EARTHQUAKE SOUND MiNi D3000.4 2nd Gen Stereo Amplifier User Manual

June 4, 2024
EARTHQUAKE SOUND

SOUND MiNi D3000.4 2nd Gen Stereo Amplifier
User Manual

CAUTION:
Earthquake amplifiers are capable of generating high sound pressure levels. You should exercise caution when operating these amplifier systems.
Long-term exposures to high levels of sound pressure will cause permanent damage to your hearing. Sound pressure
levels exceeding 85dB can be dangerous with constant exposure. Set your audio system to a comfortable loudness level. Earthquake Sound Corporation does not assume liability for damages resulting from the direct use of Earthquake amplifiers or other Earthquake products and urges users to play their music at moderate listening levels.

This chart shows the U.S. Government’s Occupational Safety and Health Administration (OSHA) regulations which were in effect at the time of this publication for permissible noise exposure, per 29CFR1910.95, Table G-16.

SOUND LEVEL dBA DURATION PER DAY (HOURS)
90 8
92 6
95 4
97 3
100 2
102 1 – 1 1/2
105 1
110 2-Jan
115 1/4 OR LESS

Mini D3000.4 Stereo Amplifier

One (1) Year Limited Warranty Guidelines (Valid in US Mainland Only)
A warranty claim will not be valid if the warranty registration card is not properly filled & returned to Earthquake with a copy of the sales receipt.
(E) Service Request:
To receive product(s) service, contact Earthquake Sound’s service department at 510-732-1000 and request an RMA number (Return Material Authorization), item(s) shipped without a valid RMA number will be refused. Make sure you provide us with your complete and correct shipping address, a valid phone number, and a brief description of the problem you are experiencing with the product. In most cases, our technicians might be able to resolve the problem over the phone, thus eliminating the need to ship the product.

(F) Shipping Instructions:
Product(s) must be properly packaged to minimize transport damage and avoid repackaging charges. Shipper claims regarding item(s) damaged in transit must be presented to the carrier. Earthquake Sound Corporation reserves the right to refuse improperly packed product(s). A copy of the original sales receipt must accompany the product(s) returned for service. We encourage you to include a written description of the problem inside the package. Ship product to:

Earthquake Sound Corp.
2727 McCone Avenue
Hayward, CA 94545
Tel: 510-732-1000

You are responsible for the cost of shipping the product to Earthquake Sound Corp.

(G) Disputes Resolution:
All disputes – between clients and Earthquake Sound Corporation – resulting from the one (1) year limited warranty policy must be resolved according to the laws & regulations of the county of Alameda, California.
We strongly suggest keeping a copy of your sales receipt and note the model and serial numbers of your amplifier here for future reference.

Mini D3000.4 Stereo Amplifier
One (1) Year Limited Warranty Guidelines (Valid in US Mainland Only)

Earthquake Sound Corp. warrants the original purchaser that all Factory Sealed New Audio Products be free from defects in material and workmanship, under normal and proper use, for a period of one (1) year from the date of purchase (as shown on the original sales receipt with a serial number affixed/written on it).
The one (1) year warranty period is valid only if the product is properly installed by an Earthquake authorized party, and the warranty registration card is properly filled out and sent to Earthquake Sound Corporation.
If the product is installed by a non-authorized party, a thirty (30) day limited warranty period applies.
(A) One (1) year limited warranty plan coverage guidelines:
Earthquake pays for labor, parts, and ground freight (only in the US mainland, not including Alaska and Hawaii) back to the customer.

(B) Warning:
Products (sent for repair) that are tested by Earthquake technicians and deemed to have no problem, will not be covered by the limited warranty. The customer will be charged a  minimum of one (1) hour of labor (ongoing rates) plus shipping charges back to the customer.
If products were received with improper protective packaging, the customer will be charged product repackaging in addition to labor, parts, and shipping charges.
including Alaska and Hawaii) back to the customer.
(B) Warning:

Products (sent for repair) that are tested by Earthquake technicians and deemed to have no problem, will not be covered by the limited warranty.
Customers will be charged a minimum of one (1) hour of labor (ongoing rates) plus shipping charges back to the customer.
If products were received with improper protective packaging, the customer will be charged product repackaging in addition to labor, parts, and shipping charges.

(C) Earthquake agrees to repair or replace – at our option – all such defective products/parts subject to the following provisions:
Defective products/parts have not been altered or repaired by other than an Earthquake factory-approved technician.
Products/parts are not subjected to negligence, misuse, improper use, or accident, damaged by improper line voltage, used with incompatible products, or have its serial number or any part of it altered, defaced, removed, or have been used in any way that is contrary to Earthquake’s written instructions.

(D) Warranty Limitations:
An earthquake warranty does not cover products that have been modified and/or abused, including but not limited to the following:

  • Fading, deterioration of speaker components & finish due to improper exposure to elements.
  • Bent amplifier casing, damaged finish on the casing due to abuse, misuse, or improper use of cleaning material.
  • Burnt tracers on PCB.
  • Product/part damaged due to poor packaging or abusive shipping conditions.
  • Subsequent damage to other products.

THANK YOU
Thank you for choosing Earthquake Sound’s MiNi D3000.4 stereo amplifier, the best way to enhance your factory mobile audio system. With proper installation and responsible listening, your amplifier(s) will give you years of near- perfect sound reproduction.
We strongly recommend you have your new amplifier(s) installed by an authorized Earthquake Sound dealer. Installation professionals employed by your dealer have the  correct tools and knowledge to install your amplifier(s) neatly and successfully.
Also, when your new products are installed by an authorized dealer, your products will include a ONE (1) YEAR LIMITED WARRANTY. If you choose to perform your own installation, your warranty will be subject to further limitations. Dealer policies on handling warranty requests may vary from one dealer to the next.
Please read the warranty information (located at the end of this booklet)in its entirety and use good judgment when making these vital decisions.

FEATURES AND FUNCTIONS

  1. RCA INPUTS: Low-level input of the D3000.4 is 0.2V to 6V RMS. Be sure to use a HIGH LOW-LEVEL adapter if the head unit has only speaker output.
  2. GAIN / LEVEL CONTROL: Used to adjust the low-level input voltage. It ranges from 0.2V to 6V RMS. It should be set to match the head unit’s output voltage.
  3. X-OVER FREQUENCY ADJUSTMENTS & SWITCHES: Used to adjust the boosted center frequencies.
  4. STEREO/4CH INPUT SWITCH: Available only on the D3000.4, set to “ST” if using 2-channel input and set to “4CH” if using 4-channel input.
  5. PROTECTION LED: When lit up red upon powering on, the amplifier may be in self-test or protection mode. If this LED stays on red, shut down the amplifier and locate what may have triggered the amplifier to protection mode. If the problem persists, call or e-mail our technical support team for further assistance.
  6. POWER LED: When lit up green, the amplifier is functioning properly.
  7. HPF & LPF MULTIPLIERS: These buttons are used to multiply the X-OVER frequencies. When the buttons are engaged the X-OVER frequencies are multiplied by  10. This gives users great flexibility depending on what speakers are installed in the vehicle.

SPECIFICATIONS

For more technical support, please contact:
E-mail: tech@earthquakesound.com
Tel: 510-732-1000

This document should not be construed as a commitment on the part of Earthquake Sound Corporation.
The information is subject to change without notice.
Earthquake Sound Corporation assumes no responsibility for errors that may appear within this document.

Mini D$000.1

Amplifier Class| D
Number of Channels| 4
Max Power Output| 3000 Watts
Power Handling @ 4-Ohm| 4 x 120 WRMS
Power Handling @ 2-Ohm| 4 x 200 WRMS
Power Handling – Bridged @ 4-Ohm| 2 x 300 WRMS
THD+N| < 1%
Channel Separation| > 90 dB
Crossover Frequencies| HPF 20-400Hz
LPF 50-400Hz
Signal-to-Noise Ratio| 98 dB
Fuse Rating| 2 x 40A (Included)
ALL OUTPUT POWER MEASUREMENTS ARE MADE WITH A DUMMY LOAD FOR THE RMS MEASUREMENTS.  DUMMY LOADS ARE HARDER TO DRIVE THAN SPEAKERS AND DEMAND MORE POWER SUPPLY CURRENT.

FEATURES AND FUNCTIONS

8. SPEAKER TERMINALS: Bridgeable speaker outputs. Note that the minimum impedance is bridged mode is 4-Ohm.
9. FUSES: Available only on the D3000.4, these 2 x 40A fuses are used as an added protection from damaging excessive current. Be sure to use the proper fuse rating
in your installation.
10. +12V BATTERY TERMINAL: Used to connect to the battery on the positive (+) using a 4 gauge cable..
11. REMOTE TERMINAL: Used to connect a remote cable to the head unit’s remote terminal. If multiple amplifier are installed in the system, additional relays  may be necessary.
12. GROUND TERMINAL: Used to connect to the vehicle’s chassis/ground using a short 4 gauge cable (2 feet maximum in length).

NOTE: Be sure to follow the wiring preparations/guidelines as listed on the next page to ensure proper installation.
WARNING: Make sure that the amplifier is completely off and not connected to any power source during the wiring process. Failure to do so may result in a short that can cause damage to the amplifier or personal injury.

WIRING PREPARATIONS

  • Test the alternator output. Factory alternators will produce 60–80 amperes at best. Wear and heat will reduce the output by 40%.
  • Alternator ground (-) must be reinforced. Use a 4-gauge cable instead of the factory 8-gauge.
  • Alternator positive (+) to a battery (+) must be reinforced. Use 4-gauge cables.
  • Check your battery condition as batteries degrade after a while.
  • Battery (+) to the amplifier (+) must be connected using a 4-gauge cable.
  • Ground amplifier to vehicle’s chassis (bare metal) using a 4-gauge cable, keep the cable short (2 feet max).
  • Use 1 Farad capacitor to compensate for surges in demand.
  • We recommend the use of one (1) auxiliary battery.

WARNING: Make sure that the amplifier is completely off and not connected to any power source during the wiring process. Failure to do so may result in a short that can cause damage to the amplifier or personal injury.

Mini D3000.4 WIRING CONFIGURATIONS FRONT STEREO & REAR FILL

Mini D3000.4 WIRING CONFIGURATIONS
2.1 SYSTEM APPLICATION

BASS APPLICATION (BRIDGED 4-OHM MINIMUM

WARNING: Make sure that the amplifier is completely off and not connected to any power source during the wiring process. Failure to do so may result in a short that can cause damage to the amplifier or personal injury.

www.earthquakesound.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

EARTHQUAKE SOUND User Manuals

Related Manuals