LINEAR DNT00094 Garage Door Keypads Instruction Manual
- June 8, 2024
- LINEAR
Table of Contents
DNT00094 NMTK
Installation / Programming Instructions
DESCRIPTION
This wireless keypad is a wireless radio control designed for use with
automatic garage door and gate operators. The radio format provides
unparalleled security with more than a million different codes. In operation,
the user enters their unique code on the unit’s keypad (1 to 6 digits long)
and presses the button to activate the door operator. For up to 30 seconds
after the last activation, the keypad can be
re-triggered by simply pressing the button again. This allows the user to stop
or reverse the opener quickly, without having to re-enter their code.
The keypad has built-in keypad lighting for use at night or in dark areas. The
clear silicone keys are backlit with a soft blue glow. Press the button at any
time to activate the keypad backlight.
To turn the overhead operator light on or off, enter the user code, then press
the button.
The keypad lockout timer will disable the keypad after 10 activations. The
keypad must remain idle for 30 seconds before new attempts. The receiver is
programmed by sending a signal from the user’s transmitters that stores the
transmitter’s code into the receiver’s memory. The receiver will retain its
memory even without power and will only activate from these “memorized”
transmitters. Each keypad code can be considered a different transmitter. Each
receiver can remember a maximum of 10 transmitter codes. Any combination of
portable transmitters and keypad codes up to the maximum number can be
entered.
COMPONENTS
KEYPAD FEATURES
PROGRAMMING OPERATORS
-
Refer to the instructions provided with the garage door opener to set it into “learn” mode.
Press the opener’s LEARN BUTTON for 1 second and release. The opener should BEEP and the LIGHT should BLINK once. The RED LED will remain lit in Learn Mode for 15 seconds. -
While the RED LED is lit, enter a 1-6 digit code into the keypad. Then PRESS and HOLD the keypad’s key until the opener BEEPS and the light BLINKS once.
Repeat Steps 1 & 2 for any additional keypad codes.
DELETING A KEYPAD CODE
To delete a keypad code that you no longer want follow the same steps above.
The opener will recognize the code and delete it from memory. The RED LED and
LIGHT will blink 4 times to show the code was successfully deleted.
WALL MOUNTING
MOUNT THE KEYPAD IN CLEAR VIEW OF THE
DOOR WITH THE TWO SCREWS SUPPLIED
Slide battery cover open and remove batteries to access mounting hole. Replace batteries and slide battery cover closed after mounting.
KEYPAD OPERATION
DOOR OPERATION
- ENTER USER KEYPAD CODE
- PRESS
NOTE: PRESS BUTTON TO TURN KEYPAD BACKLIGHT ON FOR NIGHTTIME OPERATION
NOTE: TO STOP OR REVERSE THE OPENER, THE BUTTON CAN BE PRESSED AGAIN FOR
UP TO 30 SECONDS WITHOUT RE-ENTERING THE CODE
OVERHEAD LIGHT OPERATION
- ENTER USER KEYPAD CODE
- PRESS
NOTE: THE OVERHEAD LIGHT CANNOT BE OPERATED FROM THE KEYPAD UNLESS THE DOOR IS OPEN
CHANGING BATTERIES
Follow the steps in the diagram and use caution to keep batteries away from
children.
Operation requires 3 AM alkaline batteries. Properly dispose of old batteries.
Many electronic stores and supermarkets have battery recycling bins. Alkaline
batteries can be safely disposed of with normal household waste. Never dispose
of batteries in fire because they could explode.
LIMITED WARRANTY
This product is warranted to the original consumer against defects in material and workmanship for the periods mentioned above. Nortek Security & Control, LLC will repair, or at its option, replace, any device that it finds requires service under this warranty. This warranty does not apply to damage to the product from negligence, abuse, abnormal usage, misuse, accidents. normal wear or tear or due to failure to follow Seller’s instructions, or arising from improper installation, storage or maintenance. In no event will Nortek Security & Control, LLC be responsible for incidental, compensatory, punitive. consequential, indirect. special or other damages. The remedies provided by this warranty are exclusive. Some states do not allow the exclusion or limitation of incidental and consequential damages, so the above limitation or exclusion may not apply to you. Any warranties implied by law are limited to the time periods set forth above. Some states do not allow limitations on how long an implied warranty lasts. so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. For warranty service, contact Nortek Security & Control LLC at www.nortekcontrol.com. In order to be protected by this warranty, save your proof of purchase should repair be required.
IMPORTANT: Radio controls provide a reliable communications link and fill an important need in portable wireless signaling. However, there are some limitations which must be observed.
- For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range.
- A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.
- Changes or modifications to the device may void FCC compliance.
- Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
- A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.
WARNING: Changes, modifications or adjustments not expressly approved by
manufacturer could void the user’s authority to operate this equipment. There
Are No User Serviceable Parts.
NOTICE: This device complies with part 15 of the FCC rules and with
Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.