PROGRESS LIGHTING P400323 Laila 4-Light Vintage Brass Coastal Chandelier Instruction Manual
- June 8, 2024
- PROGRESS LIGHTING
Table of Contents
PROGRESS LIGHTING P400323 Laila 4-Light Vintage Brass Coastal Chandelier
PACKAGE CONTENTS
HARDWARE CONTENTS (not actual size)
Safety Information
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main
circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified
electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture,
follow instructions carefully to assure full compliance with N.E.C.
requirements. If there are any questions, contact a qualified electrical
contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and
bulbs.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
- Install the chain holder (EE) onto the nipple (FF). Next, loosely thread the hex nuts (AA) onto the nipple (FF) and then thread this assembly onto the mounting strap (CC). Install this assembly to the outlet box using the mounting screws supplied with the outlet box (not included).
- In this step, you will adjust the depth of the chain holder in relation to the canopy depth. Take the canopy (HH) and slip it over the chain holder (EE). You will need to adjust the chain holder so at least 1/4″ of the threaded portion is exposed through the canopy hole. This is done by adjusting the depth of the nipple (FF) on the mounting strap (CC). When the chain holder (EE) is correctly adjusted, remove the canopy (HH) and tighten the top hex nut (AA) against the mounting strap (CC) and the bottom hex nut (AA) against the chain holder (EE).
- Pass the wires through the stem (C/D) and the chain loop assembly (E). Thread the stem (C) onto the fixture (A); Then thread stem (D) into the stem (C); Last thread chain loop assembly (E) to stem (D), secure them tightly. Slide the cage (B) onto the fixture (A) and hook it to the ends of the link (E).
NOTE: During this step, determine the hanging length of your fixture by
removing chain links (GG) and optionally cutting the electrical and groundwire
to length.
Do NOT cut electrical or ground wires until this overall length is determined.
Leave AT LEAST 6 inches MINIMUM of wire past the chain holder (EE) to allow
for easy connections in step 5. (Chain links can be spread open with 2 pairs
of pliers. Twist the split link ends in opposite directions and close by
squeezing them back together.)
Once hanging length is determined, open chain link at one end of chain (GG).
Hook the open chain link (GG) onto the fixture (A). Close the chain links back
together with the pliers. Open the quick link (JJ), attach the other end of
chain (GG) and chain holder (EE) onto the quick link (JJ), tighten the quick
link securely. You can now pass the wires through the fixture (A) and weave
them through every third chain link (GG). Continue to pass the wires AND chain
through the screw collar (DD) and canopy (HH).
Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB),
connect the RIBBED fixture wire to the WHITE supply wire from the outlet box;
connect the SMOOTH fixture wire to the BLACK supply wire. Connect the fixture
ground wire and supply ground wire using a wire nut or by fastening to the
ground screw on the mounting strap. Push all wire connections into the outlet
box.
Tuck the wires into the junction box and slip the canopy (HH) over the chain
holder. Thread the screw collar (DD) onto the chain holder to secure the
canopy tightly to the ceiling.
Thread the lamps (not included) into the fixture sockets. Use 60-watt MAX
incandescent candelabra base, SBCFL or SBLED.
WARRANTY AND EXCLUSIVE REMEDY:
Progress products, when properly installed and under normal conditions of use,
are warranted to our customers only to be free from defects in material and
workmanship at
time of shipment. All warranty claims must be asserted within one year from
date of purchase of the subject items; thereafter, warranty claims will not be
honored. Customers• sole remedy for a warranty claim or otherwise shall be
limited to repair or replacement of the subject product if it is shown to have
been defective in material or workmanship at time of shipment. Progress’s sole
and maximum liability for a defective product shall never exceed the cost of
the subject product. EXCEPT FOR SUCH A WARRANlY AND EXCLUSIVE REMEDY AS STATED
(AND THE EXPRESS WARRANlY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER
EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF
MERCHANTABILllY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE
LIABLE TO CUSTOMER IN WARRANlY, CONTRACT, NEGLIGENCE, STRICT LIABILllY OR
OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE
ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE
CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS. Therefore, the customer’s sole
and exclusive remedy against us for breach of the warranty, breach of contract
or negligence or strict liability or otherwise shall be limited to repair or
replacement of the subject product at our option (excluding installation and
removal charges which shall not be our liability) or, if we choose, refund of
the purchase price. In no case does our warranty and exclusive remedy extend
to anybody other than our customers. Our customers are not authorized to
extend warranties or remedies on our behalf to anyone. Such unauthorized
extensions of warranties or remedies by the customer shall remain customer’s
responsibility. Customer is responsible for determining the suitability of our
products for customer’s use or resale, or for incorporating them into objects
or for applications which customer designs, assembles, constructs or
manufactures.
Instructions d’Assemblage et Installation
Mise en garde: Lire les instructions avec soin et couper le courant au disjoncteur central avant de commencer !’installation.
MISE EN GARDE: Lire les instructions avec soin et couper le courant au
disjoncteur central avant de commencer !’installation.
MISE EN GARDE: Risque d’incendie. Min 90°C conducteurs d’alimentation.
Consulter un electrician qualifie pour assurer le bon conducteur de circuit de
derivation.
We can assist you with questions regarding product information, assembly or missing parts 80o-447-o573 @~ customerservice@progresslighting.com 8am-8pm (Eastern), Monday-Friday
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>