Earthquake 15683 Hiller-Furrower Kit Instructions

Instruction Sheet
Hiller/Furrower Kit with Adapters

15683 HILLER/FURROWER KIT (OPTIONAL ACCESSORY)
Thank you for purchasing a Hiller/furrower attachment for your rototiller. We know that you will be pleased with the many uses you can accomplish with this handy tool.

INSTALLATION

1. Attach the bracket (1) to the shovel (4) using two M10 x 40mm carriage bolts (10) and M10 locknuts (11).
   NOTE: The M10 carriage bolts (10) are installed from the front of the shovel (4), while the bracket (1) is installed from the back of the shovel (4).

2. Align the curved slots of the left wing (2) with the square holes on the left side of the shovel (4). The small bend of the left wing (2) should be facing up. Using two M8 x  20mm carriage bolts (9), flat washers (5), external tooth washers (7), and wing nuts (8), secure the left wing (2) to the shovel (4). Repeat step to install the right wing (3).
   NOTE: Adjust the left and right-wing (2, 3) to the correct hill size before tightening the wing nuts (8).

3. Remove two carriage bolts (A) that hold the tail to the tine shield. Slide the slotted end of the bracket (1) over the drag stake mount (under the tail hood of your tiller).

4.  Align the holes in the bracket (1) with the single hole in the middle of the drag stake mount. Using the M10 x 30mm bolt (6) and an M10 locknut (11), secure the  Hiller/furrower to the tiller.
   NOTE: There is an extra M10 x 30mm bolt (6) and M10 locknut (11) that is used for the 25127 adapters only.

5.  Re-attach the tail to the tine shield.

PARTS BREAKDOWN

25126 – Husqvarna Hiller/Furrower Adapter
ASSEMBLY INSTRUCTIONS

1. Remove the standard depth stake on the back of the tiller. SEE FIGURE 1
2. Slide the adapter up into the slot the standard depth stake was in. SEE FIGURE 2
3. Secure the adapter by inserting the pin above the tiller hood into the top hole of the adapter. SEE FIGURE 3
4. Secure the hiller/furrower to the adapter with an M10 x 30mm bolt (6) and M10 locknut (11). SEE FIGURE 4

NOTE: When tightening the hiller/furrower to the adapter, make sure the bracket on the hiller/furrower is in complete contact with the adapter and not tightening to the depth stake mount of the tiller.

ASSEMBLY INSTRUCTIONS

1. Slide the standard drag stake out of the drag stake mount on the back of the tiller and reinstall it, so that the top of the drag stake is now the bottom. SEE FIGURES 1 & 2
2. Re-insert the pin for the drag stake, so that the drag stake end sits flush with the bottom of the mount. SEE FIGURE 2 Place the split side of the adapter over the drag stake and align the holes. Secure the adapter to the standard drag stake with an M10 x 30mm bolt (6) and M10 locknut (11). SEE FIGURE 3 NOTE: This adapter uses the extra M10 x 30mm bolt (6) and M10 locknut (11).
3. Secure the hiller/furrower to the adapter with an M10 x 30mm bolt (6) and M10 locknut (11). SEE FIGURE 4

ASSEMBLY INSTRUCTIONS

1. Remove the bigger bolt that holds on the kick-back stake and set it aside. SEE FIGURE 1
2. Loosen the smaller nut on the kick-back stake to the end of the bolt’s threads. SEE FIGURE 2 NOTE: This allows the adapter to slip into position better.
3. Place the adapter into the square space of the kick-back stake mount. Secure the adapter and kick-back stake to drag stake mount with previously removed bigger bolt. SEE FIGURE 3
4. Once the adapter is in place, tighten up the smaller nut.
5. Place the hiller/furrower bracket on the adapter by sliding the bracket underneath the adapter. The adapter tail must sit on top of the bracket. SEE FIGURE 4
6. Secure the hiller/furrower to the adapter with an M10 x 30mm bolt (6) and M10 locknut (11). SEE FIGURE 4

All weights, specifications, and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Items used for props are not included. Some assembly may be required.
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5

P/N: 25133 ECN: 11711
REV2: 06/20/17
© 2017 Ardisam, Inc.
All Rights Reserved

Documents / Resources

| Earthquake 15683 Hiller-Furrower Kit [pdf] Instructions
15683 Hiller-Furrower Kit, 15683, Hiller-Furrower Kit
---|---

References

• Earthquake | Groundbreaking Power Equipment – Earthquake Outdoor Power Equipment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>