Stealth Products P72D632R2 Chest Straps User Manual
- June 9, 2024
- Stealth Products
Table of Contents
Thoracic Support
Chest Straps
Intended Use
The Stealth Positioning™ line of pelvic belts, vests, chest straps and foot
positioners are intended to help wheelchair users attain proper alignment of
the torso, pelvis and feet. Comfort, stability and improved clinical posture
are achieved through the use of breathable material and structured support.
Thoracic positioning impacts proper posture and safety. Thoracic trunk
supports are placed in front of the user’s torso and are designed to keep the
trunk aligned with the back of the seating system. A properly positioned
trunk allows for
- Improved respiratory capacity;
- Good visual field;
- Proper head positioning and neck alignment;
- Improved overall pressure distribution;
- The reduction of negative postural tendencies that can lead to orthopedic deformities and other secondary medical complications; and,
- A balance between support and function.
Installation and Use
Stealth Positioning™ chest straps are a form of anterior thoracic (frontal
upper body) support designed to help users with minimal positioning
requirements maintain trunk stability and proper upright alignment. Using a
chest strap provides support across the chest without crossing the shoulders
and does not prevent flexion above the strap, providing more functional reach
than a harness or shoulder straps. The dynamic material also provides some
assistance with returning to an upright position.
Fasten tri-ends to the seat back with included fasteners and attach the belt
to the tri-end. This will allow proper adjustment of the tension
straps.
Hook and Loop
The Hook-and-Loop attachment system is available for Stealth Positioning™
Chest Belts.
Step 1: To release the belt, grasp the webbing strap on the top pad and
peel it forward, away from your chest and the bottom pad.
Step 2: To adjust the fit of the belt, shorten or lengthen the straps
using the tri-end on the back of your chair. Make sure the pads overlap by at
least half of the length of the pad when fitted to the user.
Step 3 : To reattach the belt, press the pad with the hooks firmly on top
of the pad with the loops in the center of the user’s chest and level with the
mount points on the chair back.
Side-Release Buckle
The Side-Release Buckle is used on these Stealth Positioning™ products:
Pelvic Belts | Backpack Straps |
---|---|
Shoe Holders Chest Straps | Positioning Systems |
Chest Straps | Foot Positioners |
Step 1: To remove the side-release buckle from the belt, pinch the
buttons on the sides of the buckle. This will disengage the locking mechanism.
Step 2: Slide the male portion of the buckle from the housing. Make any
adjustments necessary.
Step 3: To reattach the side-release buckle, slide the male portion of
the buckle into the housing. A audible ‘click’ should occur, indicating that
the belt is secure.
If the buckle does not latch and hold, immediately refrain from using the
product.
Care and Cleaning
We recommend that all products be examined on a regular basis for wear and
function. Check the stitching on the webbing for stress or damage. If loose,
frayed or broken parts are discovered, discontinue use and contact your
provider. Repairs should only be performed by a wheelchair service
professional and with genuine Stealth Products parts, fasteners or items
appropriate for the service required.
Surfaces may be cleaned with a damp cloth and a mild, non-abrasive cleaner.
Ensure all cleaners are approved for finished steel, aluminum, plastic and
upholstered surfaces. Vests and straps that are removable and DO NOT contain
metal components may be machine washed warm (40°C), permanent press cycle,
mild process.
DO NOT bleach. DO NOT tumble dry. Dry flat. DO NOT iron.
Important
Never use a chest harness without a positioning belt. Positioning belts and
supports should only be used to help support the user’s posture. The belts,
posture supports and straps must be snug, but must not interfere with the
user’s breathing. Check to make sure the user cannot slide down in the seating
system, as they may suffer chest compression and may suffocate due to
pressure from the belts or harnesses. A seat with angle or built-in contours
may help prevent the user from sliding in the seat.
Due to the possibility of a user sliding while in-chair, unsupervised use of
anterior thoracic support devices could pose a serious choking hazard.
Continually ensure that the user is sitting upright and that the thoracic
support device does not obstruct the user’s breathing in any way.
These devices do not conform to ANSI/RESNA WC20 or SAE J2249 and are not
designed or approved to provide restraint or protection in the event of a
crash. Wheelchair users should transfer to a vehicle seat and use the vehicle
seat belt system or a child safety seat that complies with federal safety
standards. The wheelchair should then be stored and secured in the vehicle.
Children weighing less than 48 lbs. must always transfer to an approved child
safety seat.
Before you install or begin using any product from Stealth Products’ Stealth
Positioning™ line, it is important that you read and understand the content of
these installation and operating instructions. Product misuse due to failure
to adhere to instructions and warnings in this document will void your
warranty and may result in property damage, injury or death. Always keep the
operating instructions in a safe place so they may be referenced as necessary.
If this document contains information you do not
understand or if there are concerns about safety or operation, contact your
provider.
All information, pictures, illustrations and specifications are based on the
product information available at the time of printing, and are representative
examples. They are not intended to be exact descriptions of the various parts
of the product. Instructions are written with the expressed intent of use with
standard configurations. They also contain important safety and maintenance
information. For assistance with advanced configurations or options, contact
your provider or Stealth Products at
512-715-9995 or toll free at
800-965-9229.
Immediately discontinue use if any function is compromised, if parts are
missing or loose or if any component shows signs of excessive wear. Consult
with your provider for repair, adjustment or replacement. You can download
additional copies of this manual by visiting
https://stlpro.site/stealthdocs/ and searching for “Stealth Positioning” in
the document manager.
Warranty
Our products are designed, manufactured, and produced to the highest of standards. If any defect in material or workmanship is found, Stealth Products will repair or replace the product at our discretion. Any implied warranty, including the implied warranties of merchantability and fitness for a particular purpose, shall not extend beyond the duration of this warranty. Stealth Products, LLC does not warrant damage due to, but not limited to, misuse, abuse, or misapplication of products and modification of product without written approval from Stealth Products, LLC.
Any alteration or lack of serial number, where applicable, will automatically
void this warranty. Stealth Products, LLC is liable for replacement parts
only. Stealth Products, LLC is not liable for any incurred labor costs. No
person is authorized to alter, extend, or waive the warranties of Stealth
Products, LLC.
To learn more about our warranty and returns policy, please visit
https://stlpro.site/returns-n-warranty.
About Us
Stealth Products is committed to 100% customer satisfaction. Your complete
satisfaction is important to us. Please contact us with suggestions or
feedback to help us improve the quality and usability of our products.
You may reach us at:
Stealth Products, LLC
104 John Kelly Drive,
Burnet, TX 78611
Phone: 512-715-9995 Toll Free:
800-965-9229
Fax: 512-715-9954 Toll Free:
800-806-1225
info@stealthproducts.com –
www.stealthproducts.com
MDSS GmbH
Schiffgraben 41
30175 Hannover, Germany
SODIMED SA
Chemin Praz Devant 12
1032 Romanel sur-Lausanne, Switzerland
UK Authorized Representative
MDSS-UK RP
6 Wilmslow Road, Rusholme
Manchester M14 5TP, United Kingdom Oct 28, 2022
P72D632R2 SP IF