Aquafire AWA-20-50 Water Vapor 20 Inch Built-In Electric Fireplace Insert Instruction Manual

Aquafire AWA-20-50 Water Vapor 20 Inch Built-In Electric Fireplace Insert

INTRODUCTION

Planning Information / AWA AQUAFIRE SERIES
® water vapor fireplace modules are extremely easy to install, simple to operate, and easy to maintain. When designing your fireplace, feel free to send us your plans for review and comments

Important Considerations:

• Determine best configuration for your installation:

  • (1) Recessed (2) Proud (in front of wall) (3) Free-Standing

• Provide electrical power (120 V outlet) and 1/4’’ water line in cutout cavity if it is to be direct plumbed.

• For easy removal of fireplace and periodic maintenance, follow suggested clearances.

• We recommend you do not install the units prior to completion of all construction to avoid construction debris and dust entering the unit which can cause problems with operation, and potentially damage components voiding the warranty. (important)

• Determine materials and finishes you expect to use; There are no issues created by heat, so choice of materials is limitless.

• Avoid placement where there are air currents from doors, windows, and from the HVAC system.
  Water Hardness: Only use moderately hard tap water between 3.5 to 8.5 Grains Per Gallon (7 is ideal). It’s best to have water tested before prolonged use; excessively hard water will coat internal parts with calcium & mineral deposits and shorten life of equipment and possibly void the factory warranty.

• If water is too hard, use an inexpensive in-line water softener. Inexpensive hardness test kits are available on Amazon.

• Installing the water vapor insert:

• Cutout dimensions are critical because modules suspend from the flanges that span the opening.

• Too small and fireplace will not fit; too large and fireplace module may fall thru the opening.

• See ‘How To’ YouTube Videos: search for ‘Lumina Products Inc’ and then watch the AQUAFIRE ® ‘How To’ Videos.

• Do not install fireplace until construction is complete. Equipment must be protected from dust and debris getting inside.

• Consult Owners Manual shipped with unit for more information.

• Manual is also available online; our office can send you a link to the most recent version

1. Controls
2. Fill Connection
3. Air Intake Vents (top)
4. Alternate Air Intake Vents (side)
5. Flange Support (suspension) (flanges run full length of unit)

INSTALLATION

RECESSED HEARTH

TYPES OF FIREPLACES INSTALLATION GUIDELINES

GLASS-ENCLOSED HEARTH INSTALLATION GUIDELINES

ROOM DIVIDER EXAMPLE

Note: Overall dimensions of this example of a room divider fireplace is 78“ wide x 20“ deep. Hood extends 4” past fireplace base on both sides. In this case it is shown 9 feet tall. Configuration designed to minimize light that would otherwise be cast up to the ceiling in the room. The upper wall section is a large hollow hood painted inside with flat black paint. Optionally the top of the AQUAFIRE® unit can be covered with granite or other decorative material. If so, then this AWA 60-150-60“ fireplace insert will require 150 sq in of unobstructed air intake thru the toe kick as shown in the schematic at the right. If a grill or grate covers the air intake you must compensate for the solid mass of the grill in your calculations. Do not cover the control buttons with stone. Stone should be easy to removal and allow the unit to be removed for service if necessary

TYPICAL LONG MULTIPLE MODULE FIREPLACES
**CUTOUT DIMENSIONS REFERENCE Chart: ***

• 20’’ AWA-20-50: 12.25’’ x 20.2’’
• 40’’ AWA-40-100: 12.25’’ x 40.2’’
• 60’’ AWA-60-150: 12.25’’ x 60.2’’
• 80’’ AWA-80-200: 12.25’’ x 80.3’’
• 100’’ AWA-100-250: 12.25’’ x 1 00.3’’
• 120’’ AWA-120-300: 12.25’’ x 1 20.3’’
• 140’’ AWA-140-350: 12.25’’ x 1 40.3’’
• 160’’ AWA-160-400: 12.25’’ x 1 60.3’’
• 180’’ AWA-180-450: 12.25’’ x 1 80.3

AWA AQUAFIRE MODULES ARE DESIGNED TO BE FLUSH MOUNTED

• Air intake thru lid
• Air intake thru side panels (optional) (allows vents thru lid to be covered and requires air intake from below)
• Suspension flanges
• Fins control light spread

WATER HARDNESS + CHECKLIST FOR BEST RESULTS

Water Hardness Table of Classifications

• grains per
• milligrams per liter (mg/L)
• U.S. Geological Survey
• Water Quality Association
• gallon (gpg)
• parts per million (ppm)
• Classification

CHECKLIST FOR BEST RESULTS: REMEMBER

• protect fireplace insert during construction / dust & debris that gets inside the equipment is a major problem.
• have water tested for water hardness or use a water hardness kit purchased on line.
• water that is too hard will shorten life of equipment and could void warranty in extreme cases.
• water without enough minerals (too soft) will greatly limit size and quality of flames.
• flames look best against a dark background.
• drafts from HVAC vents and entrance doors will diminish quality of flames.
• if light cast onto the ceiling of the room is an issue, design a hearth, hood, or light trap to contain the light.
• mist-makers have a life of 2,000 to 3,000 hours and should be cleaned with vinegar 2 to 3 times a year.
• water tanks should be flushed with vinegar and rinsed out with water at least once a year.
• regular cleaning will prolong the life of the fireplace, see recommended Preventive Maintenance Plan

Design Review

When you have your design schematic or working drawings, it’s a good idea to get a review by a water vapor fireplace professional.

COMPARISON

FIREWATER PRESTIGE SERIES vs AQUAFIRE SERIES

Documents / Resources

| Aquafire AWA-20-50 Water Vapor 20 Inch Built-In Electric Fireplace Insert [pdf] Instruction Manual
AWA-20-50 Water Vapor 20 Inch Built-In Electric Fireplace Insert, AWA-20-50, Water Vapor 20 Inch Built-In Electric Fireplace Insert, Electric Fireplace Insert
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>