LUMEC RFG3 Roadway Optical Shields Instruction Manual

: June 9, 2024
: LUMEC

Table of Contents

RFG3 Roadway Optical Shields
RISK OF PRODUCT DAMAGE
Luminaire Maintenance
ROADWAY OPTICAL SHIELDS
SHIELD REMOVAL
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ROADWAY OPTICAL SHIELDS
LEDGINE IP66
INSTALLATION INSTRUCTIONS FOR ALL OPTIONS
0000000000

RFG3 Roadway Optical Shields

IMPORTANT: FOR YOUR PROTECTION, YOU MUST CAREFULLY READ ALL WARNINGS AND INSTRUCTIONS IN THEIR ENTIRETY PRIOR TO INSTALLATION, OPERATION, SERVICE OR MAINTENANCE. FAILURE TO DO SO CAN RESULT IN DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. If you do not understand these warnings and instructions, or if additional information is desired, please contact Signify, Lumec. TSC@signify.com phone 1-833-744-6439.

Installation, service and maintenance of luminaires must be performed by a qualified professional and in accordance with all federal, state and local laws, regulations and electrical codes. This professional should be familiar with the construction and operation of this product and any hazards involved. If not qualified, do not attempt installation, service or maintenance.
To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts, abrasions and other hazards, please read all warnings and instructions included with the luminaire, on the luminaire’s packaging and affixed to the luminaire itself.
Maintenance of the luminaires should be performed by person(s) familiar with the luminaire’s construction and operation and any hazards involved.

WARNING
RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY

Disconnect or turn off power before attempting any installation, service or maintenance.
Verify that supply voltage is correct by referencing the luminaire label information.
Make all electrical and ground connections in accordance with the National Electrical Code (NEC) and any other applicable laws, regulations or codes.
All wiring connections should be capped with UL-approved wire connectors.

WARNING
RISK OF FIRE OR PERSONAL INJURY

Keep combustible materials away from LED/lamp & lens
Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.

WARNING
RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY

Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
Avoid direct eye exposure to the light source while it is on.

WARNING
RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY

Allow Led/lamp & lens to cool before handling.
Do not touch enclosure or light source
Do not exceed maximum wattage marked on luminaire label.
Follow all manufacturer’s warnings, recommendations, instructions and restrictions for driver type, burning position, mounting locations and replacement.

CAUTION

RISK OF PRODUCT DAMAGE

Never connect luminaires and/or components under load with supply voltage turned on.
Do not mount or support these luminaires in a manner that can cut the outer jacket or damage wire insulation.
Do not restrict fixture ventilation. Allow for some volume of airspace around luminaire. Avoid covering luminaire with insulation, foam or other material that will prevent convection or conduction cooling.
Do not exceed luminaire maximum ambient temperature.
Do not modify the luminaire.
Only use luminaire in its intended application and location.
Led products are polarity sensitive. Ensure proper polarity before installation.
Electrostatic Discharge (ESD) can damage LED. Personal grounding equipment must be worn during all installation and servicing of the luminaire.
Do not touch individual electrical components as this can cause ESD, shorten LED life, or impact LED performance.
Some components inside the luminaire may not be serviceable. In the unlikely event your luminaire may require service, stop using it immediately and contact Signify.
Always read the luminaires complete installation instructions prior to installation for any additional luminaire specific warnings.
In the case of HID or Fluorescent luminaires, regular re-lamping is required to keep luminaire operating within safe limits
Do not install damaged product. Handling and installing damaged products can potentially increase the risks mentioned In case of damage and/or missing parts upon arrival of the luminaire.
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation or maintenance.
Please see luminaire specific Installation and Maintenance Instruction for additional warnings or any applicable FCC or regulatory statements. Failure to follow any of these Instructions could void luminaires warranties.

Luminaire Maintenance

Regular luminaire maintenance programs are recommended.
It is recommended to clean the outside of the luminaire and the refractor/lens.
Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user.
If clean water is not sufficient for cleaning, use a neutral, synthetic, not-scratching and not-abrasive cleaning substance.
Never use alkaline and/or acetous cleaning substances.
Make sure that the cleaning substance is carefully removed by rinsing with lots of clean water.
Signify recommends using a cleaning solution that has a PH between 5 and 8.
Recycle: For information on how to recycle electronic products and components, please visit www.epa.gov.

ROADWAY OPTICAL SHIELDS

NOTE:

This instruction sheet refers to roadway LEDgineIP66 fixtures.
There are 6 configurations compatible with LEDgineIP66, 10 LEDs & 7 configurations compatible with all LEDgineIP66, 40 LED products.
Although illustration shows installation for one configuration, they are all installed/removed in the same way as illustrated.
Instructions apply to all versions.

10LEDs Nano

| HOUSE SIDE SHIELD 10LEDS IP66 (HSS)
---|---
| CUL-DE-SAC SHIELD 10LEDs IP66 (CSS)
| FRONT SIDE SHIELD 10LEDs IP66 (FSS)
| LEFT SIDE SHIELD 10LEDs IP66 (LSS)
| RIGHT SIDE SHIELD 10LEDs IP66 (RSS)
| HOUSE SIDE SHIELD 10LEDS IP66 (HSS-4)

40LEDs Mini

| CUL-DE-SAC SHIELD 40LEDs IP66 (CSS)
---|---
| FRONT SIDE SHIELD 40LEDs IP66 (FSS)
| FRONT SIDE SHIELD 40LEDs IP66 (FSS-4)
| HOUSE SIDE SHIELD 40LEDS IP66 (HSS)
LUMEC RFG3 Roadway Optical Shields - Fig11 | HOUSE SIDE SHIELD 40LEDS IP66 (HSS-4)
| LEFT SIDE SHIELD 40LEDs IP66 (LSS)
| RIGHT SIDE SHIELD 40LEDs IP66 (RSS)

GENTLY PUSH THE SHIELDS TO SNAP INTO THE MODULES ON THE ALLOCATED FEATURES (ALL SNAPPING FEATURES NEED TO BE SECURELY SNAPPED).

LUMEC RFG3 Roadway Optical Shields - Fig12

SHIELD REMOVAL

USE A SMALL SCREWDRIVER TO REMOVE THE SHIELD FOR EACH SNAPPING FEATURE

RELEASE THE SNAPPING BY SLIGHTLY TURNING THE SCREWDRIVER

LUMEC RFG3 Roadway Optical Shields - Fig 14

©2020 Signify Holding. All rights reserved. This document may be subject to change. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed All trademarks are owned by Signify Holding or their respective owners.
www.lumec.com

Signify North America Corporation
200 Franklin Square Drive,
Somerset, NJ 08873
Telephone 855-486-2216| Signify Canada Ltée.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Tel. 800-668-9008
---|---