PYLE PJAZZGT88BR 6 String Semi-Hollow Body Jazz Style Electric Guitar User Guide

PJAZZGT88BR 6 String Semi-Hollow Body Jazz Style Electric Guitar
User Guide

6 String Semi-Hollow Body Jazz Style Electric Guitar
with Accessory Kit
USER GUIDE

PJAZZGT88BR 6 String Semi-Hollow Body Jazz Style Electric Guitar

Please take a few moments to read through this manual. It will provide you with answers to many of your questions as well as inform you about the care and maintenance of your new instrument.
GUITAR ANATOMY

CLEANING

Cleaning your guitar regularly is one of the best ways to maintain the finish and prolong string life. Clean your guitar after each use, making sure to wipe the fingerboard and  strings as well as any of the plated parts such as tuners, pickups, bridge etc. Make sure to remove all perspiration, as it can lead to corrosion and rusting in metal hardware and strings.

TUNING YOUR GUITAR

Tune your instrument using the tuning keys to raise or lower the pitch.
On a guitar with a locking tremolo system, you must first loosen the locking nut before you can adjust the tuning with the tuning machines. Although locking tremolo systems  have fine tuners located on the bridge, they only allow limited (fine) tuning. Counter-clockwise rotation of the tuning keys will raise the pitch of the string while  clockwise rotation will lower the pitch of the string you are tuning. Tune your guitar starting with the lowest to highest strings. After you have done this once, go back and  double-check the tuning again. On some instruments you will have to do this a few times, especially if the strings are new or you have a guitar with a fioating tremolo bridge.  Tuning one string may afiect the other strings and it is necessary to recheck the tuning until all strings are staying at the desired pitch.

Note: New strings tend to stretch and detune until they settle. It is a good idea to stretch the strings when you have just put on a new set. Do this after the initial tuning by  bending notes and physically stretching each string by pulling away from the fingerboard (be careful no to pull too hard as you may break a string that way). After thoroughly stretching the strings repeat the tuning process.

CHANGING STRINGS

We strongly recommend that you change your strings fairly often. If you play daily, we recommend that you change your strings every 3 months. A new set of strings will  sound clear and precise, while an old set will sound dull and can produce unusual buzzing and dead notes. If you notice that your strings have become dirty, discolored, or  produce an unusual buzzing or dull sound, then it is definitely time to put a new set of strings on your guitar.
Always check your new strings and make sure they are smooth and free of defects before installing them. If there are any irregularities, such as kinks, twists, or any other  manufacturing defects, they will cause buzzing and untrue notes as well as sound distortion. We recommend replacing one string at a time, so that all the tension is not taken  off of the neck. This will make it easier to re-tune and setup the neck.

When winding strings on to the tuning machine post, always wind them tightly and evenly to avoid any slipping than can occur if there are any gaps. Always use at least 2 or 3  winds around the post starting from top to bottom.
As a rule of thumb, use about and extra 5cm (2 inches) of slack when restringing a guitar and about 8cm (3 inches) of slack when restringing a bass. For unwound, or plain  strings, follow the diagram (Figure 1) detailing how to install these strings on to the post to prevent them from slipping.

1. Insert end of string into tuning post (make sure to leave enough slack for a few wraps around the post).
2. Wrap end of string clockwise around post and under the string where it goes into the post (counterclockwise when stringing tuners on treble side of headstock).
3. Pull end of string tight over itself making a sort of knot (end of string may then be bent down and cut off cleanly near knot).
4. Tune to pitch, making sure the wraps wind neatly down the tuning post.

Note: Strings are always wound clockwise around the posts on the bass side and counter-clockwise around the posts on the treble side of headstock.

FLOATING BRIDGE ADJUSTMENT
A floating bridge has an arched wooden or metal base held in position on the instrument top only by the downward pressure of the strings. If the bridge is moved even  slightly while re-stringing, the intonation will no longer be true (some instruments feature “pinned” bridges that eliminate this possibility).
To adjust fioating bridge intonation on a guitar, first check the 12th-fret harmonic and the fretted 12th-fret tuning of both E strings (high and low).
If properly intonated, the fretted and harmonic 12-fret pitches of both
E strings will agree, with none of them being sharp or flat.

If the pitch of the 12th-fret note is sharp relative to the pitch of the 12th- fret harmonic, lightly tap the foot of the bridge to move it back toward the tailpiece until both  pitches agree. If the pitch of the 12th-fret note is fiat relative to the pitch of the 12th-fret harmonic, lightly tap the foot of the bridge to move it forward toward the neck  until the two pitches agree. To fine-tune fully adjustable bridges, adjust each saddle forward or back using the individual intonation screws while checking the tuning of the  12-fret harmonic against the fretted 12th fret pitch.
IMPORTANT NOTE: When re-stringing a guitar with a fioating bridge, change strings one at a time. Do not remove all the strings at once, as the bridge is held in the correct position only by the downward pressure of the strings.

ADJUSTING THE TRUSS ROD
To adjust the truss rod, first locate the truss rod access at the headstock (Figure 2) or end of neck by body joint (Figure 3), remove the truss rod cover, and insert the correct  size allen wrench (4mm) or pipe wrench (8mm) to adjust. Turn counter-clockwise to loosen and clockwise to tighten.

Note: If your truss rod nut access is not visible, it is possible your instrument has it located inside of the neck pocket (Figure 4) – this will require the neck to be taken off of the body to adjust the truss rod.
Truss rod adjustments should only be performed by a qualified technician.
Improperly adjusting or over adjusting the truss rod can result in damage to the guitar neck and is not covered under the warranty.

CONTROLS AND SPECS
The following are some brief descriptions of the basic electronic controls and terminology. For more specific information on your model please visit our website at www.PyleUSA.com.
Note: Most control knobs are easily tightened or removed by using a 2.0mm allen wrench or fiathead screwdriver to adjust the set screw on the side of the knob. If a knob  becomes loose, you should first remove the knob and check the control to make sure It Is properly tightened to the body before re- tightening the knob onto the control  shaft. A loose control shaft can easily be tightened using any adjustable wrench. You will need to remove the electronics backplate and hold the control from the back of the  guitar while tightening the nut from the top of body. This will ensure that you do not move the controls or damage/break any of the wire connections.

Volume Control
Controls the master output level of the guitar. Turning the knob clockwise will increase the volume while turning counter- clockwise will decrease the volume. Some  instruments will have multiple volume controls in which case, you’ll and there’s a volume control for each pickup.
Note: In the case of multiple volume controls, when either volume control is turned off and the pickup selector switch is in the middle position w/both pickups on, the entire signal of the instrument will be turned off.
Tone Control
This adjusts the high frequencies present in the signal coming from your guitar. With the knob turned fully clockwise, all frequencies are present. Turning the knob counter-clockwise decreases the high frequencies.
Output Jack
This is where the output signal of the guitar is sent to the amplifier by plugging in any standard 1⁄4” guitar cable. Most output jacks are located near the bottom corner of the guitar below the electronics cavity.
Note: If your guitar has active electronics, you should always remove your cable after playing. Leaving your cable plugged into your instrument will drain the battery.
If your jack ever comes loose, do not tighten it without first removing the jackplate and securing the inside of the jack, otherwise you may break the wires causing your guitar  to lose output.

Pickups
The pickups on your guitar turn the string vibrations into an electronic signal that is sent to your amplifier. Pickups are made up of magnets and coils of wire.
There are 2 types of magnetic pickups used in most electric guitars – Single Coils and Humbuckers. A Single Coil pickup is made up of only 1 coil of wire and generally has a
weak output.
Due to its construction, a single coil will be noisy since it cannot block hum and RF interference. Humbuckers on the other hand are in fact “hum-cancelling” because of their construction using 2 coils side by side. The signals from each coil are combined in a certain way that cancels the hum and RF interference that is common with single  coil pickups. Humbuckers generally have a higher output signal compared to single coils.

Pickup Selector Switch
The selector is used to switch between difierent pickups or combinations of pickups (on guitars with two or more pickups).

GUITAR AMP SETTINGS GUIDE
STEP 1 HOW TO EQ A GUITAR AMP  UNDERSTANDING THE CONTROLS
The basic controls in the guitar amps include;

The ‘Gain’ Knob
This knob controls the amount of distortion which is featured on the amp. If you keep this control low, your guitar tone will have little to no distortion, if it’s set high your guitar will be more distorted.
The ‘Bass’ Knob
This controls the amount of ‘bass’ in your guitar sound. If you want your guitar to sound warm and thick, turn this control up. Too much bass can often lead to your guitar sounding muddy, so make sure that you use this control sparingly.
The ‘Middle’ Knob
This controls the amount of ‘mids’ in your guitar tone. The more mids you have, the more you will stick out in a band mix.
The ‘Treble’ Knob
This controls how bright your guitar sounds. If you want your guitar to sparkle, turn this knob up. If you seek warmer tones, try bringing this knob down.
The ‘Presence’ Knob
The presence knob starts where the treble knob stops. It’s essentially like a ‘super treble’ control. This is perfect for country guitar or spanky funk lines.

The ‘Master Volume’ Knob
The ‘master volume’ knob controls how loud or quiet your amp is. Make sure this knob is always cranked! These controls are usually found on the front or top of the guitar amplifier, like this:

STEP 2 HOW TO EQ A GUITAR AMP – DIALLING IN THE PERFECT GUITAR TONE

Tip #1 Set All The Controls To 12 o’ Clock
When setting up your guitar amp, the first thing you should do is set all of your controls to 12 o’clock. Setting everything at 12 o’ clock gives you a great starting point, from here it’s easy to tweak your amp to where you want it.
Tip #2 Gradually Tweak Each Control On Your Amp
When you EQ your amp, make sure that you spend some time on each control. Don’t just dive straight into adjusting every single knob, pick one control and gradually turn it until you are happy with your guitar tone.
Tip #3 Don’t Crank The Gain Knob
One of the biggest mistakes that beginners make is cranking the gain knob. Cranking the gain knob on the amp will just turn your guitar to mush. Sure, it can be fun and  there’s nothing wrong with having a great crunch tone. However, it’s important to be modest with the gain knob. The level of your gain knob is something that you should  definitely be aware of when learning how to EQ a guitar amp.

STEP 3 HOW TO EQ A GUITAR AMP – 3 ESSENTIAL AMP SETTINGS THAT WILL MAKE YOU SOUND AMAZING
If you’re interested in getting some great amp settings, there are 3 essential tones that you’ll need. These are:

Questions? Comments?
We are here to help!
Phone: (1)718-535-1800
Email: support@pyleusa.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>