BLACK BOX LH1690C-LC-R3 Network Interface Adapter PCIE User Manual
- June 4, 2024
- BLACK BOX
Table of Contents
LH1690C-LC-R3 Network Interface Adapter PCIE
User Manual
ESD WARNINGS
ELECTROSTATIC DISCHARGES (ESD)
A sudden electrostatic discharge can destroy sensitive components. Proper
packaging and grounding rules must therefore be observed. Always take the
following precautions:
-
Transport boards and cards in electrostatically secure containers or bags.
-
Keep electrostatically sensitive components in their containers, until they arrive at an electrostatically protected workplace.
-
Only touch electrostatically sensitive components when you are properly grounded.
-
Store electrostatically sensitive components in protective packaging or on anti-static mats.
GROUNDING METHODS
The following measures help to avoid electrostatic damage to the device: -
Cover workstations with an approved antistatic material. Always wear a wrist strap connected to a properly grounded workplace.
-
Use antistatic mats, heel straps, and/or air ionizers for more protection.
-
Always handle electrostatically sensitive components by their edge or by their casing.
-
Avoid contact with pins, leads, or circuitry.
-
Turn off power and input signals before inserting and removing connectors or connecting test equipment.
-
Keep your work area free of non-conductive materials, such as ordinary plastic assembly aids and Styrofoam.
-
Use field service tools such as cutters, screwdrivers, and vacuum cleaners that are conductive.
SPECIFICATIONS
TABLE 1-1. SPECIFICATIONS
| SPECIFICATION | DESCRIPTION |
|---|---|
| Approvals | FCC Class B. CE. RoHS. EMAIL |
| Standards | IEEE 802.3z Gbit/s 1000BASE-X: |
IEEE 802.3x Full-Duplex Flow Control; IEEE 802.1Q VLANs
Connectors| (1) 850 nm LC Multimode
Fiber Cable Supported| 62.51125-pm, 501125 pm multimode
Indicators| LEDs on bracket: (1) Link/Act, (1) FDX
Data Transfer Mode| Full-duplex with flow control: 1000 Mbps speed
Bus Slot| PCI-e 1.1 compliant
Power| From the PCI-e bus; maximum 1.32 W +3.3 VDC at 0.4 A
Software Supported| Microsoft Windows XP, Vista, Server 2008/P2, Windows 7,
Windows 8/8.1, Server 2012; Novell Netware 5.x, 6.x Server;
Novell Netware DOS Client for ODI 16-bit;
NDIS2 driver Support DOS MS client, Lantastic, Lanman, Norton Ghost;
Linux driver for kernel up to 4.7;
FreeBSD 7.x and 8.0 driver
Dimensions| Card only: 4.5 x 2.75 in. (11.43 x 6.98 cm;) With bracket: 5 x
4.75 in. (12.7 x 12.06 cm)
Weight| 0.119 lb. (0.054 kg)
Environmental| Operating Temperature: 32 to 104° F (0 to 40° C);
Humidity: 5 to 90%
OVERVIEW
2.1 INTRODUCTION
The Network Interface Adapter PCIe 1000BASE-SX LC (LH1690C-LC-R3) is a Gigabit Ethernet Board that fully complies with all IEEE 802.3z and 1000BASE-X standards. Two LED indicators (LINK/ACT and FDX) on the bracket will help to oversee the board link, activities, and full-duplex status. The adapter has one 850-nm LC multimode fiber connector.
2.2 FEATURES
- Supports high-bandwidth 1000 Mbps network speed
- Complies with IEEE 802.3z 1000BASE-X fiber interface
- Operates in full-duplex mode
- Uses IEEE 802.3x full-duplex flow control
- Has (1) PCI-e bus, complies with PCIe rev 1.1 interface
- Supports jumbo frame
- Offers high-level VLAN filtering
- Supports IP headers and TCP/UDP checksums offload
- On-board screening of VLAN-tagged ethernet frames
- Supports Wake On LAN
- Complies with RoHS standard
2.3 WHAT’S INCLUDED
Your package contains the following item:
- (1) Network Interface Adapter PCIe 1000BASE-SX LC (LH1690C-LC-R3)
If this is missing or damaged, contact Black Box Technical Support at 877-877-2269 or info@blackbox.com
HARDWARE INSTALLATION
The following instructions apply to installing the Network Interface Adapter
PCIe in most systems. Refer to the manuals that were supplied with your system
for details about performing these tasks on your particular system.
To install the network adapter card, perform the following procedure:
WARNING : Before installing the adapter, make sure the system power is
OFF and unplugged from the power outlet, and that you have followed proper
electrical grounding procedures.
-
High voltage inside the system presents a safety hazard. Make sure the power is off before removing the cover.
-
Remove the system cover and select any empty PCIe slot. See Fig 3-1.
NOTE: If you do not know how to identify a PCIe slot, refer to your system documentation. -
Select an empty, non-shared PCIe slot and remove the faceplate. Keep the faceplate in a safe place. You may need it for future use.
NOTE: If you cannot locate or know how to find a PCIe slot, refer to the documentation that came with your system. -
Remove the Network Interface Adapter PCIe from the shipping package and store the packaging material in a safe location.
CAUTION: Wear a grounding device and observe electrostatic discharge precautions when installing the network adapter card in a system. Failure to observe this caution could result in damage to the card. -
Applying even pressure at both corners of the card, push the adapter card until it is firmly seated in the PCIe slot.
Make sure the card is securely seated.
-
Replace the system’s cover and secure it with the screws removed in Step 2.
-
Disconnect any personal anti-static devices.
-
Power the system on.
OPERATION
4.1 LED INDICATOR DESCRIPTION
The table below describes the LED indicators and their functions.
TABLE 4-1. LED INDICATORS
| LED | COLOR | FUNCTION |
|---|---|---|
| Link/Act | Green | Lights when cable connection is good and speed is 1000 Mbps. |
Blinks when traffic is present.
FDX| Green| Lights when the full-duplex mode is active.
4.2 WAKE ON LAN (WOL)
The Wake on LAN function on this adapter can recognize a wake-up frame and signal the PC to power up.
If the PC’s motherboard supports WOL and PCIe, the Wake up-Link connector is
not necessary).
To disable the WOL function (Default): Set WOL jumper (J1) to the OFF
position.
To enable the WOL function: Set the WOL jumper (J1) to the ON position.
CLIENT INSTALLATION
NIC CONFIGURATION
-
Enter into the operating system’s control panel.
-
From the Device Manager screen, configure the network adapters as shown in Figures 5-1 through 5-4.
-
Double-click on Realtek PCIe GBE Family Controller in the Device Manager screen.
-
The Properties screen appears.
4a. Select Shutdown Wake-on-LAN “Enabled“ as shown in Figure 5-2.
OR
4b. Select WOL & Shutdown Link Speed “No Speed Down“ as shown in Figure 5-3.
-
Select the Power Management Setting.
APPENDIX A: REGULATORY INFORMATION
FCC STATEMENT
Class B Digital Device. This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or telephone reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult an experienced radio/TV technician for help.
CAUTION:
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
To meet FCC requirements, shielded cables and power cords are required to
connect this device to a personal computer or other Class B certified device.
This digital apparatus does not exceed the Class B limits for radio noise
emission from digital apparatus set out in the Radio Interference Regulation
of Industry Canada.
APPENDIX B: DISCLAIMER/TRADEMARKS
B.1 DISCLAIMER
Black Box Corporation shall not be liable for damages of any kind, including, but not limited to, punitive, consequential, or cost of cover damages, resulting from any errors in the product information or specifications set forth in this document, and Black Box Corporation may revise this document at any time without notice.
B.2 TRADEMARKS USED IN THIS MANUAL
Black Box and the Black Box logotype and mark are registered trademarks of
Black Box Corporation.
Any other trademarks mentioned in this manual are acknowledged to be the
property of the trademark owners.
NOTES
NEED HELP?
LEAVE THE TECH TO US
LIVE 24/7
TECHNICAL
SUPPORT
1.877.877.2269
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>