ZEVNI A04884H5 Cohan 27 Chandelier Instruction Manual

: June 9, 2024
: ZEVNI

Table of Contents

SAFETY INSTRUCTIONS
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
ACCESSORIES & QTY ENCLOSED
PARTS TYPE & QTY INCLUDING
ASSEMBLY & INSTALLATION INSTRUCTIONS
ORDERING PARTS
CLEANING
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ZEVNI A04884H5 Cohan 27 Chandelier

ZEVNI A04884H5 Cohan 27 Chandelier

Item Number: A04884H5

SAFETY INSTRUCTIONS

WARNING (To reduce the risk of fire, electric shock, or personal injury):

We suggest installation by a licensed electrician.
Please read the instruction carefully and save it as you may need it at a later time.
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
• Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
• Place the wall switch in the “OFF” position.
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

Image For Finished Product

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

Tools Required | Tools
Required | | |
---|---|---|---|---

Ladder

|

Philips Head or Flat Blade Screwdriver

|

Electrical Tape

|

Pilers

|

Wire Cutter/Stripper

ACCESSORIES & QTY ENCLOSED

(A) Plastic wire connector (3)
(B) Mounting screw (2)

PARTS TYPE & QTY INCLUDING

(C) Mounting plate (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Swivel joint (1)
(G) Knob nut (2)
(H) Tube
(I) Arms assembly (1)
(J) Arm (5)
(K) Socket (5)
(L) Lampshade (5)
(M) Socket ring (5)

Outlet Box

ASSEMBLY & INSTALLATION INSTRUCTIONS

Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
• Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
• Place the wall switch in the “OFF” position.
• Unscrew knob nuts (G) from canopy (E).
• Remove mounting plate (C) and set it aside.
Adjust arms (J) to an equal angle
1) According to your desired hanging height to choose and use tubes (H).
Then pass the fixture wires through the chosen tubes (H), swivel joint (F) and canopy (E).
2) Be sure that all the threaded pipes are tightened, then screw the chosen tubes (H) onto swivel joint (F) and the top of arms assembly (I).
Hand tighten till snug.
Attach mounting plate (C) to the outlet box with mounting screws (B).
Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
• Connect ground wires according to the below chart

• Connect wires according to the below chart
** Connect Black or Red Supply Wire to:| Connect White Supply Wire to:*
---|---
Black| White
Parallel cord (round & smooth)| *Parallel cord (square & ridged)
Clear, Brown, Gold or Black without tracer| Clear, Brown, Gold or Black with tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other than green) with silver conductor

Note : When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
```
* Twist wires together with plastic wire connectors until tightly joined.
* Wrap each connector with approved electrical tape.
* Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box  
```
1. Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening knob nuts (G) onto the pre-assembled screws in mounting plate (C).
  Note: canopy (E) should be snug against the ceiling and knob nuts (G). If not, adjust the threaded length on mounting plate assembly (C):
  - Unscrew the pre-assembled hex nuts.
  - Screw the pre-assembled screws in or out of mounting plate (C).
  - When the secure length is achieved, tighten the hex nuts and back to step 8.
2. 1) Remove socket rings (M) from sockets (K).
  2) Carefully place lampshades (L) on sockets (K).
  3) Secure them with socket rings (M).
  4) Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
3. Check everything is already installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.