AiM EVO4S Car Racing Datalogger User Guide
- June 9, 2024
- AIM
Table of Contents
AiM EVO4S Car Racing Datalogger
Models and years
This manual explains how to connect EVO4S and SOLO 2 DL to the bike engine
control unit (ECU) and how to install AiM SOLO 2/SOLO 2 DL on the bike
steering plate.
Compatible models are:
- Honda CBR 1000 RR 2004-2016
- Honda CBR 1000 RR HRC 2014-2016
- Honda CBR 600 RR 2003-2019
- Honda CBR 600 RR HRC with D11 marked ECU 2013-2015
Kit content and part numbers
AiM developed a specific installation bracket for SOLO 2/SOLO 2 DL and a connection cable to the ECU for EVO4S/SOLO 2 DL.
Bracket for SOLO 2/SOLO 2DL
Part number for SOLO 2/SOLO 2 DL installation bracket for Honda CBR 600 RR –
shown below – is: X46KSHCBR6.
Installation kit contains:
- 1 bracket (1)
- 2 allen screws with flat head M4x10mm (2)
- 1 washer (3)
- 1 allen screw with rounded head M6x60 (4)
- 1 rubber dowel (5)
AiM cable for EVO4S/SOLO 2 DL
Part number for EVO4S/SOLO 2 DL connection cable for Honda CBR 600 RR and CBR
1000 RR – shown below – is: V02569290. Following image shows the cable
constructive scheme.
Installation
bracket and connection cable for SOLO 2 DL for Honda CBR 600 RR can be bought
together. Part number: V0256929CS.
EVO4S/SOLO 2 DL connection
Honda CBR – RR bikes with PGM-Fi from 2003-2004 onwards communicate with Honda
diagnostic system (HDS) using K-line. To connect EVO4S/SOLO 2 DL to the bike
K-line, use the red Sumitomo connector (DLC) placed under the bike seat and
shown in the following pictures: it must be connected to the Sumitomo
connector of the AiM connection cable for EVO4S and SOLO 2 DL. 
Configuration with Race Studio 3
Before connecting EVO4S/SOLO 2 DL to the bike ECU, set all functions using the AiM software Race Studio 3. The parameters to set in the AiM device configuration section are (“ECU Stream” tab):
- ECU Manufacturer: “Honda”
- ECU Model must be set according to the following tab:
| Bike Model | “HDS_TAB10” | “HDS_TAB11” |
|---|---|---|
| Honda CBR 1000RR 2008 – 2016 | X | |
| Honda CBR 1000RR HRC 2014 – 2016 | X | |
| Honda CBR 600RR from 2008 | X | |
| Honda CBR 600RR HRC from 2013 with D11 marked ECU | X | |
| Honda CBR 1000RR from 2004 to 2007 | X | |
| Honda CBR 600RR from 2003 to 2007 | X |
Honda protocols
Available channels change according to selected protocol.
“Honda – HDS_TAB10” protocol
Received channels by EVO4S/SOLO 2 DL configured with “Honda – HDS_TAB10”
protocol are:
CHANNEL NAME
- HDS RPM
- HDS TPS V
- HDS TPS
- HDS ECT
- HDS IAT
- HDS MAP
- HDS BATT
- HDS SPD
- HDS IGN ANG
- HDS INJ Tms
FUNCTION
- RPM
- Throttle position sensor voltage
- Throttle position sensor
- Water temperature
- Intake air temperature
- Manifold air pressure
- Battery voltage
- Vehicle speed
- Ignition angle advance
- Injection time (milliseconds)
Technical note: not all data channels outlined in the ECU template are validated for each manufacturer model or variant; some of the outlined channels are model and year specific, and therefore may not be applicable.
“Honda – HDS_TAB11” protocol
Received channels by EVO4S/SOLO 2 DL configured with “Honda – HDS_TAB11”
protocol are:
CHANNEL NAME
- HDS RPM
- HDS TPS V
- HDS TPS
- HDS ECT
- HDS IAT
- HDS MAP
- HDS BATT
- HDS SPD
- HDS IGN ANG
- HDS INJ Tms
- HDS unk
FUNCTION
- RPM
- Throttle position sensor voltage
- Throttle position sensor
- Water temperature
- Intake air temperature
- Manifold air pressure
- Battery voltage
- Vehicle speed
- Ignition angle advance
- Injection time (milliseconds)
- Free channel to be assigned
Technical note: not all data channels outlined in the ECU template are validated for each manufacturer model or variant; some of the outlined channels are model and year specific, and therefore may not be applicable.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>