RESIONE W90B Water-Washable Resin Instructions
- June 9, 2024
- RESIONE
Table of Contents
W90B Water-Washable Resin
Instructions
W90B Water-Washable Resin Instruction
The Product Description
W90B is a real water-washable resin, odorless, low irritation, available in 6
colors: clear, white, dark gray, black, clear orange, and clear blue. Prints
in translucent colors are more transparent after cleaning than regular resin
prints, while gray, black, and white prints have a silky, reflective surface.
The products have passed the inspection and obtained ROHS and REACH
certificates.
Material Properties Data
| METHOD| DATA
---|---|---
Viscosity（25℃）| ASTM:D4212-10| 139mpa.s
Shore Hardness| ASTM:D2240-05| 82D
Tensile Strength| ASTM: D638-14| 35.66MPa
Flexural Strength| ASTM: D790-10| 38.07MPa
Notched IZOD| ASTM:D256-10| 16.5J/m
Elongation at Break| ASTM: D638-14| 18%
Printing
Environment When Printing: Since W90B resin is a hydrophilic material,
this product is not recommended for printing in environments with humidity
higher than 60%. Supports Parameters: When the printing time is long, it is
best to use supports with the diameter of 0.8mm or more (Medium Supports) to
prevent the supports from absorbing water and softening.
Printing Settings: Use the standard resin settings of the printer brand
you successfully printed as the “Standard Settings” (25-30°C), otherwise, use
the default standard resin settings of the printer (or slicer) as the
“Standard Settings”. Then follow the following method to set the settings of
RESIONE resin according to the “Standard Settings”.
| Standard Settings| W9OBTransparent/White /Blue/gray/black| W9OBOrange
---|---|---|---
Layer Height(mm)| 50| 50| 50
Bottom Exposure Time(s)| A| 1 A| 1.2A
Exposure Time(s)| B| 0.7*B| 1.1`B
Light-off Delay (s)| D| D| D
Bottom Lift Distance(mm)| E| E| E
Lifting Distance(mm)| F| F| F
Bottom Lift Speed (mm/min)| G| G| G
Lifting Speed (mm/min)| H| H| H
Retract Speed (mm/min)| I| I| I
Note: a. When the room temperature during printing is lower than 24℃,
change the settings as follows every 5 below: Bottom exposure time: (RESIONE
settings) +15% Normal exposure time: (RESIONE settings) +15%
Light-off Delay time: (RESIONE settings) +1s
*The calculation of the above printing parameters is based on the experimental results of the RESIONE laboratory and is for reference only
Cleaning and Post-curing
Cleaning:
a. The prints should not be hung on the build plate for a long time, and need
to be shoveled off in time, cleaning and post-curing, otherwise the prints
will absorb water and become soft and deformed.
b. Put the print in a water container, shake it back and forth, and the
cleaning time should not exceed 3 minutes
c. The cleaned waste water should not be directly discharged into the sewer,
but should be placed in the sun to allow the waste liquid to dry and solidify
naturally. Post-curing: If you use a post-curing box with a power of 40W, our
recommended post-curing time is about 5mins
(Adjust the post-curing time according to the power of the post-curing box,
the greater the power, the shorter the time)
Attentions:
a. Too long post-curing time will make the resin prints easy to warping, hard
and brittle.
b. The resin prints will be fragile after post-curing. It is not recommended
to apply force to the prints immediately. Just need to wait for a while until
the internal stress of the prints is completely released.
Storage of Prints
a. Add the needed resin liquid when printing. To avoid moisture absorption of
resin,please filter the remaining resin as soon as possible and pour it into a
new light-proof container for sealing and preservation after printing.
c. The prints should not be placed in a humid environment for a long time,
otherwise they will absorb water and soften. Use an airtight bag or waterproof
paint to protect your prints effectively.
For more questions, please contact
support@godsaid3d.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>