technicolor XB7 Wi-Fi Router Wall Mount Instructions

XB7 Wi-Fi Router Wall Mount
Instructions

SAFETY INSTRUCTIONS AND REGULATORY NOTICES

BEFORE YOU START INSTALLATION OR USE OF THIS PRODUCT, CAREFULLY READ ALL SAFETY INSTRUCTIONS

Applicability
These Safety Instructions and Regulatory Notices apply to:

• Technicolor Cable Modems & Gateways

Using equipment safely
When using this product, always follow the basic safety precautions to reduce the risk of fire, electric shock and injury to persons, including the following:

• Always install the product as described in the documentation that is included with your product.
• Do not use this product to report a gas leak in the vicinity of the leak.
• Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

Used symbols
Following symbols may be found in this and accompanying documentation as well as on the product or accompanying accessories:

this product may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make  any kind of contact with any inside part of this product.
| This symbol is intended to alert you of the presence of important operating and maintenance (servicing) instructions in the documentation that is included with your product.
| This symbol indicates for indoor use only (IEC 60417-5957).
| This symbol indicates Double insulated Class II equipment (IEC 60417-5172).
Does not require an earth connection.
| This symbol indicates Alternating Current (AC).
****| This symbol indicates Direct Current (DC).
| This symbol indicates Electrical polarity.
| This symbol indicates Fuse.

Directives

Product use
You must install and use this product in strict accordance with the manufacturer’s instructions as described in the user documentation that is included with your product.
Before you start installation or use of this product, carefully read the contents of this document for device specific constraints or rules that may apply in the country where you want to use this product.
If you have any doubts about the installation, operation or safety of this product, please contact your supplier.
Any change or modification made to this product that is not expressly approved by Technicolor will result in the loss of product warranty and may void the user’s authority to operate this equipment. Technicolor disclaims all responsibility in the event of use that does not comply with the present instructions.

Software and firmware use
The firmware in this equipment is protected by copyright law. You may only use the firmware in the equipment in which it is provided. Any reproduction or distribution of  this firmware, or any portion of it, without express written consent from Technicolor is prohibited.
Software described in this document is protected by copyright law and furnished to you under a license agreement. You may only use or copy this software in accordance with the terms of your license agreement.

Open Source Software notification

The software of this product may contain certain open source software modules which are subject to Open Source Software license terms (see https://opensource.org/osd  for definition). Such Open Source Software components and/or versions may change in the future versions of the software product.
A list of the Open Source Software used or provided as embedded into the current software of the product and their corresponding licenses and version number are, to the  extent required by applicable terms, available on Technicolor’s website at the following address: www.technicolor.com/opensource or at another address as Technicolor may provide from time to time.
If and where applicable, depending on the terms of the applicable Open Source Software licenses, the source code of the Open Source Software is available for free upon request.
For avoidance of doubt, Open Source Software is only licensed by the original owner of the Open Source Software under the terms set forth in the designated Open Source License.

Environmental information

Batteries (if applicable)
**** Batteries contain hazardous substances which pollute the environment. Do not dispose of them with other articles. Take care to dispose them at special collecting points.
Recycle or dispose of batteries in accordance with the battery manufacturer’s instructions and local/ national disposal and recycling regulations.

Energy efficiency
Energy savings
The user documentation that is included with your product not only provides useful information on all the features of your product, but also on its energy consumption. We  strongly encourage you to carefully read this documentation before putting your equipment in service in order to get the best service it can offer you.

Safety instructions

• Read these instructions.
• Keep these instructions.
• Heed all warnings and cautions.
• Follow all instructions.

Climatic conditions
This product:

• Is intended for in-house stationary use; the maximum ambient temperature must not exceed 40 °C (104 °F); the relative humidity must be between 20 and 80 %.
• Must not be mounted in a location exposed to direct or excessive solar and/or heat radiation.
• Must not be exposed to heat trap conditions and must not be subjected to water or condensation.
• Must be installed in a Pollution Degree 2 environment (an environment where there is no pollution or only dry, non-conductive pollution).
  If applicable, batteries (battery pack or batteries installed) must not be exposed to excessive heat such as sunshine, fire or the like.
  This product is intended for indoor use only.

Ventilation and positioning
This product is intended to be used indoors in a residential or office environment.

• Remove all packaging material before applying power to the product.
• Place and use the product only in positions as described in the user documentation that is included with your product.
• Never push objects through the openings in this product.
• Do not block or cover any ventilation openings; never stand it on soft furnishings or carpets.
• Leave 7 to 10 cm (3 to 4 inches) around the product to ensure that proper ventilation gets to it.
• Do not install the product near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Do not put anything on it which might spill or  drip into it (for example, lighted candles or containers of liquids). Do not expose it to dripping or splashing, rain or moisture. If a liquid enters inside the product, or if the product has been exposed to rain or moisture, unplug it immediately and contact your supplier or customer service.

Cleaning

Unplug this product from the wall socket and disconnect from all other devices before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Water and moisture
Do not use this product near water, for example near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool.
Transition of the product from a cold environment to a warm one may cause condensation on some of its internal parts. Allow it to dry by itself before using the product.

Electrical powering
The powering of the product must adhere to the power specifications indicated on the marking labels.
In case this product is powered by a power supply unit:

• For USA and Canada: This product is intended to be supplied by a UL listed Direct Plug-in Power Unit marked “Class 2” and rated as indicated on the label on your product.
• This power supply unit must be Class II and a Limited Power Source in accordance with the requirements of IEC 60950-1/EN 60950-1, Clause 2.5 or IEC 62368-1/EN  62368-1, Annex Q and rated as indicated on the label on your product. It must be tested and approved to national, or local standards.

Only use the power supply unit that is supplied with this product, is supplied by your service provider or local product supplier, or a replacement power supply unit provided  by your service provider or local product supplier.
The use of other types of power supplies is prohibited.
If you are not sure of the type of power supply needed, consult the user documentation that is included with your product or contact your service provider or local product supplier.

Accessibility

The plug on the power supply cord or power supply unit serves as disconnect device. Be sure that the mains supply socket outlet you use is easily accessible and located as  close to the product as possible.
The power connections to the product and the mains supply socket outlet socket must be accessible at all times, so that you always can disconnect the product quickly and  safely from the mains supply.
Overloading
Do not overload mains supply socket outlets and extension power cords as this increases the risk of fire or electric shock.
Handling batteries This product may contain disposable batteries.

CAUTION
There is danger of explosion if the battery is mishandled or incorrectly replaced.

• Do not disassemble, crush, puncture, short the external contacts, dispose of in fire, or expose to fire, water or other liquids.
• Insert batteries correctly. There may be a risk of explosion if the batteries are incorrectly inserted.
• Do not attempt to recharge disposable or nonreusable batteries.
• Please follow instructions provided for charging rechargeable batteries.
• Replace batteries with the same or equivalent type.
• Do not expose batteries to excessive heat (such as sunlight or fire) and to temperatures above 100 °C (212 °F).

Cable Distribution

For this apparatus, the cable shield/screen shall be grounded (earthed) as close as practical to the point of entry of the cable into the building.
For products sold in the USA and Canada: This reminder is provided to call the system installer’s attention to ANSI/NFPA 70, the National Electrical Code (NEC), in  particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable (or Canadian Electrical Code Part 1). The cable distribution system should be grounded  (earthed) in accordance with ANSI/ NFPA 70, the National Electrical Code (NEC), in particular Section 820,93, Grounding of outer Conductive Shield of a Coaxial Cable  (or Canadian Electrical Code Part 1).

Servicing
To reduce the risk of electric shock or electrocution, do not disassemble this product.
If service or repair work is required, take it to a qualified service dealer.

Damage requiring service

Unplug this product from the mains supply socket outlet and refer servicing to qualified service personnel under the following conditions:

• When the power supply, power cord or its plug are damaged.
• When the attached cords are damaged or frayed.
• If liquid has been spilled into the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally.
• If the product has been dropped or damaged in any way.
• There are noticeable signs of overheating.
• If the product exhibits a distinct change in performance.
• If the product is giving off smoke or a burning smell.

Protect the product when moving it
Always disconnect the power source when moving the product or connecting or disconnecting cables.
Interface classifications (upon applicability) The external interfaces of the product are classified as follows:

• Cable (IN/OUT): TNV circuit, not subjected to overvoltages (TNV-1)
• Phone, FXS: TNV (Telecommunications Network Voltage ) circuit, not subjected to overvoltages (TNV-2)
• MoCA, HPNA, RF: TNV circuit, not subjected to overvoltages (TNV-1)
• All other interface ports (e.g. Ethernet, USB,…), including the low voltage power input from the AC mains power supply: SELV (Safety ExtraLow Voltage) circuits.

Regulatory information

North-America – Canada
Notification of Canadian Radio Frequency interference statement
This Class B digital apparatus complies with Canadian ICES-003.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.

Canada – Radiation exposure statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum  distance 30 cm between the radiator and your body.
Canada – Industry Canada (IC) In case this product is equipped with a wireless transceiver, this device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause  undesired operation of the device.

Restricted frequency bands
In case this product is equipped with a wireless transceiver operating in the 2.4 GHz band, it may only use channels 1 to 11 (2412 to 2462 MHz) on Canada territory.
In case this product is equipped with a wireless transceiver operating in the 5 GHz band, it is for indoor use only.
The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended  destination. The firmware setting is not accessible by the end user.
North-America – United States of America Federal Communications Commission (FCC)

Compliancy statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this  device must accept any interference received, including interference that may cause undesired operation.

Responsible Party – U.S. contact information
Technicolor Connected Home LLC, 5030
Sugarloaf Parkway, Building 6, Lawrenceville, GA 30044 USA, 317-587-5466.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Part 15B Supplier’s Declaration of Conformity
The FCC Part 15B Supplier’s Declaration of Conformity (SDoC) for your product is available at the following internet address: www.technicolor.com/ch_regulatory.
FCC radio frequency interference statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and  used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF exposure statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for  satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in the product documentation.
When the product is equipped with a wireless interface, then it becomes a mobile or fixed mounted modular transmitter and must have a separation distance of at least 30 cm  between the antenna and the body of the user or nearby persons. In practice, this means that the user or nearby persons must have a distance of at least 30 cm from the  product and must not lean on the product in case it is wall-mounted. With a separation distance of 30 cm or more, the M(aximum) P(ermissible) E(xposure) limits are well  above the potential this wireless interface is capable to produce.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Restricted frequency bands
In case this product is equipped with a wireless transceiver operating in the 2.4 GHz band, it can only use channels 1 to 11 (2412 to 2462 MHz) on U.S.A. territory.
In case this product is equipped with a wireless transceiver operating in the 5 GHz band, it meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.
The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended  destination. The firmware setting is not accessible by the end user.

Technicolor Delivery Technologies
8-10 rue du Renard, 75004 Paris, France technicolor.com

3774327D
Copyright 2019 Technicolor. All rights reserved.
All tradenames referenced are service marks, trademarks, or registered trademarks of their respective companies. Specifications subject to change without notice. DMS3-SAF-25-466 v5.0.

References

• The Open Source Definition – Open Source Initiative
• Technicolor Home Page
• Files - Vantiva
• Files - Vantiva
• The Open Source Definition – Open Source Initiative

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>