PROGRESS LIGHTING P400320 5-LT Chandelier Installation Guide
- June 8, 2024
- PROGRESS LIGHTING
Table of Contents
PROGRESS LIGHTING P400320 5-LT Chandelier
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
- A Fixture 1
HARDWARE CONTENTS (not actual size)
Safety Information
Please read and understand this entire manual before attempting to assemble, operate or install the product.
CAUTION: Read instructions carefully and tum electricity off at main circuit breaker panel before beginning installation.
CAUTION: Risk of tire. Min. 90°C supply conductors. Consult a qualified electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and
bulbs.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
- Install the chain holder (EE) onto the nipple (FF). Next, loosely thread the hex nuts (AA) onto the nipple (FF) and then thread this assembly onto the mounting plate (CC). Install this assembly to the outlet box using the mounting screws supplied with the outlet box (not included).
- In this step, you will adjust the depth of the chain holder in relation to the canopy depth. Take the canopy (KK) and slip it over the chain holder (EE). You will need to adjust the chain holder so at least 1/411 of the threaded portion is exposed through the canopy hole. This is done by adjusting the depth of the nipple (FF) on the mounting plate (CC). When the chain holder (EE) is correctly adjusted, remove the canopy (KK) and tighten the top hex nut (AA) against the mounting plate (CC) and the bottom hex nut (AA) against the chain holder (EE).
NOTE: During this step, determine the hanging length of your fixture by removing chain links (GG) and optionally cutting the electrical and ground wire to length.
Do NOT cut electrical or ground wires until this overall length is determined. Leave AT LEAST 6 inches MINIMUM of wire past the chain holder (EE) to allow for easy connections in step 4.(Chain links can be spread open with 2 pairs of pliers. Twist the split link ends in opposite directions and close by squeezing them back together.)
Once hanging length is determined, open chain link at one end of chain (GG).
Hook an open chain link (GG) onto the loop (JJ). Close the chain links back
together with the pliers. The other end lock to the chain holder (EE) use the
quick link (HH) to secure tightly.You can now pass the wires through the chain
loop (JJ) and tighten it to the fixture (A) securely. Then weave the wires
through every third chain ink (GG). Continue to pass the wires and chain
through the screw collar (DD) and canopy (KK).
Strip 3/811 of insulation from the electrical wire ends. Using wire nuts (BB),
connect the RIBBED fixture wire Ato the WHITE supply wire from the outlet box;
connect the SMOOTH fixture wire to the BLACK supply wire.Connect the fixture
ground wire and supply ground wire using a wire nut or by fastening to the
ground screw on the mounting strap. Push all wire connections into the outlet
box.
Tuck the wires into the junction box and slip the canopy (KK} over the chain
holder. Thread the screw collar (DD} onto the chain holder to secure the
canopy (KK} tightly to the ceiling.
Thread the lamps (not included} into the fixture sockets. Use 60-watt MAX incandescent candelabra base, SBCFL or SBLED.
WARRANTY AND EXCLUSIVE REMEDY:
Progress products, when properly installed and under normal conditions of use,
are warranted to our customers only to be free from defects in material and
workmanship at
time of shipment. All warranty claims must be asserted within one year from
date of purchase of the subject items; thereafter, warranty claims will not be
honored. Customers• sole remedy for a warranty claim or otherwise shall be
limited to repair or replacement of the subject product if it is shown to have
been defective in material or workmanship at time of shipment. Progress1s sole
and maximum liability for a defective product shall never exceed the cost of
the subject product. EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED
(AND THE EXPRESS WARRANTY OF TITLE), WE DISCLAIM ALL OTHER
WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO
EVENT SHALL WE BE LIABLE TO
CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR
ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED 10 BE
CAUSED BY ONE OR MORE
OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR
PRODUCTS. Therefore, the customer’s sole and exclusive remedy against us for
breach of the warranty, breach of contract or negligence or strict liability
or otherwise shall be limited to repair or replacement of the subject product
at our option (excluding installation and removal charges which shall not be
our liability) or, ifwe choose, refund of the purchase price. In no case does
our warranty and exclusive remedy extend to anybody other than our customers.
Our customers are not authorized to extend warranties or remedies on our
behalf to anyone. Such unauthorized extensions of warranties or remedies by
the customer shall remain customer’s responsibility. Customer is responsible
for determining the suitability ofour products for customer1s use or resale,
or for incorporating them into objects or for applications which customer
designs, assembles, constructs or manufactures.
Instructions d’Assemblage et Installation
Mise en garde: Lire les instructions avec soin et couper le courant au disjoncteur central avant de commencer !’installation.
MISE EN GARDE: Lire les instructions avec soin et couper le courant au disjoncteur central avant de commencer !’installation.
MISE EN GARDE: Risque d’incendie. Min 90°C conducteurs d’alimentation. Consulter un electrician qualifie pour assurer le bon conducteur de circuit de derivation.
MISE EN GARDE – Le verre est toujours fragile; maniez le(s) composant(s) et/ou I’ (les) ampoule(s) avec prudence.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>