MG Tech CDC-F1 15W Fast Wireless Car Charger User Manual
- June 8, 2024
- MG Tech
Table of Contents
CDC-F1 15W Fast Wireless Car Charger
User Manual
Product Features
- Physical button and LED indicator on both sides.
- Built-in 2 coils and cooling fan, the two arms and feet will automatic closing when put the phone on the charge,it support wireless charging for Qi-enabled smartphones.
- Adjustable feet suitable for different size phones,anti-slip silicone on both arms and feet,Type-C charging port.
- Built-in stepper motor, it works with low noise.
- NPO capacitors,lower charging temperature and high charging efficiency.
- Standby mode: the green indicator lights on both sides keeps on.
- Charging mode: the LED indicator lights on both sides keep blue, it turns green once remove the receiver.
- FOD function: when put metal or magnet objects on the charge, the blue and green LED indicator light will flash for reminding.
- Perfect protective function based on over-voltage, over-current, over-temperature and short-circuit protection.
Specifications
| Input | DC5V/2A, 8V-3A |
|---|---|
| Output | 15W/10W/7.5W/5W |
| Product Standard | Qi |
| Charging Distance | ≤10mm |
| Charging Efficiency | ≤80% |
| Product Dimension | Ø72.5.73.109mm |
| Product Material | ABS+PC |
Fastasicalass charging requires quick 18W or 18W above adapter.
Product Parts Description
Product Operating Guide
- Please make sure the product connect to the power before using.
- The green LED indicator light on if connected with power.
- The LED indicator light will flashes and the product stop charging when the current is too large or there is foreign object. Do not wireless charging the phone if similar situation happened.
- Press the power button to open the two arms and place phone on the charge, that the phone will start wireless charging and the two arms locking automatically. Only need to press the pm.a button to release two arms if you want to take out the phone.
- Please purchase the wireless receiver module or case separately (Not included in the product) if your phone do not support wireless charging.
Attention
- Please do not vigorously extrude or collide.
- Please do not dismantle or put it into fire or water when the product is power on,to avoid short circuit or leakage.
- Please do not use it in severely high temperature,high humidity or corrosive environment,to avoid damage to the circuit leakage.
- Please do not put the magnetic strip or chip card (Such as ID card,bankcard etc.)on the charging pad to avoid to cause magneticcard lose efficacy.
- Please do not put the metal (Such as coin etc.) on the charging pad when charging,to avoid damage from heating.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.