tuya WG103T Kit Video Alarm System GSM WiFi User Manual

tuya WG103T Kit Video Alarm System GSM WiFi

Overall state

Explanation

For all the issues stated in this manual:

• The icon is only valid for the corresponding alarm host which is configured with WiFi module.
• The icon is only valid for the user who has applied alarm service from local intra net alarm center.

Features

• 2.4 inch TFT display screen, concise user interface and menu hint design.
• Main interface status bar, dale/clock indication, fairly obvious alarm host status. Built-in powerful performance CPU master based on 32-bit Cortex-M3 core. Based on uCOS – 111 operating system with multitasking design, great user operation experience.
• WIFI/GSM/3G/GPRS intranet alarm system, support different alarm channels, like APP push/SMS/voice monitoring/intranet center etc. to ensure the alarm performance stable and reliable.
• Support SMS arm/disarm and voice arm/disarm
• Support up to 100 lea ring/storage location for remote control, RFID cards and wireless detector.
• Support many defense zones, such as gate, SOS, bedroom, window, balcony, perimeter, smoke, gas, carbon monoxide, water leaking, etc.
• Support the main power malfunction, backup power shortage, tamper alarm and other extended alarm.
• Support entry/exit zone, indoor zone, perimeter zone, 24-hour zone .. etc.
• Up to 5 groups preset alarm phone numbers, SMS on/off and dial on/off can be set respectively.
• Support external wireless siren.
• Support timing arm and disarm
• Can store and inquire daily operation records and alarm records.
• GSM network clock synchronization, to ensure accurate clock, and support country time zone setting.
• Support multi-language menu display, voice prompts and alarm SMS setting. Can record 20 seconds voice message and alarm voice.
• Telephone function, support 5 groups re-dial number.
• User-friendly APP operation experience and user interface.
• Push Arm/disarm message to APP
• Support APP remote arm/disarm
• Online GPRS to obtain equipment status, automatic alarm when offline. Reserved remote GPRS TCP / UDP protocol channel, compatible with multiple alarm center networking protocol to facilitate network alarm.
• Center remote control.

Identification for daily operation

• Arm
  set security task (i.e. Anti-burglar), make the host into alert state, also known as Arming, Alert or Booting. Designate security guard mission(i.e. Anti burglar), set the alarm host into on-guard status, also called Arming, Alert or Power on.

• Stay Arm
  In case the user is at home, only set alert to entrance/exit or perimeter, also called home alert.

• Disarm
  Withdraw security task(i.e. Anti-burglar), also called Withdraw alert or Power off. Trigger
  Under Arm state, detector detects someone or door is opened, it will trigger the detectors and make alarms.

• Exit delay
  After setting the host to be Arm state, in order to avoid making alarms for the users leaving and passing the Arm zones, delay the alarm time.

• Entrance delay
  When user comes back and pass the Arm zones, the host will not immediately make alarms. It will allow user to Disarm the host with some time; the host will make alarms if time out beyond the Disarm.

• Alarm
  When the host create alarm action, acousto -optical alarm signal arises. The host will send SMS message to the preset mobile phone, dial the preset user telephone number, create push to mobile phone APP, or send alarm information to intranet security center.

Alarm host appearance and accessories

Top view

Bottom view

Side view

Key of side face

Main interface

**Description for main interface

**

Menu structure

Note:

1. When the main keyboard is unlocked, if the user does not do any action or directly press 1§1 Key, then the keyboard is locked. After the keyboard is locked, the user needs to input password before using the keyboard.
2. When keyboard backlight is off, if the user does not do any action under main interface, or directly press 1§1 key, then the backlight is off to save power.
3. When certain language is selected, then the operation voice reminder, display and alarm SMS all are converted to this language. The alarm host will restart when language selection is confirmed

Initial usage

Start

• Insert SIM card: According to the below diagram, insert a MICRO SIM card. When a ticking voice is heard, it means the SIM card is inserted properly.
• Power on: Plug the power adaptor into the jack to turn on the power.
• “‘ Turn on the alarm host: Press Power On/Off key, a “welcome” window appears, then the alarm host is turned on.
• “‘ Turn off the alarm host: Press and hold Power On/Off key for 3 seconds until the screen is off, then the alarm host is turned off

System initialization

Continuously press Power On/Off key for 5 times, the alarm host will restart, then system initialization is finished. After system initialization, all the data including remote control, wireless detector, RFID card, language and time zone and other setting are reset to factory default all. IP address is cleared and the alarm host is offline GPRS. The IP address needs to be set again to assure the alarm host to go on line and connect with intra net center.

Please be cautious to use this function. Normally it is only used when user forgets password, or alarm host malfunction, or the parameter is wrongly set, or unknown detector, remote control or RFID card are learnt.

Menu operation

• Description for operation keys
• Press Previous [I]and Next key [I] to select menu.
• Press Return key 1§1 to last menu.
• Press Enter key 0 to next menu

1. When is used as backspace key, long press [I] to delete all input information.
2. For the other function which is not mentioned in this paragraph, please refer to the description in the “Menu Structure

Phone number setup

The host can set up to maximum 5 groups of alarm numbers, each set of numbers can be set independently of their dial-up switch and SMS switch. Take example as phone number 1:

• Operation Keyboard: Main Menu➔ Phone➔ 1st Phone, enter into phone number setup menu
• Press 0 to confirm, the alarm host will display “Setting OK”.

Add/Delete remote control

Add

• “‘ Operation Keyboard: Main Menu ➔ Parts➔ Add Remoter ➔ Enter.
• “‘ The alarm host displays “Synchronize” and enters into the 20- seconds countdown dialog window waiting for the remote control synchronization.
• “‘ Press any key of the remote control to send signal to the alarm host.
• “‘ The alarm host displays “Learning OK”, then the remote control is successfully added.
• “‘ If the alarm host displays “Device code has been learnt”, it means this remote control is already added to this alarm host, please use other remote control to try again.

Delete

• “‘ Operation Keyboard: Main Menu ➔ Parts ➔ Del Remoter ➔ Enter.
• “‘ The alarm host displays “Delete Remoter all”, meanwhile all stored remote control’s number is displayed in the dialog window.
• “‘ Press 0 to confirm, the alarm host displays “Operation OK”, all remote control is deleted.

Add/Delete wireless detector(included doorbell alarm)

Add

• “‘ Operation keyboard: Main Menu ➔ Parts ➔ Add Detector ➔ Enter
• “‘ It enters into “Set Name and Mode” dialog window Press 0 confirm The alarm host displays “Synchronize” and enters into the 20- seconds countdown dialog window waiting for the wireless detector synchronization.
• “‘ Trigger the wireless detector to launch wireless signal to the alarm host.
• The alarm host displays “Learning OK”, then the wireless detector is successfully added.
• If the alarm host displays “Device code has been learnt”, it means this wireless detector is already added to this alarm host , please use other wireless detector to try again.

Delete

• Operation keyboard: Main Menu ➔ Parts➔ Delete Detector➔ Enter
• The alarm host displays “Delete detector all”, meanwhile all stored detector’s number is displayed in the dialog window.
• Press [;Zito confirm, the alarm host displays “Operation OK”, all wireless detector and doorbell are deleted.

Add/Delete RFID card

Add

• Operation keyboard: Main Menu ➔ Parts➔ Add RFID ➔ Enter
• The alarm host displays “Synchronize” and enters into the 20- seconds countdown dialog window waiting for the RFID card synchronization. Put the RFID card close to
• the sensitive area on the down-right corner of the alarm host.
• The alarm host displays “Learning OK”, then the RFID card is successfully added.
• If the alarm host displays “Device code has been learnt”, it means this RFID card is already added to this alarm host.

Delete

• Operation keyboard: Main Menu➔ Parts➔ Del RFID ➔ Enter
• The alarm host displays “Delete RFID all”, meanwhile all stored RFID card’s number is displayed in the dialog window.
• Press 0 to confirm, the alarm host displays “Setting OK”, all RFID cards are deleted.

Synchronization with external wireless siren

• This operation instruction is subject to our company model PE-519 wireless siren.
• “‘ Operation keyboard: Main Menu ➔ Parts➔ Siren Learn➔ Enter
• Press and hold the Set button on the siren until 2 sound is heard. The siren’s indicator will flash quickly, then it enters into synchronization status.
• Press 0 to confirm, the alarm host displays “Learn Signal Sent” and send wireless signal to the siren.
• A long and a short sound arise from the siren, which means successful synchronization.
• After the wireless siren is synchronized with the alarm host, if the alarm host triggers alarm, alarm sound will arises from the siren at the same time.

Record

Record alarm voice

• The user can record 20-seconds voice. If alarm occurs, the alarm host will dial preset phone number and play this record alarm voice.
• Operation keyboard: Main Menu ➔ Record➔ Record and Play
• At first the alarm host will display “Busy and waiting please”, when it changes to “Recording”, it means start to record voice.
• After recording is finished, the alarm host displays “Playing”and starts automatic playback.
• After playback is finished, press 0 to save. The alarm host displays “Please wait saving”. After a few seconds, “Setting OK”appears, then recorded voice is saved.

Timer
The users can set automatic arm/disarm time according to their own routine time, avoiding repeated operation or missed arm/disarm.

Arm Timer

Operation keyboard: Main Menu ➔Timer➔ Arm Timer

Disarm Timer

Operation keyboard: Main Menu ➔ Timer ➔ Disarm Timer

Remote SMS

Parameter setup

• The user is required to edit SMS message according to below format, and send the
• SMS message to SIM card in the alarm host.

One SMS message can includes one or more address or content, but it must be separated by• and the first and last data must be•. The address should be founded of 2 digits. One SMS content can include maximum 160 bits. It is suggested to put all contents in one SMS.

Note: Below examples are based on default system password 6666

• lnitialization: All learnt remote control, wireless detector and RFID card are remained, the other parameter is reset to factory default. Set SMS contents:I666643*I

• Format of alarm phone number:xxxxxxxxxxx,A,B
  XXXXXX is phone number(Max. 18 digits), A is calling alarm switch(1-on, 0-off). Bis SMS alarm switch(1-on, 0-off) .
  Example: Set 2 alarm phone numbers as 13912345678 and 075581234567. 13912345678 is used to receive calling and SMS alarm, 075581234567 is used to receive calling alarm, then please set SMS contents according to below format:
  166665113912345678, 1, 1 *52075581234567, 1,0·1

• Format of IP address: : aaa,bbb,ccc,ddd,xxxxx aaa,bbb,ccc,ddd is IP address, xxxxx is the port, separated with comma.
  Example: Set GPRS server IP address as 116.62.42.223, port is 2001, then please set SMS contents according to below format:
  1666690116,62 ,42,223,2001

• Set GPRS APN
  Example : The local GPRS APN is internet.beeline.kz, then please set SMS contents according to below format:
  1666692 internet. bee Ii ne. kz*.

• Set Greenwich time zone : Set auto synchronization between alarm host clock and internet time. Time difference zone range: – 12.0-13.0

Alarm host name setup

The user can set a name for the alarm host which is used as the prefix of SMS phone number. This helps to recognize the alarm host or specific alarm location.
Example: SMSl1234@XX Building a Bloc@, 1234 is password,@ is command, XX Building a Block is the name(Max.40 bits)

Parameter inquiry

All feedback SMS contents are written in English, please inquire according to below description.

Inquire system setting

SMS format :1666662* I, Alarm host feedback SMS

Inquire system setting2

SMS format :1666690* I, Alarm host feedback SMS

Alarm phone setup inquiry

SMS format :1666651* I, Alarm host feedback SMS :

Delay setup inquiry

SMS format :1666633* I, Alarm host feedback SMS :

Switch setup inquiry

SMS format :1666646* I, Alarm host feedback SMS :

Remote control/detector/RF ID card inquiry SMS format :

1666626*1, Alarm host feedback SMS:

Phone function

In Main Interface, press 1 key to make calling. Please operate according to the hint in this interface.

In case of following condition, No GSM network, in Arm mode, on alarm, making a call is forbidden.

Daily operation

The user can control the alarm host by any of following ways:

• Remote control, Keyboard, RFID card.
• Remote SMS.
•  Mobile phone APP.
•  GPRS alarm center.

Out Arm

• By remote control: press key to activate Out Arm.
• By keyboard: In Main Interface, press . to activate Out Arm.
• By RFID card: In Disarm mode, put the RFID card close to the sensitive area on bottom right corner of the alarm host.
• By remote SMS: Send SMS message! 1234#11 ( 1234 is user password) at first, then the alarm host will feedback “System Armed!” SMS to mobile phone to confirm.
• By APP: Press Arm button, the alarm host will report “System Disarmed” . App status changes to Arm
• The alarm host reminder: A reminding voice “System armed” will be heard, the Main Interface displays “Armed” and “Please exit”, and an exit time progress bar appears.
• The user should leave the alarm zone before exit time. If Arm/Disarm SMS
  switch is on,the preset phone will receive “System Armed!” SMS.

Under Out Arm mode, all defense zones are on alert status. If any defense zone is triggered, the alarm host will generate a local siren alarm, and send alarm SMS or make calling lo the preset phone numbers, and simultaneously send the alarm message to the mobile phone APP or GPRS alarm center.

Stay Arm

• By remote control: Press key to activate Stay Arm.

• By keyboard: In Main Interface, press lock key for twice to activate Stay Arm.

• By APP: Press Stay Arm button, App status changes to Stay Arm

• The alarm host reminder: A reminder voice “System armed” will be heard, the Main Interface displays “Stay Armed”. If Arm/Disarm SMS switch is on.the preset phone
  will receive “System Stay Armed! ” SMS.

• Under Stay Arm mode, only valid Stay Arm defense zones are on alert status. If any defense zone is triggered, the alarm host will generate a local siren alarm, and send alarm SMS or make calling to the preset phone numbers, and simultaneously send the alarm message to mobile phone APP or GPRS alarm center.

Disarm

• By remote control: Press  ‘key to activate Disarm
• By keyboard: In Main Interface, press to activate Disarm
• By RFID card: In Arm/Stay arm mode, put the RFID card close to the sensitive area on bottom right corner of the alarm host.
• By remote SMS: Send SMS messagel1234#2l(1234 is user password) at first, then the alarm host will feedback “System Disarmed! “SMS to mobile phone to confirm.
• By APP: Press Disarm button, app status change to Disarm
• The alarm host reminder: A reminding voice “System Disarmed” will be heard, the Main Interface displays “Disarmed”. If Arm/Disarm SMS switch is on,the preset phone will receive “System Disarmed!” SMS.

Under Disarm mode, all the alarm procedure will be terminated.

SOS

• By remote control: Press sos key to activate SOS.
• By keyboard: In Main Interface, press to activate Disarm
• By APP: Press ” SOS” key to activate panic alarm.
• The alarm host reminde: The Main Interface displays “Help”. The alarm host will generate a local siren alarm, and send alarm SMS or make calling to the preset phone numbers simultaneously send the alarm message to mobile phone APP or GPRS alarm center.

SMS notification feedback

• : Remote operation result

Alarm and remote monitoring

The alarm host supports diverse alarm types. When alarm is triggered, it will send alarm SMS to the user’s mobile phone and push alarm message to APP, simultaneously send alarm message to GPRS alarm center and make calling to the user, then the user can do on-time monitoring and remote operation.
The alarm host also support following alarm types,

• The main power malfunction(when main power malfunction lasts for 5 seconds, the alarm is activated)
• Back up battery shortage(ln case of main power malfunction, when back up battery’s voltage is lower than 3.45V and lasts for 10 seconds, the alarm is activated)
• Main power recovers.
• Anti-tamper alarm(When the mounting bracket is separated with the alarm host, the alarm is activated).

SMS alarm

When any alarm is triggered, the alarm host will send SMS to preset phone numbers as following contents:

I <The alarm host! name>:

Voice alarm and remote monitoring

• Automatic dialing preset phone number when the alarm host alarms
• When any alarm is triggered, the alarm host will automatically dial preset phone numbers(make sure the dial switch is on). After the user ringed, the alarm host will play current alarm type at first If there is a preset voice, this voice will be played. Then the user will hear reminding voice “Press 1 to arm, press 2 to disarm, press 3 to monitor, press 4 to talk”. If it is mistake alarm, the user can press “2” to activate Disarm. The user also can press “3” or “4” to turn off the alarm sound for better monitoring. If monitoring is unnecessary, just quit calling.
• If the user does not answer the call or failed calling, the alarm host will constantly dial the preset phone number according to the preset redial times until the user answers the call.
• Preset phone number to call alarm host
• If the preset phone number voluntarily calls the alarm host, the alarm host will automatically answer the call, then the user can do on-time monitoring and remote operation.

Receiving alarm by Intranet monitoring center

When any alarm is triggered, the alarm host will send alarm message to GPRS alarm center. The alarm center can handle the alarm quickly after receiving and confirming the alarm message.

The function is only valid when the IP address is correctly set. Proper APN setting is required for foreign countries. Please refer to “SMS parameter setup” for details.

Specification

• Input voltage: DC5V(micro USB jack)
• Working current: <120mA
• Standby current: <80uA
• Siren output :<500mA
• Wireless frequency: 315MHz/433MHz/868MHz
• Wireless coding: EV 1527
• GSM bands: 850/900/1800/1900MHz
• WiFi standard: IEEE802.11 b/g/n wireless standard
• Back up battery: 3.7V/1000mAh lithium battery
• Working temperature: -10-55°(
• Relative humidity: < 80%RH (No freezing)
• Product dimension: 185x125x14. ?MM (LxHxT)

Packing List

• Alarm host x1
• Micro USB 5V/1 000mA Power adapter x1
• Wireless PIR detector x1
• Door sensor x1
• Remote control x2
• RFID card x2
• Wired siren x1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>