HAMPTON BAY 65875 2 in 1 Wall Sconce User Guide

HAMPTON BAY 65875 2 in 1 Wall Sconce

Safety Information

IMPORTANT SAFETY INSTRUCTIONS

Review these basic electrical guidelines before you begin this installation.

• Use tools with insulated handles and ladders made of wood or fiberglass.

• Keep dry-chemical fire extinguishers in the kitchen, basement, and workshop.

• Never disable grounding devices. Ensure all appliances that require grounding are properly grounded.
  Meet or exceed all electrical code requirements that cover the work you are doing.

• Always work with enough light to see what you are doing. It is easy to make a mistake when you work in dim light.

• When in doubt about the safety of any electrical repair or test, call in a professional.

WARNING: Before touching any wire, use a voltage tester to ensure it is not live.
WARNING: When you check for voltage in a receptacle, check both outlets as each may be controlled by a separate wiring circuit.
WARNING : Before working on a circuit, go to the main service panel and remove the fuse or trip the breaker that controls the circuit.
WARNING: When replacing fuses, turn off the main power first. Make sure your hands and feet are dry, and place one hand behind your back to prevent electricity from making a complete circuit through your chest. Touch a plug fuse only by its insulated rim. Remove cartridge fuses with a fuse impeller
WARNING: Consult a qualified electrician to ensure correct branch circuit conductor.
CAUTION: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Warranty

3-YEAR LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of three (3) years from the date of purchase. If within this period the product is found to be defective in material or workmanship, the product must be returned, witha copy of the bill of sale as proof of purchase, to the original place of purchase. The manufacturer will, at its option, repair, replace, or refund the purchase price to the original purchaser or consumer. This warranty does not cover light bulbs or the fixture becoming damaged due to misuse, accidental damage, improper handling and/or installation, and specially excludes liability for direct, incidental, or consequential damages. As some provinces do not allow exclusions or limitations on an implied warranty, so the above exclusions and limitations may not apply. This warranty gives you specific rights and you may also have other rights that vary from province to province.
Contact the Customer Service Team at 1-855-HD-HAMPTON or visit www.HAMPTONBAY.com.

Pre-Installation

PLANNING INSTALLATION
Compare all parts with the Hardware Included and Package Contents sections. If any part appears missing or damaged, do not install this
product and contact the Customer Service team at 1-855-HD-HAMPTON.

TOOLS REQUIRED

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

PACKAGE CONTENTS

Part      Description Quantity

A       I Fixture 1
B| Tube|
C| Socket ring (preassembled to Fixture assembly (A))|
D| Shade|
E| Bulb ( not included )|

Hardwire Installation

Removing the cord

• Carefully unpack and lay all parts on a clean, level surface.
• Remove the preassembled back plate (CC) by unscrewing the back plate screws (DD).
• Remove electrical tape on the wire connectors (GG) then turn the wire connectors (GG) counterclockwise and romove them from the black and white cord.
• Unwire the black and white wire from cord (making sure to keep rotary switch back wire connected/ intact). Slide cord out through hole and remove.

Installing the mounting plate

Attach the mounting bracket (FF) to the outlet box (not included) with outlet box screws (HH).

Making the electrical connections

• Make the connections to a 120V AC 60Hz circuit.
• Connect the negative wire (white) from the fixture to the negative wire from the outlet box, the positive wires (black) from the fixture to the positive wires from the outlet bOx, and connect the bare copper from the fixture around the green screw on the mounting bracket, then connect it to the grounding conductor of the supply circuit together. Secure all connections together with the wire connectors (GG) and wrap the electrical tape (not included) around the wire connec- tors (GG). Push all excess wire and wire connections back into the outlet box.
• Assemble tube (B) to fixture (A).

Attaching the canopy

Place the fixture (A) over the mounting bracket (FF) and align the holes of mounting bracket (FF) with holes on the fixture (A) and secure with mounting bracket screws (DD). Remove the socket ring (C) from the fixture (A)

Installing the shade and light bulb

Secure the shade (D) to the socket on the fixture (A) using the socket ring (C).
Install light bulb (E) (Not included) in the socket on the fixture (A). Use 60-watt max. E12-base Type-B or Type-Ca incandescent bulbs, or 10-watt max. E12-base LED bulb.

Plug-In Installation

Preparing for installation

• Carefully unpack and lay all parts on a clean, level Surface.
• Determine the desired location of the fixture making sure you have access to an electrical outlet and there are no electrical lines or plumbing where you intend to attach the mounting hardware.
• Mark the anchor (AA) locations on wall and drill each hole 7 mm in diameter.
• Insert the anchors (AA) and tap into the wall until secure.
• Set two mounting wall screws (BB) into the anchors (AA) using a screwdriver, leaving enough exposed to set into the keyhole slots on the fixture (A).

Attaching the canopy and the shade

• Assemble tube (B) to fixture (A). Remove the socket ring (C) from the fixture assembly (A).
• Secure the shade (D) to the socket on the fixture (A) using the socket ring (C).
• Align the keyhole slots on the fixture (A) with the mounting wall screws (BB) on wall and then gently push the canopy toward the wall and slide down until secure.

Adjusting the cord (optional)

The cord length between the plug (EE) and the canopy should be at least 5 ft (152.4 cm). Slide the plug cap off of the cord plug as shown in image below (The insulation of the ribbed side (neutral) wire shall be pierced by the wider blade pin of plug). Cut the cord to desired length. Re-attach cord to cord plug by inserting the cord back into the cord plug and pressing down firmly. Secure the cord by sliding the plug cap back onto the cord plug.

Installing the light bulb

Install light bulb (E) (Not included) in the socket on the fixture assembly (A). Use 60-watt max. E12-base Type-B or Type-Ca incandescent bulbs, or 10-watt max. E12-base LED bulb.

Care and Cleaning

WARNING: Before cleaning the fixture, disconnect the electrical power to the fixture by turning off the circuit breaker or removing the fuse at the fuse box.

• Use a dry or damp, clean cloth to wipe the surface of the fixture. Do not use abrasive cleaners or chemical solvents.
• Allow the fixture to dry completely before power is restored.

Troubleshooting

This portable luminaire has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use an extension cord unless plug can be fully inserted. Do not alter the plug.

Questions, problems, missing parts? Before returning to the store, call Hampton Bay Collection Customer Service
8 a.m. 7 p.m., EST, Monday Friday, 9 a.m.- 6 p.m., EST, Saturday
1-855-HD-HAMPTON
HAMPTONBAY.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>