Ender 3 V2 3D Printer Meanwell Power User Manual

Ender 3 V2 3D Printer Meanwell Power

Dear Consumers,
Thank you for choosing our products. For the best experience, please read the instructions before operating the Printer. Our teams will always be ready to render you the best services. Please contact us by phone number or e-mail address provided at the end when you encounter any problem with the Printer.
For a better experience in using our product, you can also learn how to use the Printer in the following ways:
View the accompanied instructions and videos on the storage card.
Visit our official website www.creality.com to find relevant software/hardware information, contact details, and operation, and maintenance instructions.

• Notes
• Product introduction
• Spare parts
• Assemble the 3D printer
• Use the 3D printer
• Start printing
• Wire connection
• Troubleshooting

NOTES

1. Do not use the printer any way other than described herein in order to avoid personal injury or property damage.

2. Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment.

3. Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.

4. Before using experimental or exotic filaments, we suggest using standard filaments such as ABS or PLA to calibrate and test the machine.

5. Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet.

6. Do not touch the nozzle or printing surface during operation as they may be hot. Keep hands away from machine while in use to avoid burns or personal injury

7. Do not wear gloves or loose clothing when operating the printer. Such cloths may become tangled in the printers moving parts leading to burns, possible bodily injury, or printer damage.

8. When cleaning debris from the printer hotend, always use the provided tools. Do not touch the nozzle directly when heated. This can cause personal injury.

9. Clean the printer frequently. Always turn the power off when cleaning, and wipe witha dry cloth to remove dust, adhered printing plastics or any other material off the frame, guide rails, or
   wheels. Use glass cleaner or isopropyl alcohol to clean the print surface before every print for consistent results.

10. Children under 10 years of age should not use the printer without supervision.

11. This machine is equipped with a security protection mechanism. Do not manually move the nozle and printing platform mechanism manually while booting up, otherwise the device will automatically power off for safety

12. Users shall abide by the laws and regulations of the country and region where the equipment is located (used), adhere to professional and ethical standards, and pay
    attention to their safety obligations. In all cases, the use of our products or equipment for any illegal purposes is strictly prohibited. The company is not liable for any legal
    responsibility arising from any violation.

13. Users shall abide by the laws and regulations of the country and region where the equipment is located (used), adhere to professional and ethical standards, and pay attention to their safety obligations. In all cases, the use of our products or equipment for any illegal purposes is strictly prohibited. The company is not liable for any legal responsibility arising from any violation.

Product introduction

1. XE-axis kit
2. X-axis limit switch
3. Print platform
4. Y-axis tensioner
5. Tool box
6. Nozzle it
7. Material rack and spool holder
8. Z-axis passive block
9. X-axis tensioner
10. Screen
11. Knob switch
12. Machine base
13. Power supply
14. Voltage regulator
15. Y-axis limit switch
16. Y-axis motor
17. Indication knob
18. E-axis motor
19. X-axis motor
20. Coupling
21. Z-axis limit switch
22. Z-axis motor
23. Power switch and socket

Equipment parameters

Spare parts

Accessory tool list

Installation of Z-axis limit switch kit and Z-axis profiles

Step: Put the end stops sensor on Z-axis (left) like in the picture above. Then use the four pieces screw M5X45 to fix Z-axis with the base.

Install Z-axis motor kit and t-type screw

Steps: Lock the T -shaped screw rod on the z-axis motor component, and then use two M4Xl8 screws to slightly lock the Z-axis motor component on the profile (as shown above)

Install pneumatic joint, XE-axis kit, and synchronous belt

Step: Tighten the tube connector by open end wrench. And fix the XE-axis kit with two pieces M4″16 screw. Put the timing belt through the XE-axis kit with direction same as the picture.

Install Nozzle kit, Z-axis passive block

Steps: Put the synchronous belt into the profile along the v-wheel of the nozzle kit. When pushing it into the middle, as shown in the figure; lock the z-axis passive block with one M4X16 screw.

Install X-axis Tensioner

Section diagram of synchronous belt moVing

Steps: Insert the timing belt into the tensioner block, and put it into the X-axis tensioner together with the timing belt, tighten it with a plastic hand screw nut, lock Z-axis passive block with one M4X16 screw, and then lock the M4X14 screw.

Install the z-axis moving kit and adjust the tightness of the X-axis and Y-axis tensioners

Tips: manually rotate the X-axis and Y-axis tensioners to be the appropriate tightness. Refer to A: the difference between the nut and the screw (protrusion) is 0-3mm. The reference standard is to press the synchronous belt with a little tension. A too loose or tight belt will affect the printing effect, and a too tight belt will to break. Refer to B: nut flush with a screw.

Steps: Make the Z-axis moving kit insert the two ends of the Z-axis profile along V-wheel on both sides. As shown in the figure above. The profile moves smoothly up and down along the Z-axis, and it will not fall off by itself.

Install the gantry profile,display kit

Steps: Install the profile or the gantry Trame on the upper of the gantry frame with 4 MSX25 hexagon socket head spring combination screws; firstly connect the display cable, then use the hex wrench to fix the 4 screws on the left side of the display module with the machine, locked the screws as well.

Install material rack, gantry cover, and indication knob

• Material rack x 1
• Material pipe and nut x1
• 2020 profile cover x2
• Hexagon socket flat round head screw M5X8 x2
• M5T nut x2
• Indication knob x1

Steps: Put flat round head M5X8 and MST screws into the material rack{as shown), place the spool holder on the rack and fix on the profile with screwslas shown); Put the indication knob on the motor shaft and then place the 2020 profile cover on both side.

Wire connection

• Connect X, E, Z-axis stepper motors according to the yellow label on the 6pin (4 wires) port
• Connect X, Z-axis limit switches according to the yellow label on the 3pin (2wires) port
• Plug in the power cord (as shown) and toggle the switch to turn on the power
• Insert the Teflon tube into the pneumatic connector (also insert the blue wire clamp)
• Caution
• Select the correct input voltage to match your local mains (115/230V)
• Damage can occur if the voltage is set incorrectly.
• Connect the power cord and turn the power switch to 1 to turn it on.
• Do not connect or disconnect the cables when the machine is powered on.

Bed Leveling

• Twist the coupling to raise the X-axis to the position as the picture shows. During the leveling process, please do not touch the Teflon tube and nozzle cable.
• Note : The Ul information is only for reference, the actual UI may be different.

1. Move the nozzle near the top of the leveling nut. Screw the nut and adjust the distance between the nozzle and the printing platform. The distance is about 0.lmm.
   (Thickness of a piece of A4 paper)

2. We can use a piece of A4 paper to assist in leveling, so that the nozzle can just scratch the A4 paper. Adjust the leveling nuts on the four sides in turn until you can feel
   the slight resistance from the nozzle when pulling the A4 paper.

3. Test the distance between the nozzle and the print platform is enough or not. Repeat the above steps 1-2 times if necessary.

Preheat

Method 1

Note: The Ul information is only for reference, the actual Ul may be different.

Method 2

Note: The print preheating standard is adjusted at the factory, PLA preheating standard: nozzle temperature 200°, hot bed temperature 60, ABS preheating standard: nozzle temperature 240°, hot bed temperature 70°. If you need to adjust it due to printing materials or other reasons, you can adjust the parameters on the interface home page control temperaturePLA/ ABS preheat setting
Note: The Ul information is only for reference, the actual Ul may be different.

Load the filament

1. When waiting for the temperature to rise, please hang the filaments on the material rack.
2. Press the extrusion spring and insert the filament until the nozzle along the extrusion. When the temperature is up to the target temperature, the filament will come out of the nozzle, nozzle, and complete loading the filament.

For better printing, the end of filament is as shown in the figure.

Replace the filament:

1. If no filament in the nozzle, cut the filament at the extruder, put the new filament into the tube, and until the filament arrives on the feeding tube.
2. If filament in the nozzle, heat up the nozzle to 185+, draw out the filament, and then replace the filament according to step 1.
3. If replace the filament during the printing process, adjust the printing speed to 10%, and then replace the filament according to step 2

Start printing

1. Double-click to install the software
2. Double-click to open the software.
3. Select language -Next -Select your machine>Next-Finish.
4. 0pen Creality 3D slicer Load (Read file) -> Select file.

Start printing

When printing for the first time, please level the platform first, otherwise, it will easily cause nozzle damage, plug and scratch the printing platform.

1. Insert the storage card press the knob selects the menu for the file to be printed.
2. Generate G-code, and save the code file to a storage card.

• File names must be Latin letters or numbers, not Chinese characters or other special symbols.
  Notes : For details on the software instructions, please refer to the slicing software manual on the storage card!

Start printing

Print

Note: The Ul intormation is only for reference, the actual UI may be different.

Wiring connection

Trouble shooting

• Due to the differences between different machine models, the physical objects and the final images can differ. The final explanation rights shall be reserved by Shenzhen Creality 3D Technology Co., Ltd.

• SHENZHEN CREALITY 3D TECHNOLOGY CO., LTD.
  

• Add:18F, Jin XiuHongDu Building, Meilong Blvd., Longhua Dist.,
  

• Shenzhen, China 518131
  

• Official Website:www.creality.com
  

• Tel: +86 755-8523 4565

• E-mail:info@creality.com cs@creality.com

References

• Creality - Global Leader in Consumer-Level 3D Printer Ecosystems and Creator

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>