JBC AN115 Adjustable Nano Tweezers Instruction Manual

: June 9, 2024
: JBC

JBC AN115 Adjustable Nano Tweezers

JBC AN115 Adjustable Nano Tweezers

Packing List

The following items are included:

Adjustable Nano Tweezers ….. 1 unit

Manual … 1 unit
Ref. 0029831

Packing List

Connections

not included, sold separately

Changing Cartridges

Save time and change cartridges safely without having to switch the station off.

Removing

Changing Cartridges

Place the cartridge into the extractor slot (1) and pull the tweezers to remove the cartridge (2).

Inserting

Changing Cartridges

Push the tweezers onto the new cartridge until the reference ring*.

Aligning

Changing Cartridges

Use the holes to rotate the cartridges for a proper alignment.

Changing Cartridges

Vertical Cartridge Alignment

Changing Cartridges

Turn the tweezers hand whell forwards or backwards for a vertical cartridge alignment. One tip lines up with the other.

Important For a correct connection, it is important to push the cartridge in until the reference ring rests against the tweezers.

Example:

Chip Compoments Rework Process using Tweezers and Pedal

The Pedal is frequently used to rework components with tweezers.

AN115, JBCs Adjustable Nano Tweezers, is the most effective tool for disordering chip component but also it facilitates its rapid placement and soldering by using P405 pedal connected to JBC´s NAS station.

Connections

Connect pedal P405 to the same port where AN115 Nano tweezers are connected.
In the peripherals menu for the “Pedal Activation Mode” choose between “pressed” and “released”.

Chip Compoments Rework Process using Tweezers and
Pedal

Desoldering

Lift the tweezers from the holder, press and hold the pedal to activate the tweezers and desolder the component.
Once the pedal is released the tweezers enters in hibernation mode and cools down.

Chip Compoments Rework Process using Tweezers and
Pedal

Pad Cleaning

Clean the pads with JBC´s desolvdering tool DS360.
For this operation JBC´s desoldering station DSS is needed.

Solder Paste Dispensing

Apply the solder paste amount needed to solder the new chip component.
The use of JBC´s DPM solder paste dispenser is recommended.

Chip Compoments Rework Process using Tweezers and
Pedal

Placing

Do not press the pedal. Use the tweezers to position the component on the previously tinned pad.
Note: The inactive tweezers prevents the component from heating up prematurely.

Soldering

Once in position press and hold the pedal to activate the tweezers and perform the soldering.

Compatible Cartridges

The Nano Tweezers NP115 and AN115 work with C115 cartridges. Find the model that best suits your soldering needs on the Nano Tweezers NP115 and AN115 work with C115 cartridges. Find the model that best suits your
soldering needs on www.jbctools.com

Tweezer Conical Bent	****
Tweezer Chisel	****
Blade

Safety

Symbol It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.

Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.
The power cord must be plugged into approved bases. Be sure that it is properly grounded before use. When unplugging it, hold the plug, not the wire.
Do not work on electrically live parts.
The tool should be placed in the stand when not in use in order to activate the sleep mode. The soldering tip or nozzle, the metal part of the tool and the stand may still be hot even when the station is turned off. Handle with care, including when adjusting the stand position.
Do not leave the appliance unattended when it is on.
Do not cover the ventilation grills. Heat can cause inflammable products to ignite.
Avoid flux coming into contact with skin or eyes to prevent irritation.
Be careful with the fumes produced when soldering.
Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
Utmost care must be taken with liquid tin waste which can cause burns.
This appliance can be used by children over the age of eight and also persons with reduced physical, sensory or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning use of the appliance and understand the hazards involved. Children must not play with the appliance.
Maintenance must not be carried out by children unless supervised.

Specifications

AN115 Adjustable Nano Tweezers Ref. AN115-A

Cable length: 120 cm / 47.24 in
Total Net Weight: 50.6 g / 0.112 lb
Package Dimensions /Weight: 237 x 42 x 42 mm / 94.5 g (L x W x H) 9.33 x 1.65 x 1.65 in / 0.208 lb

Complies with CE standards. ESD safe.

Warranty

BC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.
Get 1 extra year JBC warranty by registering here: https://www.jbctools.com/productregistration/ within 30 days of purchase.

This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility

Symbols