SUNNY HEALTH FITNESS CB110 Bike Cadence User Manual
- June 8, 2024
- SUNNY Health Fitness
Table of Contents
SUNNY HEALTH FITNESS CB110 Bike Cadence
PRODUCT INTRODUCTION
We thank you for choosing our SunnyFit Bike Cadence. Our product is developed to help track your cycling performance. Please keep this user manual for future reference.
PRODUCT ACCESSORIES
BASIC PARAMETERS
We value your experience using Sunny Health and Fitness products For assistance with parts or troubleshooting, please contact us at Support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).
REMOVE THE INSULATING SHEET BEFORE USING
Turn the battery cover counterclockwise toward a big circle to open it. Please
remove the insulating sheet before using it, then put the battery cover back
and turn clockwise toward a small circle to lock it.
Flashing Indicator Light
INSTALLATION
Attach the Flat Rubber Mat onto the back of the SunnyFit Bike Cadence then
secure it with Smal Band or Plastic Cable Tie onto the pedal crank.
APP CONNECT INSTRUCTION
- Scan the below QR code to download the SunnyFit APP.
- You can also download the SunnyFit APP from the App Store or Google Play Store.
- Rotate the pedal crank and search for the SunnyFit Bike Cadence using ANT+ or Bluetooth device. Follow the steps on the SunnyFit APP and choose the bike accordingly.
- Open the Sports page of the SunnyFit APP, go to the “workout” tab, and click the “Search” button to connect the SunnyFit Bike Cadence with the SunnyFit APP.
- After clicking the “Retry” button, you could see a scan dialog box, as shown below, then select the SunnyFit Bike Cadence.
- Click the ‘Choose Your Bike” button and choose the equipment accordingly. Then cuck the “Select” button to confirm.
NOTE:
If you select the “OUTD0OR BIKE” on the SunnyFit APP. the SunnyFit Bike
Cadence would change to Speed mode. Please remove the SunnyFit Bike Cadence
from the pedal crank. Attach the Curved Rubber Mat onto the back of the
SunnyFit Bike Cadence, then secure the SunnyFit Bike Cadence with Large Band
or Plastic Cable Tie onto the flywheel axle.
DISCLAIMER
- The information in this manual is for reference only. This product may be subject to change based on the manufacturer’s research and development without notice.
- We shall not make any statement or warranty about this manual or the product.
- We shall not bear any legal responsibility for any direct or indirect, accidental or special damages, losses, and expenses arising from or it connection with this manual or the product.
FCC STATEMENT
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
CONNECT WITH US
FOR FITNESS ARTICLES, VIDEos & WORKOUTS.