UNIWATT UGB0502W Electric Baseboard Owner’s Manual
- June 9, 2024
- UNIWATT
Table of Contents
UNIWATT UGB0502W Electric Baseboard
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
-
Read all instructions before using this heater.
-
A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
-
This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains away from heater.
-
To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where open-ings may become blocked.
-
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
-
This product must be installed by a qualified person and connected by a certified electrician, according to the electrical and building codes effective in your region and NEC.
The following instructions must be adhered to avoid personal injuries or property damages, serious injuries and potentially fatal electric shocks. -
Protect the heating unit with the appropriate circuit breaker or fuse, in accordance with the nameplate.
-
Make sure the line voltage (volt) is consistent with that indicated on the unit’s nameplate.
-
This unit must be grounded.
-
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
-
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).
-
Do not install the unit where objects or furniture could be damaged by the heat.
-
Respect distances and positions indicated in the installation section.
-
If the installer or user modifies the unit, they will be held responsi-ble for any damage resulting from this modification, and the CSA/UL certification could be void.
-
When starting up the unit for the first time or after a long period, it is normal that it produces some temporary odours and whitish smoke.
-
Do not install on a wall behind a door.
-
Make sure the electrical connections are sturdy and have been executed correctly. Failure to comply with this directive could result in a fire.
SAVE THESE INSTRUCTIONS
MATERIAL REQUIRED: Flat and Phillips screwdrivers, screws, twist-on wire connectors, wire strippers, cable clamp connector.
INSTALLATION
CAUTION
- Do not install heater in any position other than as shown in this manual.
- Wiring procedures and connections should be in accordance with the National Electrical Code (NEC) and local codes.
- To reduce the risk of fire, do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater.
- Do not to install heaters against combustible low-density cellulose fiberboard surfaces.
- Do not to install heaters below an electrical convenience receptacle.
- Use only with copper branch circuit conductors.
- CAUTION – High temperature, keep electrical cords, drapes, and other furnishings away from heater.
- Keep drapes at a distance of at least 6 in. (15 cm) from unit.
- Do not install unit in contact with combustible materials
- Do not remove or bypass the thermal protection [G].
To ensure safe operation of the heating unit, the clearance specifications shown in the drawing below must be met.
PREPARING THE BASEBOARD
WARNING : Turn off the power supply.
- Remove the junction box cover [A].
- Remove one of the knockouts in the wiring compartment [B].
- Install a cable clamp connector (not included). Pull power cable supply through the cable clamp connector leaving at least 6 in. (15 cm) of wire leads.
CONNECTING THE WIRING
- Connect the grounding wire firmly with the green screw [E] provided.
- Connect the baseboard and power supply wires [C] ac-cording to the connection diagram. Tighten wires into the twist-on connectors [D] to make sure the connections are secure before pushing them back into the junction box.
- Screw the junction box cover [A] back on.
NET VOLUMES (cm³)
JUNCTION BOX| WITHOUT THERMOSTAT| WITH THERMOSTAT
Left| 691.04| N/A
Right| 681.05| 628.94
ATTACHING THE BASEBOARD TO THE WALL
- Attach the baseboard to the wall using at least four (4) mounting holes [F]. If no studs are available, anchors may be required. Do not over tighten.
OPERATION AND MAINTENANCE
WARNING : The baseboard must be properly installed before it is used. Fins are sharp and may cause cuts, do not touch.
- Once a year, or as required, use a damp cloth and non-abra-sive dish soap to remove any dust build-up. All other servic-ing is to be done by qualified service personnel.
- Before cleaning, make sure the power has been turned off at the circuit breaker panel, and wait until the elements have cooled before cleaning the unit or removing the front cover.
- If the unit is installed in a dusty area, use a vacuum cleaner to remove the dust.
- Replace front cover [H] if it was removed.
- Restore the power at the circuit breaker.
STELPRO LIMITED WARRANTY
This limited warranty is offered by Stelpro Design Inc. (“Stelpro”) and applies to the following product made by Stelpro: model UGB. Please read this limited warranty carefully. Subject to the terms of this warranty, Stelpro warrants its products and their components against defects in workmanship and/or materials for the following periods from the date of purchase: 2 years and 10 years warranty on the heating element (for first end user). This warranty applies only to the original purchaser; it is non-transfer-able and cannot be extended.
CLAIM PROCEDURE
If at any time during the warranty period the unit becomes defective, you must
cut off the power supply at the main electrical panel and contact 1) your
installer or distributor, 2) your service center or 3) Stelpro’s customer
service department. In all cases, you must have a copy of the invoice and
provide the information written on the product nameplate. Stelpro reserves the
right to examine or to ask one of its representatives to examine the product
itself or any part of it before honoring the warranty. Stelpro re-serves the
right to replace the entire unit, refund itspurchase price or repair a
defective part. Please note that repairs made within the warranty period must
be authorized in advance in writing by Stelpro and carried out by persons
authorized by Stelpro.
Before returning a product to Stelpro, you must have a Stelpro authorization
number (RMA). To obtain it, call the customer service department at:
1-844-STELPRO. The authorization number must be clearly written on the parcel
or it will be refused.
CONDITIONS, EXCLUSIONS AND DISCLAIMER OF LIABILITY
This warranty is exclusive and in lieu of all other representations and
warranties (except of title), expressed or implied, and Stelpro expressly
disclaims and excludes any implied warranty of merchantability or implied
warranty of fitness for a particular purpose.
Stelpro’s liability with respect to products is limited as provided above.
Stelpro shall not be subject to any other obligations or liabilities
whatsoever, whether based on contract, tort or other theories of law, with
respect to goods or services furnished by it, or any undertakings, acts or
omissions relating thereto. Without limiting the generality of the foregoing,
Stelpro expressly disclaims any liability for property or personal injury dam-
ages, penalties, special or punitive damages, damages for lost profits, loss
of use of equipment, cost of capital, cost of substitute products, facilities
or services, shutdowns, slowdowns, or for other types of economic loss or for
claims of a dealer’s customers or any third party for such damages. Stelpro
specifically disclaims all consequential, incidental and contingent damages
whatsoever.
This warranty does not cover any damages or failures resulting from: 1) a
faulty in-stallation or improper storage; 2) an abusive or abnormal use, lack
of maintenance, improper maintenance (other than that prescribed by Stelpro)
or a use other than that for which the unit was designed; 3) a natural
disaster or an event out of Stelpro’s control, including, but not limited to,
hurricanes, tornadoes, earthquakes, terrorist attacks, wars, overvoltage,
flooding, water damages, etc. This warranty does not cover any accidental or
intentional losses or damages, nor does it cover damages caused by negligence
of the user or owner of the product. Moreover, it does not cover the cost of
disconnection, transport, and installation.
The warranty is limited to the repair or the replacement of the unit or the
refund of its purchase price, at the discretion of Stelpro. Any parts replaced
or repaired within the warranty period with the written authorization of
Stelpro will be warranted for the remainder of the original warranty period.
This warranty will be considered null and void and Stelpro will have the right
to refuse any claims if products have been altered without the written
authorization of Stelpro and if the nameplate numbers have been removed or
modified. This warranty does not cover scratches, dents, corrosion or dis-
coloration caused by excessive heat, chemical cleaning products and abrasive
agents. It does not cover any damage that occurred during the shipping.
Some states and provinces do not allow the exclusion or limitation of
incidental or con-sequential damages and some of them do not allow limitations
on how long an implied warranty lasts, so these exclusions or limitations may
not apply to you. This warranty gives you specific legal rights and you may
have other rights which vary from state to state or from province to province
Saint-Bruno-de-Montarville, Quebec, Canada, J3V 6L7
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>