Alpine KIT-F9ID Halo 9 installation kit for Iveco Daily 6 and 7 Instruction Manual

June 8, 2024
Alpine

Alpine-LOGO

Alpine KIT-F9ID Halo 9 installation kit for Iveco Daily 6 and 7

Alpine-KIT-F9ID-Halo-9-installation-kit-for-Iveco-
Daily-6-and-7-FIG-19

Model : Daily VI & Daily VII
Year: Daily VII > 2019 & Daily VI > 2014
Kit content : double DIN facia plate; mounting brackets + screws; SWRC CAN bus & LIN bus wiring harness; antenna adapters; camera adapter; USB/AUX adapter; speaker adapter

Content and wiring harness connections

Alpine-KIT-F9ID-Halo-9
-installation-kit-for-Iveco-Daily-6-and-7-FIG-1

  1. A/1B – to RADIO connectors

  2. to CAR connector

  3. CAMERA input

  4. AUX input

  5. CAMERA control/REMOTE out

  6. POWER ANTENNA output

  7. to optional/extra SERVICES:
    Orange – Reverse output
    Green – Speed output

  8. to INTERFACE connector

  9. to LIN BUS – (point 7 / page 4-5)

  10. External power access

  11. SPEAKER connection (point 9 / page 9)

  12. CAN BUS access – (point 7 / page 4-7) 13 – FAKRA antenna adapter

  13. ISO/DIN antenna adapter

  14. USB/AUX adapter

  15. CAMERA input adapter
    OPTIONAL 1 →(point 7 / page 5) OPTIONAL 2 →(point 9 / page 9)

  16. This is how the original dashboard looks like.

  17. Remove the drawer and unscrew the two screws as shown in the picture.

  18. Remove the rubber compartment as shown in the picture.

  19. Unscrew the central screw and remove the original facia.

  20. Remove and save the 4 screws circled in the pictures.

  21. Connect the harness as indicated on left side (page 2).

  22. Set the harness according to the configuration of your vehicle – Iveco Daily VIIAlpine-KIT-F9ID-Halo-9-installation-kit-for-Iveco-Daily-6-and-7-FIG-4 Set the harness according to the configuration of your vehicle – Iveco Daily VIAlpine-KIT-F9ID-Halo-9-installation-kit-for-Iveco-Daily-6-and-7-FIG-5

  23. Steering wheel remote controls functions Iveco Daily VII steering wheel remote controls functions.

  24. Volume

  25. Mut

  26. Volume

  27. Seek

  28. Source

  29. Seek –

  30. Accepting incoming call

  31. Voice
    Iveco Daily VI steering wheel remote controls functions.Alpine-KIT-F9ID-
Halo-9-installation-kit-for-Iveco-Daily-6-and-7-FIG-7

  32. Mute

  33. Volume +

  34. Volume –

  35. Source

  36. Accepting incoming call/Voice

  37. Seek +

  38. Seek –

  39. Reject incoming call

  40. Pair your phone and make a call.
    If you hear the audio from WRONG SPEAKERS →install OPTIONAL 2 (see page 2 point 11).

  41. Take the left and right brackets and fix them with the supplied screws as shown in the picture. Connect the harness as indicated

  42. Make all connections, check the proper functioning of the whole system and fix the head unit with the OEM screws as shown in the picture.

  43. Fix the metal bracket with the supplied screw as shown.

  44. Place the metal bracket at point “A” and push the facia plate towards the dashboard “B” as shown in the picture.

  45. Adjust the height of the monitor and fix it as shown in the picture.

  46. Fix the monitor by fixing the 4 screws as shown in the figure.

  47. Install the plastic cover as shown in the picture.

  48. This is the final result.

  49. Access the interface radio setting menu as shown in the pictures.

  50. Access the interface radio setting menu as shown in the pictures. CAN / LIN Activity (Yes / No)
    If the CAN / LIN connection to the vehicle is correct, display shows “Yes“.

  51. Access the interface settings as shown in the pictures.

    • Ignition Logic (only if supported by vehicle)

    • Switch between Key and Door

    • Key = the radio switches on automatically when the key is turned in the ignition lock

    • Door = the radio switches on automatically when the central locking (must be supported by the vehicle) of the door is opened (PRE-ignition)

    • Ignition HOLD Minutes

    • Adjustable between 0 and 30 min(s)

    • The radio “runs on” the set time (0 to 30 min(s)) when the ignition is switched off from the vehicle / radio

    • Reverse Logic

    • Switch between Natural and Delayed

    • Natural = Switches the reversing signal with activation / deactivation of the reverse gear immediately ON / OFF

    • Delayed = Switches the reversing signal with activation / deactivation of the reverse gear with a delay ON / OFF

    • Reverse ON HOLD Seconds (0 to 30sec(s))

    • When you are engaging the reverse gear, the interface will trigger the reverse to the radio after the time period (0 to 30sec(s)) specified in the menu.

    • Reverse OFF HOLD Seconds (0 to 30sec(s))

    • When you are removing the reverse gear,the interface will remove the reverse to the radio after the time period (0 to 30sec(s)) specified in the menu.
      (The camera image of the rear-view camera is displayed accordingly longer.)

    • Button Illumination (only X903D-ID/X903DC-F)

    • Switch the button illumination:
      Orange, Dim Orange, Yellow, Dim Yellow, Red, Dim Red, Green, Dim Green, Blue, Dim Blue, White, Dim White

    • Preflight Check (menu item not available)

    • Driver receives notification before start if equipment is secured

    • Button Configuration (only X903D-ID/X903DC-F)

    • Configures the respective key assignment depending on the installed position of the keys (not used)

    • Steering Wheel (only X903D-ID/X903DC-F)

    • Switchable between Left (default) and Right

    • Factory Settings

    • Resets all interface settings

  52. Connectivity LayoutAlpine-KIT-F9ID-Halo-9-installation-kit-for-Iveco-Daily-6-and-7-FIG-18

Documents / Resources

| Alpine KIT-F9ID Halo 9 installation kit for Iveco Daily 6 and 7 [pdf] Instruction Manual
KIT-F9ID Halo 9 installation kit for Iveco Daily 6 and 7, KIT-F9ID, Halo 9 installation kit for Iveco Daily 6 and 7, kit for Iveco Daily 6 and 7
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals