Stealth Products P72D634R2 Leg Support Calf Straps and Panels Installation Guide
- June 3, 2024
- Stealth Products
Table of Contents
STEALITH POSITIONING
Leg Support
Calf Straps and Panels
P72D634R2 Leg Support Calf Straps and Panels
Intended Use
The Stealth Positioning™ line of pelvic belts, vests, chest straps and foot
positioners are intended to help wheelchair users attain proper alignment of
the torso, pelvis and feet. Comfort, stability, and improved clinical posture
are achieved through the use of breathable material and structured support.
Stealth Positioning™ Calf Straps and Panels are designed to add posterior
support for the lower legs and feet in chairs that do not provide this type of
support, or that could use extra support above the ankle. It provides extra
security in situations where tilt or jarring might cause unintentional flexion
of the lower leg into the space beneath the seat, possibly leading to
accident or injury as well as keeping the feet positioned over the footplate.
The straps and panels provide
- structured, flexible support for the lower legs;
- prevention pressure sores by using a soft, durable proprietary material with stitched edges;
- a hook-and-loop fastening system that holds fast, but is easy to adjust;
- a tactile reminder of leg position for users and attendants; and,
- additional security in chairs that tilt or are driven on uneven terrain.
Installation and Use
Stealth Positioning™ Calf Panels or Calf Straps have been designed to fit most wheelchairs. Installation is fast and easy.
- There are either two or four hook and loop flaps that must be loosened, depending on the type of strap or panel. Pull the hooks away from the loop material. They will open more easily if you pull from the tip of the flap to the base of the flap.
- Place the strap or panel behind the user’s legs in a mid-calf position in front of the footrest down-tubes of the wheelchair. Center the strap or panel evenly between the tubes.
- Wrap the flaps firmly around and behind the down-tubes, pressing against the back of the strap to engage the hook and loop material.
- The strap or panel should now be properly installed and should resemble the image in Figure 1, on the next page.
When seated in an neutral position, the panel should neither impede the ability of the user to put their feet comfortably on the footrests, nor allow the users feet to pass behind the footrests. Adjusting the strap in this way will allow the strap to support the legs when the user is reclined or tilted.
Care and Cleaning
We recommend that all products be examined on a regular basis for wear and
function. Check the stitching on the webbing for stress or damage. If loose,
frayed or broken parts are discovered, discontinue use and contact your
provider. Repairs should only be performed by a wheelchair service
professional and with genuine Stealth Products parts, fasteners or items
appropriate for the service required.
Surfaces may be cleaned with a damp cloth and a mild, non-abrasive cleaner.
Ensure all cleaners are approved for finished steel, aluminum, plastic and
upholstered surfaces. Vests and straps that are removable and DO NOT contain
metal components may be machine washed warm (40°C), permanent press cycle,
mild process.
DO NOT bleach.
DO NOT tumble dry.
Dry flat. DO NOT iron.
Important
Never use a chest harness without a positioning belt. Positioning belts and
supports should only be used to help support the user’s posture. The belts,
posture supports and straps must be snug, but must not interfere with the
user’s breathing. Check to make sure the user cannot slide down in the seating
system, as they may suffer chest compression and may suffocate due to
pressure from the belts or harnesses. A seat with angle or built-in contours
may help prevent the user from sliding in the seat. Due to the possibility of
a user sliding while in-chair, unsupervised use of anterior thoracic support
devices could pose a serious choking hazard. Continually ensure that the user
is sitting upright and that the thoracic support device does not obstruct the
user’s breathing in any way.
These devices do not conform to ANSI/RESNA WC20 or SAE J2249 and are not
designed or approved to provide restraint or protection in the event of a
crash. Wheelchair users should transfer to a vehicle seat and use the vehicle
seat belt system or a child safety seat that complies with federal safety
standards. The wheelchair should then be stored and secured in the vehicle.
Children weighing less than 48 lbs. must always transfer to an approved child
safety seat.
Before you install or begin using any product from Stealth Products’ Stealth
Positioning™ line, it is important that you read and understand the content of
these installation and operating instructions. Product misuse due to failure
to adhere to instructions and warnings in this document will void your
warranty and may result in property damage, injury or death. Always keep the
operating instructions in a safe place so they may be referenced as necessary.
If this document contains information you do not understand or if there are
concerns about safety or operation, contact your provider.
All information, pictures, illustrations and specifications are based on the
product information available at the time of printing, and are representative
examples. They are not intended to be exact descriptions of the various parts
of the product. Instructions are written with the expressed intent of use with
standard configurations. They also contain important safety and maintenance
information. For assistance with advanced configurations or options, contact
your provider or Stealth Products at
512-715-9995 or toll free at
800-965-9229.
Immediately discontinue use if any function is compromised, if parts are
missing or loose or if any component shows signs of excessive wear. Consult
with your provider for repair, adjustment or replacement. You can download
additional copies of this manual by visiting
https://stlpro.site/stealthdocs/ and searching for “Stealth Positioning” in
the document manager.
Warranty
Our products are designed, manufactured, and produced to the highest of
standards. If any defect in material or workmanship is found, Stealth Products
will repair or replace the product at our discretion. Any implied warranty,
including the implied warranties of merchantability and fitness for a
particular purpose, shall not extend beyond the duration of this warranty.
Stealth Products, LLC does not warrant damage due to, but not limited to,
misuse, abuse, or misapplication of products and modification of product
without written approval from Stealth Products, LLC.
Any alteration or lack of serial number, where applicable, will automatically
void this warranty. Stealth Products, LLC is liable for replacement parts
only. Stealth Products, LLC is not liable for any incurred labor costs. No
person is authorized to alter, extend, or waive the warranties of Stealth
Products, LLC.
To learn more about our warranty and returns policy, please visit
https://stlpro.site/returns-n-warranty.
About Us
Stealth Products is committed to 100% customer satisfaction. Your complete
satisfaction is important to us. Please contact us with suggestions or
feedback to help us improve the quality and usability of our products.
You may reach us at:
Stealth Products, LLC
104 John Kelly Drive,
Burnet, TX 78611
Phone: 512-715-9995 Toll Free:
800-965-9229
Fax: 512-715-9954 Toll Free:
800-806-1225
info@stealthproducts.com –
www.stealthproducts.com
MDSS GmbH
Schiffgraben 41
30175 Hannover, Germany|
SODIMED SA
Chemin Praz Devant 12
1032 Romanel sur-Lausanne, Switzerland| UK Authorized Representative
MDSS-UK RP
6 Wilmslow Road, Rusholme
Manchester M14 5TP, United Kingdom
---|---|---
P72D634R2 © 2022, Stealth Products, LLC.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>