rizoma PT325 License Plate Holder User Manual
- June 9, 2024
- rizoma
Table of Contents
rizoma PT325 License Plate Holder
Before you start
We are pleased to welcome you into the world of RIZOMA, and we congratulate you for your excellent choice. Please carefully follow the instructions in this guide, which will allow you to mount and use the product correctly and enjoy all the features it has. For your protection and safety, RIZOMA expressly recommends that you have the installation of the product performed by skilled personnel. Improper installation, repair or maintenance, can cause accidents. Keep this user guide as a reference for the future. RIZOMA accepts no liability for any damage, of any kind, which may be caused, directly or indirectly, to persons or things as a result of incorrect assembly or failure to observe all the assembly instructions. We also invite you to comply with the provisions of the Highway Code and Traffic rules and/or to additional regulations in force in your Country.
Attention: This component comes assembled for shipping purposes only.
Tighten all fasteners to appropriate torque specifications before riding.
Descriptions preceded by this symbol contain information, instructions, or
procedures, which, if not followed, may result in death or serious injury.
- Carefully read, understand and follow these instructions, they are an essential part of the product. If you have any doubt whatsoever regarding the installation or use of your RIZOMA product, please see your authorized RIZOMA dealer for assistance (on www.rizoma.com).
- For correct installation, all tightening has to be done after the correct positioning of the accessories without restricting the moving parts, to not compromise the correct functioning of the product.
- After installing any Rizoma product, please check that all related components of the motorbike function e.g. brakes, throttle, clutch, lights and steering. We strongly suggest to repeat these checks periodically, especially after long trips or prolonged periods of not using the bike.
Your RIZOMA products require regular inspection and maintenance. The more you
ride the more often you must inspect your RIZOMA products. If your products
are leaking, bent, deformed, cracked, chipped or worn, no matter how slight,
immediately have a RIZOMA dealer inspect the products before you ride again.
In any case never try to repair or modify the Rizoma products or their
components, always replace with Rizoma original components.
Rizoma products may not be compatible with your motorcycle or with other
aftermarket equipment installed before. For your safety Rizoma suggests to
always contact your RIZOMA dealer.
O.E.M.: original equipment manufacturer.
License plate
PART NUMBER
PT325
To comply with the TÜV and European Norm in force, the installation of the license plate must be carried out as the enclosed instructions. Consult the website www.rizoma.com, in license plate support section click “MEDIA” to download the PDF document approval ABE. Before you start mounting the product please check the completeness of the kit on the part list. The difficulty level and the time of assemblage shown do not include the removal of OEM components.
Warning: Make sure that your motorbike is standing firmly before you start work, as a fall may lead to damage to the motorbike or injury to you or others, also make sure that the temperature of the exhausts and the engine are similar to the ambient temperature.
WARNING: TO CLEAN YOUR LICENSE PLATE DON’T USE DETERGENT, AGGRESSIVE
PRODUCTS OR ABRASIVE SPONGE THAT CAN DAMAGE OR SCRATCH YOUR LICENSE PLATE, BUT
USE ONLY NEUTRAL DETERGENT WITH COLD WATER. 
Improper installation could
damage the electrical system of the motorcycle and cause a fire, resulting in
personal injury or death. Electrical shock hazard. Disconnect the battery
before starting to install turn license plate bracket or rear light or the
turn signals. The pins must always be isolated and respect the polarity in the
connections. The warrantee is not valid for any electric wires cutting or any
product modify or tampering. 
REMOVE ORIGINAL LICENSE PLATE
Step 1
INSTALL SUPPORT
Step 2
INSTALL PLATE FOR MEDIUM/LARGE LICENSE PLATE
Step 3
INSTALL PLATE FOR SMALL LICENSE PLATE
Step 4 INSTALL UNIVERSAL LICENSE PLATE
Step 5 INSTALL PIN OF POSITIONING
Step 6 INSTALL LICENSE PLATE
Step 7 INSTALL INDICATORS
Step 8 INSERT WIRINGS
Step 9 ALL LICENSE PLATE ON UNDER SEAT
Step 10 Step 11
ADJUSTMENT LICENSE PLATE
Step 12
ADJUSTMENT REFLECTOR
Step 13
CONNECTIONS
Step 14
RIZOMA reserves the right, in its sole discretion, to make changes to the product and this information at any time and without prior notice. Although many catalogs and advertisements depict riders engaged in extreme or stunt riding, this activity is extremely dangerous, increases the risk of an accident, and increases the severity of any injury.
The action depicted is performed by professionals under strictly controlled
riding conditions.
Only you know the limits of your riding ability and only you can control the
conditions under which you ride. By and in consideration for his/her purchase
and use of the RIZOMA product, the user expressly recognizes and agrees that
in the event of any claim arising out of the use of this RIZOMA product,
whether such claim is based in contract, warranty, tort (personal injury or
wrongful death) or otherwise, the laws of the Republic of Italy shall apply
and jurisdiction and venue for any such action shall be in the Courts of Busto
Arsizio, Italy.
All riders are strongly urged to take a motorcycle rider safety clinic. Always wear a properly fitted and fastened motorcycle helmet (RIZOMA recommends a full face helmet), that has been approved by ANSI , SNELL, CE, or any other relevant authority, and any other safety equipment necessary for your riding style, such as full finger gloves, boots, and body armor.
Be sure to read and follow all the instructions and warnings that originally accompanied your motorcycle, as well as the literature that accompanied any other component parts installed on your motorcycle.
Be sure that your tires are inflated to the correct pressure and that there is no damage whatsoever in the tread or sidewall of the tire.
Some of our products may not be approved for road circulation in the countries where homologation is required. Thus RIZOMA® srl declines any responsibility for a different use of its products.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>