SEAGWAY KS0007 Kick Scooter User Manual
- June 8, 2024
- SEAGWAY
Table of Contents
KS0007 Kick Scooter
User Manual
KS0007 Kick Scooter
The manufacturer reserves the right to make changes to the product, release firmware updates, and update this manual at any time. Visit ap- en.segway.com or check the Segway-Ninebot app to download the latest user materials. You must install the app, activate your KickScooter, and obtain the latest updates and safety instructions.
Diagram and Functions
Handlebar Functions
Power Button| Power on/off| Press the Power Button to power on the scooter. Press and hold to power it off.
- Only available when the scooter is not locked via the Segway-Ninebot app.
---|---|---
Wake up the screen| Press the Power Button to wake up the screen when the screen automatically dims.
Mode Switching Button| Switch between speed modes| Press the Mode Switching Button twice to switch modes.
Multi-function Button| Turn on/off the cruise mode| Press the Multi-function Button to turn on the cruise mode, press again to turn it off. - Enable the cruise mode via the Segway-Ninebot app.
Turn on/off the headlight| Rotate the Multi-function Button clockwise/counterclockwise to turn off/on the headlight.
Turn on/off the Adaptive headlight feature| Rotate the Multi-function Button clockwise/counterclockwise and hold it for 3 seconds to turn off/on the Adaptive headlight feature. When the scooter is activated, this feature is turned on by default.
Confirm the password| Press the Multi-function Button to confirm the password after inputing the password with the Turn Signal Button successively.
USB Port| Charging| Connect your device to the USB Port.
Throttle| Turn on the assist mode| Press and hold the throttle for 5 seconds to turn on the assist mode. Squeeze the brake lever to turn it off.
Speed up| Press and hold the throttle to speed up.
NFC Area| Interact with the NFC card to Power on/off| Tap the NFC card on the NFC Area to Power on/off.
Interact with the NFC card to unlock| Tap the NFC card on the NFC Area to unlock the scooter.
Horn Button| Turn on the horn| Press the Horn Button, the scooter will beep.
Turn Signal Button| Turn on the left/right signal| Press the left/right side of the Turn Signal Button, the left/right turn signal will flash, and automatically turn off after 5 seconds.
Input the password| Press the left/right side of the Turn Signal Button (left is minus, right is plus) to input the password. The password is set to 1-2-3-4 by default. Change it via the Segway-Ninebot app.
Dashboard
Symbol | Name | Meaning | Description |
---|
| POWER
Progress Bar| The symbol displays the motor output power of the scooter.
| Speedometer| The symbol displays the current speed of the scooter.
| Cruise Mode| The symbol indicates that the Cruise mode is activated.|
Enable the cruise mode via the Segway-Ninebot app:
- In ECO, DRIVE or SPORT mode, press the Multi-function Button to activate
the cruise mode when the speed > 3.1 mph (5 km/h). Then the scooter will
cruise at the current speed.
Note: When the cruise mode is activated, the scooter will beep and the front and rear turn signal will flash once respectively.
2) Turn off the cruise mode with the following methods: Method 1: Twist the throttle or squeeze brake levers. Method 2: Press the Multi-function Button. Method 3: Switch the speed mode.
| Lock| When the icon lights up, it means the scooter is locked.|
When the scooter is locked via the Segway-Ninebot app:
- The alarm will automatically enter to standby mode when the scooter is
powered off after 30 seconds.
2) When the alarm is trigged, the scooter will start beeping and flashing lights. At this point, the motor is locked automatically. Unlock the scooter with the following methods: - Press the Power Button to wake up the screen, the dashboard displays the
digit “0” by default, then input the four-digit password 1-2-3-4 with the Turn
Signal Button and confirm the password with the Multi-function Button
successively.
Note: Change the password via the Segway-Ninebot app.
2) Tap the NFC card on the NFC Area.
3) Unlock via the Segway-Ninebot app.
Symbol | Name | Meaning | Description |
---|---|---|---|
Temperature Warning | It indicates that the battery temperature has reached |
60°C (140°F) or is below 0°C (32°F).
| USB Port Icon| The symbol indicates that the device is connected to the USB port.
| Bluetooth| It indicates that the scooter is connected to the Segway-Ninebot app.
| Warning| The symbol indicates that the scooter has detected an error. The
error code will display on the dashboard. See page 7 for possible causes.
| Battery Level| The symbol displays the remaining battery power in battery
bar.
| **** Adaptive Headlight| When the icon flashes, it means the Adaptive
headlight feature is turned on. At this point, the headlight works
automatically to adapt to a variety of situations and conditions and help
illuminate the way.
Speed Modes Introduction
Mode/model| P65U (Speed limit)| P65A (Speed limit)|
Switching methods
---|---|---|---
| 3.7 mph (5 km/h)| 3.7 mph (5 km/h)| **** Turn on/off the WALK
mode via the Segway-Ninebot app. Note: The headlight is always on and the tail
light will keep flashing in WALK mode.
| 0-3.7 mph
(0-5 km/h)| 0-3.7 mph
(0-5 km/h)| **** Turn on the ASSIST mode via the Segway-Ninebot app: Press
and hold the throttle for 5 seconds to activate the assist mode. Squeeze the
brake lever to turn it off.
**_PARK**_
| 0 mph (0 km/h)| 0 mph (0 km/h)| The scooter will automatically enter to PARK mode in the following circumstances:
- The rider stops riding and the scooter is at a complete stop.
2) The start speed ≤ 1.24 mph (2 km/h).
Note: The start speed is set to 3 km/h by default, only available to change via the Segway-Ninebot app (0.62-3.1 mph [1-5 km/h]).
Exit the PARK mode: - The scooter remains still after squeezing the brake lever for 5 seconds.
2) Press and hold the throttle till the speed ≥ 2.49 mph (4 km/h).
ECO
| 9.3 mph (15 km/h)| 9.3 mph (15 km/h)| **** Press the Mode Switching Button twice.
DRIVE
| 21.7 mph (35 km/h)| 15.5 mp (25 km/h)| **** Press the Mode Switching Button twice.
SPORT
| 21.7 mph (35 km/h)| 15.5 mp (25 km/h)| Press the Mode Switching Button twice.
Specifications
Item | Parameter |
---|---|
**** Product | Name |
Model | P65U |
Length × Width × Height | Approx. 46.9 × 26.9 × 47.8 in (1190 × 684 × 1214 mm) |
Folded: Length × Width × Height | Approx. 46.9 × 26.9 × 22.3 in (1190 × 684 × |
567 mm)
Net Weight| Approx. 25.9 kg ( 57.1 lbs)
Rider| Max. Payload| 120 kg (265 lbs)
Recommended Age| 18–60 years old
Required Height| 3’11”–6’6”(120–200 cm)
Machine| Wheelbase| 35.6 in (903 mm)
Ground Clearance| 3.1 in (79 mm)
Max. Speed| Approx. 21.7 mph (35 km/h)
Design Speed| Approx. 23.0 mph (37 km/h)
Typical Range[1]| Approx. 40.4 miles (65 km)
Max. Slope| Approx. 22%
Traversable Terrain| Bicycle lanes, parks, campuses and most of the flat road
conditions and typical Belgian roads
Operating Temperature| -10–40°C (14–104°F)
Storage Temperature| -10–50°C (14–122°F)
IP Rating| IPX5
Duration of Charging (single)| Approx. 4.5 h
Battery| Nominal Voltage| 46.8 V
Max. Charging Voltage| 54.6 V
Nominal Energy| 561 Wh
Nominal Capacity| 12 Ah
Charging Ambient Temperature| 0–45°C (32–133°F )
Battery Management System| Over-heating, short circuit, over-current, over-
discharge and over-charge protection
Motor| Motor Type| Brushless DC (BLDC) motor
Nominal Power| 0.5 kW, 500 W
Max. Power| 0.98 kW, 980 W
**** Charger| Input Voltage| 100–240 V 3A
Max. Output Voltage| 54.6 V
| Item| Parameter
---|---|---
Charger
| Output Power| 0.1 kW, 162 W
Rated Output| 48 V
**** Tire| Type| 10.5-inch Self-sealing tubeless tires
Tire Pressure| 30–35 psi
Material| Rubber
Others
| Speed Modes| WALK mode, ASSIST mode, PARK mode, ECO mode, DRIVE mode and
SPORT mode
Brake System| Disc brake & Electric brake
[1]: Typical Range: tested while riding with a full battery, 75 kg (165 lbs)
load, 25°C (77°F), at the speed of 9.9 mph (16 km/h) on average on pavement.
- Some of the factors that affect range include speed, number of starts and stops, ambient temperature, etc.
Common Failures Error code| Possible causes
---|---
10| BLE Bluetooth communication error
11| Motor 1A phrase current sampling failure
12| Motor 1B phrase current sampling failure
13| Motor 1C phrase current sampling failure
14| Throttle Hall sensor abnormality
15| Brake Hall sensor abnormality
18| Hall sensor abnormality
21| BMS communication error
22| BMS password error
23| BMS default serial number
24| System voltage detection abnormality
26| Flash storage error
27| Control board password error
28| Motor MOS driver upper bridge short circuit
29| Motor MOS driver lower bridge error
31| Program skip error
35| Vehicle default serial number
39| Battery temperature sensor error
41| Turn signal abnormality
42| Headlight abnormality
45| Abnormal bus current op-amp circuit
Certifications
This product is certified to ANSI/CAN/UL-2272.
The battery complies with UN/DOT 38.3.
The battery complies with ANSI/CAN/UL-2271.
Federal Communications Commission (FCC) Compliance Statement for USA.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide easonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Industry Canada (IC) Compliance Statement for Canada
This device complies with Industry Canada license-exempt RSS standard (s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interferencethat may cause undesired operation of the device.
CAN ICES-3 (B)/NMB-3(B)
Neither Segway Inc. nor Ninebot is responsible for any changes or
modifications not expressly approved by Segway Inc. or
Ninebot. Such modifications could void the user’s authority to operate the
equipment.
Model: P65U
FCC ID: 2ALS8-KS0007
IC: 22636-KS0007
Trademark
Segway, Segway KickScooter and the Rider Design are the trademarks of Segway
Inc.; Android is the trademark of Google Inc., App Store is a service mark of
Apple Inc. The respective owners reserve the rights of their trademarks and
copyrights, etc. referred to in this manual.
We have attempted to include descriptions and instructions for all the
functions of the KickScooter at the time of printing. However, due to constant
improvement of product features and changes of design, your KickScooter may
differ slightly from the one shown in this document. Visit the Apple app Store
(iOS) or the Google Play Store (Android) to download and install the Segway-
Ninebot App. Please note that there are multiple Segway and Ninebot models
with different functions, and some of the functions mentioned herein may not
be applicable to your unit. The manufacturer reserves the right to change the
design and functionality of the KickScooter product and documentation without
prior notice. (※The Segway-Ninebot App can support KickScooter with built-in
Bluetooth.
© 2022 Ninebot (Beijing) Tech Co. Ltd. All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>