use and never point it at other people’s eyes
FCC DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. This equipment should be installed and operated with a minimum distance of 5 millimeters between the radiator and your body.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
Radiation Exposure Statement: The product complies with the FCC portable
RF exposure limit set forth for an uncontrolled environment and is safe for
intended operation as described in this manual. Further RF exposure reduction
can be achieved if the product can be kept as far as possible from the user
body or set the device to lower output power if such a function is available.
UKCA STATEMENT
We, SIGMA-ELEKTRO GmbH, declare that the equipment above has been tested in our facility and found in compliance with the requirement limits of applicable standards, in accordance with the Radio Equipment Regulations 2017 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. The test record, data evaluation, and Equipment Under Test (EUT) configurations represented herein are true and accurate under the standards herein specified. More SIGMA Bike Computers at sigmasport.com Designed in Germany and Manufactured in China
ACCESSORIES
CONSTRUCTION
- SILICONE HOLDER
- Adjust the BUSTER 150 light so as not to dazzle other road users. The light must be firmly attached to the bicycle and the light cone must not be obstructed by anything.
- Adjustable in the range of 360
MOUNTING
SILICONE BRACKET
Adjust the BUSTER 150 so that it does not blind other road users. The
BUSTER 150 must be securely attached to the bike and light distribution must
not be obstructed
**
**
- SIGMA-ELEKTRO GmbH
- Dr.-Julius-Leber-Straße 15
- 67433 Neustadt / Weinstraße
- Germany
- Tel. +49 6321-9120-118
- kundenservice@sigmasport.com
VIDEO TUTORIALS
Detailed tutorials and application tips can be found at this link.
5 MODES
MODE MEMORY FUNCTION
After turning off the BUSTER 150 light the last used mode is retained.
PRESET MODE PROFILES
PROFILE SELECTION
You can adapt your BUSTER 150 individually to your requirements. For this
purpose, the lamp has 5 different profiles that you can select as follows.
Hold down the ON/OFF button for longer than 5 seconds when it is switched off,
then you will get to the profile selection. The lamp fl ashes once for profile
1, twice for profile 2, and so on. To select the desired profile, press the
ON/OFF button once. Your selection is confirmed by four short fl ashes of the
front LED.
BATTERY INDICATOR
NOTE: If the battery capacity is less than 20 %, the red indicator LED lights up and after about 45 minutes, the red LED begins flashing, and the BUSTER 150 goes out completely shortly thereafter
CHARGING
- Charge the light only if the ambient temperature is between +10 °C and +45 °C (50 °F and 110 °F). This protects the battery from damage and increases its service life.
- Ensure that the USB sealing marked red is always closed correctly after charging
- No energy can be transferred out through the USB-C connection.
CHARGING INDICATOR
TECHNICAL DATA
- Charging Temperature: +10°C to +45°C 50 °F and 110 °F
- Battery Type: 3.7 V, 1000 mAh
- Max power: 2 W
- Water and Dust rating: IP44
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>