technicolor UIW4054HWC Hotwire Fision TV User Manual

UIW4054HWC

SAFETY INSTRUCTIONS AND REGULATORY NOTICES

BEFORE YOU START INSTALLATION OR USE OF THIS PRODUCT, CAREFULLY READ ALL SAFETY INSTRUCTIONS

Applicability
These Safety Instructions and Regulatory Notices apply to:

• Technicolor Set-Top Boxes

Using equipment safely
When using this product, always follow the basic safety precautions to reduce The risk of fire, electric shock and injury to persons, including the following:

• Always install the product as described in the documentation that is included with your product.
• Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

Important safety instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as a power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Used symbols
Following symbols may be found in this and accompanying documentation as well as on the product or accompanying accessories:

product may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any
inside part of this product.
| This symbol is intended to alert you of the presence of important operating and maintenance (servicing) instructions in the documentation that is included with your product.
| This symbol indicates for indoor use only (IEC 60417-5957).
| This symbol indicates Double insulated Class II equipment (IEC 60417-5172). Does not require an earth connection.
| This symbol indicates Alternating Current (AC).
| This symbol indicates Direct Current (DC).
| This symbol indicates Electrical polarity.
| This symbol indicates Fuse.

Directives
Product use

You must install and use this product in strict accordance with the manufacturer’s instructions as described in the user documentation that is included with your product. Before you start installation or use of this product, carefully read the contents of this document for device-specific constraints or rules that may apply in the country where you want to use this product. If you have any doubts about the installation, operation, or safety of this product, please contact your supplier. Any change or modification made to this product that is not expressly approved by Technicolor will result in the loss of product warranty and may void the user’s authority to operate this equipment. Technicolor disclaims all responsibility in the event of use that does not comply with the present instructions. Software and firmware use The firmware in this equipment is protected by copyright law. You may only use the firmware in the equipment in which it is provided. Any reproduction or distribution of this firmware, or any portion of it, without express written consent from Technicolor, is prohibited. Software described in this ocument is protected by copyright law and furnished to you under a license agreement. You may only use or copy this software in accordance with the terms of your
license agreement. Open Source Software notification The software of this product may contain certain open source software modules which are subject to Open Source Software license terms (see https://opensource.org/osd for definition). Such Open Source Software components and/or versions may change in the future versions of the software product. A list of the Open Source Software used or provided as embedded into the current software of the product and their corresponding licenses and version number are, to the extent required by applicable terms, available on Technicolor’s website at the following address: www.technicolor.com/opensource or at another address as Technicolor may provide from time to time.
If and where applicable, depending on the terms of the applicable Open Source Software licenses, the source code of the Open Source Software is available for free upon request. For avoidance of doubt, Open Source Software is only licensed by the original owner of the Open Source Software under the terms set forth in the
designated Open Source License.

Environmental information
Batteries (if applicable)
Batteries contain hazardous substances which pollute the environment. Do not dispose of them with other articles. Take care to dispose them at special collecting points. Recycle or dispose of batteries in accordance with the battery manufacturer’s instructions and local/ national disposal and recycling regulations.

Energy efficiency
Energy savings
The user documentation that is included with your product not only provides useful information on all the features of your product, but also on its energy consumption. We strongly encourage you to carefully read this documentation before putting your equipment in service in order to get the best service it can offer you.

Safety instructions

• Read these instructions.
• Keep these instructions.
• Heed all warnings and cautions.
• Follow ail instructions.

Climatic conditions
This product:

• Is intended for in-house stationary use; the maximum ambient temperature must not exceed 40 °C (104 °F); the relative humidity must be between 20 and 80 %.
• Must not be mounted in a location exposed to direct or excessive solar and/or heat radiation.
• Must not be exposed to heat trap conditions and must not be subjected to water or condensation.
• Must be installed in a Pollution Degree 2 environment (an environment where there is no pollution or only dry, non-conductive pollution). If applicable, batteries (battery pack or batteries installed) must not be exposed to excessive heat such as sunshine, fire or the like.
  This product is intended for indoor use only.

Ventilation and positioning

This product is intended to be used indoors in a residential or office environment.

• Remove all packaging material before applying power to the product.
• Place and use the product only in positions as  described in the user documentation that is included with your product. In case the product is wall-mountable you can check www.technicolor.com/ch_requlatory for wall mount instructions.
• Never push objects through the openings in this product.
• Do not block or cover any ventilation openings; never stand it on soft furnishings or carpets.
• Leave 7 to 10 cm (3 to 4 inches) around the product to ensure that proper ventilation gets to it.
• Do not install the product near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Do not put anything on it which might spill or drip into it (for example, lighted candles or containers of liquids). Do not expose it to dripping or splashing, rain or moisture. If a liquid enters inside the product, or if the product has been exposed to rain or moisture, unplug it immediately and contact your supplier or customer service.

Cleaning
Unplug this product from the wall socket and disconnect from all other devices before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Water and moisture
Do not use this product near water, for example near a bathtub, washbowIl, kitchen sink, laundry tub, in a wet basement or near a swimming pool. Transition of the product from a cold environment to a warm one may cause condensation on some of its internal parts. Allow it to dry by itself before using the product.

Electrical powering
The powering of the product must adhere to the power specifications indicated on the marking labels. In case this product is powered by a power supply unit:

• For USA: This product is intended to be supplied by a UL listed Direct Plug-in Power Unit marked “Class 2” and rated as indicated on the label on your  product.
• This power supply unit must be Class Il and a Limited Power Source in accordance with the requirements of IEC 60950-1/EN 60950-1, Clause 2.5 or IEC  62368-1/EN 62368-1,
  Annex Q and rated as indicated on the label on your product. It must be tested and approved to national, or local standards.
  Only use the power supply unit that is supplied with this product, is supplied by your service provider or local product supplier, or a replacement power supply unit provided by your service provider or local product supplier.
  The use of other types of power supplies is prohibited.
  If you are not sure of the type of power supply needed, consult the user documentation that is included with your product or contact your service provider or local product supplier.

Accessibility
The plug on the power supply cord or power supply unit serves as disconnect device. Be sure that the mains supply socket outlet you use is easily accessible and located as close to the product as possible. The power connections to the product and the mains supply socket outlet socket must be accessible at all times, so that you always can disconnect the product quickly and safely from the mains supply.

Overloading
Do not overload mains supply socket outlets and extension power cords as this increases the risk of fire or electric shock.

Handling batteries
This product (or its remote control) may contain disposable batteries

CAUTION
There is danger of explosion if the battery is mishandled or incorrectly replaced.

• Do not disassemble, crush, puncture, short the external contacts, dispose of in fire, or expose to fire, water or other liquids.
• Insert batteries correctly. There may be a risk of * Please follow instructions provided for charging rechargeable batteries.
• Replace batteries with the same or equivalent type.
• Do not expose batteries to excessive heat (such as sunlight or fire) and to temperatures above 100 °C (212 °F).

CAUTION
Do not ingest coin or button cell batteries!

Chemical Burn Hazard
This product or remote control supplied with this product may contains a coin/ button cell battery. If the coin/button battery is swallowed, it can cause severe internal burns in just 2 hours and lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Cable Distribution
For this apparatus, the cable shield/screen shall be grounded (earthed) as close as practical to the point of entry of the cable into the building. For products sold in the USA: This reminder is provided to call the system installer’s attention to ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable. The cable distribution system should be grounded (earthed) in accordance with ANSI/ NFPA 70, the National Electrical Code (NEC), in particular Section 820,93, Grounding of outer Conductive Shield of a Coaxial Cable.

Servicing

To reduce the risk of electric shock or electrocution, do not disassemble this product.
If service or repair work is required, take it to a qualified service dealer.

Damage requiring service
Unplug this product from the mains supply socket outlet and refer servicing to qualified service personnel under the following conditions:

• When the power supply, power cord or its plug are damaged.
• When the attached cords are damaged or frayed. explosion if the batteries are incorrectly inserted.
• Do not attempt to recharge disposable or non- reusable batteries.
• If liquid has been spilled into the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally.
• If the product has been dropped or damaged in any way.
• There are noticeable signs of overheating.
• If the product exhibits a distinct change in performance.
• If the product is giving off smoke or a burning smell.

Protect the product when moving it
Always disconnect the power source when moving the product or connecting or disconnecting cables.

Interface classifications (upon applicability)

The external interfaces of the product are classified as follows:

• Cable (IN/OUT): TNV (Telecommunications Network Voltage) circuit, not subjected to over voltages (TNV-1)
• MoCA, HPNA, RF: TNV circuit, not subjected to overvoltage (TNV-1)
• All other interface ports (e.g. HDMI, analog audio/video, Ethernet, USB….), including the low voltage power input from the AC mains power supply: SELV (Safety Extra-Low Voltage) circuits.

Regulatory information
North America – United States of America Federal Communications Commission (FCC)

Compliancy statement
This device complies with Part 15 of the  FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Responsible Party – U.S. contact information
Technicolor Connected Home USA LLC 4855 Peachtree Industrial Blvd. Suite 200 Norcross, GA 30092 USA, 317-587-5466 FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Part 15B Supplier’s Declaration of Conformity

The FCC Part 15B Supplier’s Declaration of Conformity (SDoC) for your product is available at the following internet address:

FCC radio frequency interference statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF exposure statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instructions as documented in the product documentation. When the product is equipped with a wireless interface, then it becomes a mobile or fixed mounted modular transmitter and must have a separation distance of at least 36 cm between the antenna and the body of the user or nearby persons. In practice, this means that the user or nearby persons must have a distance of at least 36 cm from the product and must not lean on the product in case it is wall- mounted. With a separation distance of 36 cm or more, the Maximum Permissible Exposure limits are well above the potential this wireless interface is capable to produce. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Restricted frequency bands
In case this product is equipped with a wireless transceiver operating in the 2.4 GHz band, it can only use channels 1 to 11 (2412 to 2462 MHz) on U.S.A. territory. In case this product is equipped with a wireless transceiver operating in the 5 GHz band, it meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.

UIW4054HWC
QUICK START GUIDE

Contents of the GiftBox

How to start….

Buttons and Physical Connections

1| DC Jack| 2 Pins female standard Jack plug
2.5mm-6.3mm 12V /1.25A
---|---|---
2| HDMI| HDMI OUT
3| Ethernet| RJ-45 /IEEE 802.3 – Unshielded
4| Audio out| SPDIF optical
5| Reset Button|
6| USB bottom| USB 2.0 (Type A) / for accessories
7| Standby Button|
8| Pairing Button|
9| USB side| USB 2.0 (Type A)
10| SD Card reader|

Technical Specifications

remote control type
Conditional Access| NA
External Power Supply Output Voltage /Current| 12V DC /1.25A
Set Top Box Input Voltage /Current| 12V DC /1.25A

TRADEMARKS

The terms HDMI and HDMI High Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and other countries.

Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, Dolby Atmos and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
HEWC – Covered by one or more claims of the patents listed at patentlist.hevcadvance.com.

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Technicolor is under license.
For internal use only (IEC 60417-5957).
Double insulated Class || equipment (IEC 60417-5172). It does not require an earth connection.
Alternative current
Direct current
Polarity
Energy Efficiency DoE Level VI

This product may contain certain open source software modules which are subject to Open Source Software license terms.
A list of the Open Source Software used or provided inside this product and their corresponding licenses and version number are available on TECHNICOLOR’s extranet at the following address: http://www.technicolor.com/en/hi/minisites /open-software or at another address as Technicolor may provide from time to time.
If and where applicable, depending on the terms of the applicable Open Source Software licenses, the source codes of the Open Source Software are available for free on TECHNICOLOR’s website at the following address: hitp://Awww.technicolor.com/en/hi/minisites/open-software
For avoidance of doubt, Open Source Software is only licensed by the original owner of the Open Source Software under the terms set forth in the designated Open Source License.

TCH PN 6304959A

Technicolor Delivery Technologies 8-10 rue du Renard, 75004 Paris, France technicolor.com

Copyright 2021 Technicolor. All rights reserved. All tradenames referenced are service marks, trademarks, or registered trademarks of their respective companies. Specifications subject to change without notice.

References

• Technicolor Home Page

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>