Optelec COMPACTGO Wireless Charger of Compact Go Instruction Manual
- June 9, 2024
- Optelec
Table of Contents
Optelec COMPACTGO Wireless Charger of Compact Go
IMPORTANT INSTRUCTIONS
When using this product, basic precautions should always be followed, including the following:
- Read all the instructions before using the product.
- Do not press this product without proper protection, otherwise, it may damage it.
- This product is intended for use in class 2 or LPS circuit in the final products.
- Do not clear this product with wet cloth and the like.
- Do not disassemble or modify this product in any way.
- Do not locate at wet place, always ensure this product is used in a dry location area.
- For indoor use only.
- To avoid risk of fire, do not expose this product to excessive heat or direct sunlight.
- Use the product in environments where the temperature is between 10℃and 35℃.
- To avoid the risk of electrical damage, keep this product away from fluids and chemicals.
- Always unplug the product before cleaning. Use a cleaning cloth or a soft damp cloth to clean the exterior. Do not use cleaning agents or abrasive material, as they will damage this product.
SAVE THESE INSTRUCTIONS
PRODUCT DESCRIPTION
Main Machine
Product name: Wireless Charger of Compact Go
Product model/Type: Wireless Charger of Compact Go Wireless Output: 5W
Power adapter (Not included with the product)
Input: 100-240V ac. 50/60Hz
Output: DC 5V 3.0A
Max. Operating ambient temperature: 35 °C or higher Operation altitude: Up to
5000m
LPS output
Approved by IEC 62368-1 & EN 62368-1
GENERAL DESCRIPTION
CHARGE THE PRODUCT
The battery MUST be fully charged before FIRST use with the supplied power
adapter. There are two charging methods: wireless charging and wired charging.
Wireless Charging: Connect the adapter with the wireless charger. Put
Compact go on the wireless charger and make sure the camera is in the camera
slot, and the handle in the handle slot.
Wired Charging: Connect the adapter directly to the Compact go via the
USB-Type C port on the top edge of Compact go.
The power indicator light is flashing green while the device is charging. When
the battery is fully charged, the power indicator light will be constant
green. When the battery is low, the “low battery” icon will be shown on
the screen and then the product will be shut down.
BASIC OPERATION
-
Open the Handle
Swing out the handle clockwise on the back of the Luna 6. Within 0° to 180°, the handle can stay at any position. Open the handle according to the illustration in the figure below.
-
Power on/off
Press the Power button for 5 seconds to turn the product on. You can turn the device off in the same way.
The device will shut down automatically after 3 minutes of inactivity. You can deactivate this power saving function in System Settings. Please refer to section “Power Saving” . -
Zoom Control
Press Zoom in button to increase magnification and press Zoom out button to decrease magnification. -
Select Color Mode
The default color mode includes 22 colors: Black yellow, yellow black and white with black, white/black, black, green, green, black, white, blue, white, blue, blue, black, blue black, blue and yellow, blue and yellow, red and black, red and black, black, tan brown black, black, purple, purple, black, red, white, white with red, black light blue words, Black writing on a light blue background.
You can choose your favorite color mode in the Settings in Main Menu. Please refer to section “Color Mode”. -
Freeze
-
Freeze an Image
Press the Freeze button to capture an image. Press the Zoom in or Zoom out buttons to change the magnification level of a frozen image, or Mode button to change colors. -
Panning
You can use panning function to pan magnified images by moving them vertically and horizontally across the display area to view specific areas of the image.
After capturing an image, press the Zoom in button to magnify it. Press and hold the Home button along with any of the Freeze/Mode/Zoom out/Zoom in buttons to move the image up/down/left/right respectively. Short press these buttons to move the image a little bit at a time, or hold the buttons to pan continuously. -
Save an Image
Long press the freeze button for 3 seconds to save the frozen image.
If “memory is full” is displayed on the screen, it means the memory is full and some pictures need to be deleted if you would like to save new ones.
ADVANCED OPERATION
Main Menu
In the real-time view, short press Home button to activate the Main Menu.
There are a few options in the Main Menu: Gallery, LED lights, Screen
brightness, Color mode, Reading line and masks, System settings.
To select an option in the menu, move the Zoom in/out button to cycle through
the icons, and press the Mode button to confirm.
Press the Freeze button to go back. Press the Home button to go back to the
real-time view directly.
LED Lights
Press THE MENU key TO OPEN the main menu, select the light icon, press the
color mode key once to open the light, and press the light again to close it
Screen Brightness
Choose this option to adjust the screen brightness. In the Screen Brightness
setting, press Zoom in/out buttons to change the screen brightness, and press
the Mode button to confirm.
Intensity of Contrast
The crispness of text in high-contrast color mode can be affected by the
lighting conditions and the reading material itself. This product enables you
to change the intensity of contrast color to ensure the best reading
experience.
In the Intensity of Contrast setting, press Zoom in/out buttons to change the
intensity, and press the Mode button to confirm.
Reading Line or Masks
- In the Reading line or Masks setting, press the Zoom in/out button to cycle through five reading lines and masks options. Once it’s done, press the Freeze button or Home button to exit.
- In real-time view, you can also press Zoom in and Zoom out buttons to activate reading line and masks.
- Hold the Home button and press Zoom in/Zoom out button simultaneously to adjust the line position or the width of reading masks.
Color Mode
- In the Color Mode setting, you can hide the high-contrast colors you do not use often.
- Press Zoom in/out button to move between the colors. Press the Mode button to select or deselect a specific color mode. A cross mak on an icon means the color mode chosen is hidden. Once it’s done, press the Freeze button or Home button to exit.
Gallery
In the Gallery, press the Zoom in/out buttons to cycle through the images,
then press the Mode button to confirm and view the image selected.
You can change the color mode by pressing the Mode button or view details of
the image using the panning function.
Press the color mode key to select a picture, and two ICONS will appear on the
screen: Open and delete. Press the + – key to select ICONS, and press the
color mode key to confirm. After deleting the icon, the previous picture will
be hidden and automatically displayed 1 second later.
System Settings
System Settings is the last option in the Main Menu. It is recommended to
consult your supplier for system settings.
To select an option in the System Settings, move the Zoom in/out button to
cycle through the icons, and press the Mode button to confirm. Press the
Freeze button to go back, or the Home button to exit.
Sound
The sound screen has four options, which are off, low, medium, high, and
medium by default.
Firmware Version
This option shows the software version of this product.
Time setting
It can set operation duration through it.
Power Saving
By default, this product will shut down automatically after 3 minutes of
inactivity.
To enable or disable the power saving, use the icon Z under system setings to
choose between 2 options in the Power Saving setting. Once you turn this
function off, this product will keep on until it runs out of battery.
Refresh Rate
To change the refresh rate, choose the 60Hz/50Hz icon (it will display either
60Hz or 50Hz) and press Mode button to enter settings. Press Zoom in/out
button to choose between the 2 options.
The default refresh rate is 60Hz.
Restore Factory Settings
Use this function to restore the factory settings of this product.
OTHER OPERATION
Connect to TV or Monitor
To view images on a larger screen, use the supplied HDMI cable to connect this
product to an HDMI TV or monitor. For most TVs, it will be necessary to change
the input source to view the image from this proudct. Once connected, the
image from this product will be shown on your TV or monitor.
FCC statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. During the operation of
device a distance of 15 cm surrounding the device and 20 cm above the top
surface of the devicemust be respected.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>