ISOtunes 859571006559 Free Aware Wireless Earbuds Instruction Manual
- June 9, 2024
- ISOtunes
Table of Contents
THE NEXT GENERATION OF HEARING PROTECTION™
Location of Controls
Left Earbud Touch Surface Functionality| Right Earbud Touch Surface
Functionality
---|---
Aware Technology
UP (+): Single Tap
DOWN (-): Double Tap| Music
Play/Pause: Single Tap
Next Track: Double Tap
Previous Track: Triple Tap
Phone Call
Answer: Single Tap
End/Reject Call: Long Press
Mute/Unmute Microphone: Single Tap
No music volume control. Music/phone call volume is controlled by the device (ie. smartphone)
Aware Technology™
This product includes Aware Technology. This is a microphone technology that
allows the user to hear the world around them, but always at a safe listening
level. When ambient noise breaches a safe listening level, the microphone
technology immediately responds and attenuates to a safe level.
Adjusting the Aware Volume is easy. Simply tap the left earbud (2L) once for
Aware Volume Up and tap the left earbud (2L) twice for Aware Volume Down.
Charging the Earbuds
There are three batteries to charge:
- Charging Case Battery
- Left Earbud Battery
- Right Earbud Battery
Place earbuds into the charging case. The earbuds’ LED Indicator Light (3) should be solid red, indicating that the earbuds are charging (if the LED Indicator Light (3)) doesn’t appear, refer to the troubleshooting section at the end of this manual).
Earbud LED Indicator Light (3)
Solid Red = Charging
(Earbuds in case)
Solid Blue = Fully Charged
(Earbuds in case)
Charging the Case
Insert USB C charging cable to charge the case. The Charging Case Battery Indicator Lights will start flashing to indicate the charge level.
Charging Case Indicator Light
| 25% Battery Life
50% Battery Life
75% Battery Life
100% Battery Life
---|---
IMPORTANT CHARGING INFORMATION
Please charge with the included USB C cable by plugging it into the Charging
Port. *Charging voltage should not exceed 5v.
Power On/Off
Method 1
Power On: Open the charging case. The earbuds will power on.
Power Off: Place the earbuds into the charging case and close the case.
The earbuds will power off.
Method 2
Power On: In OFF MODE, touch and hold R earbud (2R) until you hear “Power
On” this will turn on your R earbud. Repeat with other earbud (2L) (est. time
three seconds)
Power Off: In ON MODE, touch and hold R earbud (2R) for 5 seconds until you hear “Power Off” this will turn off your R earbud. Repeat with other earbud (2L) (est. time five seconds)
Earbud LED Indicator Light (3)
Blue Flash = Power ON
Red Flash = Power OFF
Bluetooth Pairing
After powering on, the headphones will automatically enter Pairing Mode.
You will hear “Bluetooth Pairing Mode” and the LED Indicator Light (3) will
flash, alternating Blue and Red on both earbuds.
Earbud LED Indicator Light (3)
Red/Blue Flash = Pairing Mode
A
Open your Bluetooth settings on your device.| B
Search “ISOtunes FREE Aware.” Pair and connect.
Once connected you will hear “Bluetooth Connected.”
---|---
|
Music (Right Earbud Control)
Play/Pause: Single tap of the Touch Surface (2)
Next Track: Double tap of the Touch Surface (2)
Previous Track: Triple tap of the Touch Surface (2)
Volume Control
Music and phone call volume control is controlled by the paired device (ie. smartphone)
Phone Calls (Right Earbud Control)
Answer/End Call: Single Tap Right Earbud
Reject Call: Long Press Right Earbud
End Call: Long Press Right Earbud
Place on Hold/Switch Calls on Hold: Double Tap Right Earbud
Mute/Unmute Microphone: Single Tap Right Earbud
Siri / Google Assistant
Press and hold Touch Surface (2) for 1 second.
Troubleshooting
Fitting
- Carefully compress the foam eartip on the stem/sound port.
- Insert the eartip into your ear as deeply as comfortable.
- Slightly rotate earbud until it is secure in the bowl of your ear.
- Make the earbud rest tightly next to your inner ear edge.
Factory Reset
For issues with with powering off, pairing, or touch surface functionality we recommend a factory reset. As a result, Bluetooth will be disconnected and the device will need to be repaired.
- Remove “ISOtunes FREE Aware” from your paired Bluetooth devices in your smartphone.
- Press and hold the battery life indicator button on the back of the case for ten seconds with both earbuds in the case.
- LED lights on the charging case will flash to indicate a successful pairing reset.
- Follow Bluetooth Pairing Instructions to re-pair your device.
Legalities Fitting
ANSI S3.19-1974 Table (NRR Table)
Frequency. Hz| 125| 250| 500| 1000| 2000|
3150| 4000| 6300| 8000| NRR
---|---|---|---|---|---|---|---|---|---|---
Grand Mean Attenuation| 30.7| 28.3| 33.7| 33.5| 32.9| 33.9| 35.9| 40.1| 42.7|
25
Frequency Hz| 5| 3.4| 5| 3.3| 2.5| 2.4| 4.3| 2.6| 2.1
EN352-2:2002 Table (SNR Table)
B1: Frequency, Hz| 125| 250| 500| 1000| 2000|
4000| 8000
---|---|---|---|---|---|---|---
82: Mf (dB)| 28.5| 31.8| 34.9| 34.6| 33.4| 40.2| 45.2
93: sf (dB)| 4.2| 4| 5.1| 5.1| 3.6| 4.6| 3.5
B4: APVf| 24.3| 27.9| 29.8| 29.6| 29.8| 35.8| 41.7
B5:
SNR: 36 dB
H= 37 dB
M= 34 dB
L= 29 dB
APVf=MF-SF9 (dB)
Models
IT-15 FREE Aware
IT-16 FREE Aware EN 352
Important
Please read, understand, and follow all safety information. This product is
designed to protect against harmful noise.
Please note, only IT-16 is EN 352 Certified.
Fitting
ISOtunes® FREE Aware comes with a pair of One-Size-Fits-All
TRILOGY™ Triple Flange eartips and 6 sets of foam eartips tall and short
(S,M,L). Choose the size that fits the most snug in your ear canal. Remember,
the snugger the fit, the better the noise reduction.
ISOtunes® TRILOGYTM foam eartips have a threaded core, and the sound port of the earbud is also threaded.
- Carefully compress the foam eartip on the stem/sound port.
- Insert the eartip into your ear as deeply as comfortable
- Slightly rotate earbud until it is secure in the bowl of your ear.
- Make the earbud rest tightly next to your inner ear edge.
Hint: To open your ear canal wider, lift the top of your ear up and away
from your head, as shown in FIG 4.
Please Note: should the included Triple Flange eartips not fit your ears, all
ISOtunes® TRILOGYTM eartips fit this product. Eartips other than the ISOtunes®
TRILOGYTM silicone eartips size are not NRR/SNR rated for ISOtunes FREE Aware,
but should offer reasonable attenuation and performance.
Introduction
Thank you for purchasing ISOtunes® FREE Aware True Wireless Noise-Isolating
Earbuds. These earbuds have been specifically designed for use in noisy
environments allowing you to block out much of the surrounding noise so that
you can listen to your music or talk on the phone with less interruption.
Power ON/OFF
Method 1
Power ON: Open charging case
Power OFF: Place earbuds into charging case and close the lid.
Method 2
Power ON: In OFF mode, press and hold MFB for 3 seconds.
Power OFF: In ON mode, press and hold MFB for 3 seconds.
Bluetooth Pairing
After powering on, the earbuds will automatically enter Bluetooth Pairing
Mode. Look for quick red and blue flashes from the earbud as a confirmation.
Open the Bluetooth settings on your device. Search for “ISOtunes FREE Aware”.
Pair and connect. You will hear “Bluetooth Connected” once connected.
Charging
There are three batteries to charge:
- Charging Case Battery
- Left Earbud Battery
- Right Earbud Battery
Charging the Case
Insert USB type C charging cable to charge the case. The charging case battery
indicator light will start flashing to indicate charge level
Charging the Earbuds
Place earbuds into the charging case. The earbuds’ red indicator light
should be solid red, indicating that the earbuds are charging.
Only charge your ISOtunes FREE Aware with a Maximum 5 Volt charger. Using a charger higher than 5 Volts could be dangerous and may damage your ISOtunes product. Be especially careful with “quick charge” or “turbo charge” chargers, which often supply 9, 12, or 15 Volts. Your ISOtunes FREE Aware cannot be charged at voltage levels above 5 volts.
Battery Capacity
ISOtunes® FREE Aware supports Bluetooth® battery level indicator. This means
that when connected to iOS devices, the battery power status can be seen in
the upper right corner of the screen. Please use this as guideline – there are
many factors to battery level accuracy that influence this measurement. (For
example – although the battery power status may show 30% battery power
remaining, this may actually only be 5-10% on your ISOtunes®.)
Noise Attenuation
This product has been tested to the European Safety Standard
EN352-2:2020 and the ANSI S3.19-1974 standard for a hearing protector, with a Single Number Rating (SNR) of 32 dB and a Noise Reduction Rating (NRR) of 25 dB. Full testing details are available in the Noise Attenuation section of this booklet.
ANSI S3.19-1974
The level of noise entering a person’s ear, when ISOtunes® FREE Aware
headphones are worn as directed, is closely approximated by the difference
between the A-weighted environmental noise level and the Noise Reduction
Rating (NRR). Improper fit of this device will reduce its effectiveness in
attenuating noise. Consult the enclosed instructions for proper fitting.
A1: Frequency (Hz)
A2: Mean Attenuation (dB)
A3: Standard Deviation (dB)
Example:
- The surrounding noise level measured at the ear is 100 dB.
- The NRR of ISOtunes® FREE Aware is 26 dB.
- The noise level entering the ear is approximately equal to 74dB.
Please note that the NRR is based on the attenuation of continuous noise and may not be an accurate indicator of the protection attainable against impulsive noise, such as gunfire.
EN 352
B1: Frequency (Hz)
B2: Mean Attenuation (dB)
B3: Standard Deviation (dB)
B4: Assumed Protection Value (APV) (dB)
B5:
H = Hearing protection estimation for high frequency sounds (f 2000Hz)
M = Hearing protection estimation for medium frequency sounds (500 Hz < f <
2000Hz)
L = Hearing protection estimation for low frequency sounds (f 500Hz)
The EU declaration of conformity for IT-16 can be accessed at www.isotunes.co.uk/EU-declaration-of-conformity
The products will be certified to the Product standard EN 3522:2002 and the PPE Regulation 2016/425
SafeMax™ Technology
ISOtunes® FREE Aware incorporates SafeMax™ Technology, therefore its volume
output has been limited to 85 decibels (IT15), or 79 decibels (IT-16) .
ISOtunes® devices with SafeMax™ Technology are OSHA, and ANSI compliant.
Cleaning and Maintenance
- Clean your ISOtunes FREE Aware by gently wiping them with a clean, damp cloth with mild soap.
- Do not immerse the earbuds in water.
- Do not use abrasive cleaning solvents to clean the earbuds.
If the earbuds get wet from sweat or rain, please discontinue use and allow
them to dry.
Trilogy foam eartips are disposable. To ensure peak performance, we recommend
replacing TRILOGYTM Foam Tips every three months or when they become soiled.
In order to purchase additional tips, please go to
www.ISOtunes.com or
www.ISOtunes.co.uk
Clean your ISOtunes® FREE Aware by gently wiping them with a clean damp cloth.
Mild soap can be applied to the cloth.
Do not use abrasive cleaning solvents to clean the headset. Avoid scratching
the headset with sharp objects, as this may cause damage. Keep the headset
away from high temperature areas.
The TRILOGYTM foam eartips should be regularly inspected for deterioration,
cracking, or other damage. The eartips can be cleaned in between uses with a
damp cloth and water. Overtime, the eartips should be replaced.
WARNINGS
ISOtunes® FREE Aware does an excellent job of blocking outside noise. As such,
ISOtunes® FREE Aware should NOT be used in environments where users need to be
fully aware of their surroundings for personal safety reasons. For example, do
NOT use them while driving a car or riding a motorcycle. Similarly, do NOT use
them when riding a bicycle outside. The user is solely responsible for
ensuring that ISOtunes® FREE Aware is used ONLY in safe environments.
This product may be adversely affected by certain chemical substances. Further
information may be sought from the manufacturer.
These earplugs should not be used in situations where there is a risk that the
connecting cord could be caught up during use.
Recommendations
The wearer should ensure that the product is properly cleaned and dry before
and after use. Storage should be in a clean and dry location between -20 °C
and 50 °C.
The battery should not be fully discharged before long term storage.
The wearer should ensure that:
- The hearing protector is fitted, adjusted, and maintained in accordance with the manufacturer’s instructions.
- The hearing protector is worn at all times in noisy surroundings.
- The hearing protector is regularly inspected for serviceability.
If these recommendations are not adhered to, the protection afforded by the hearing protector maybe severely impaired.
Additional Notes
ISOtunes® FREE Aware is compliant with Bluetooth® V5. We do not guarantee
compatibility of all functions on every Bluetooth®enabled device. Please check
your device’s user manual for compatibility and functionality.
For additional information or questions about ISOtunes® products or spares and
accessories, please contact our support team. Weight: 15g (both earbuds), 50g
(case) Date of Obsolescence: 3 years from purchase date Not to be used in
Explosive Atmospheres
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning statement: The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
UK & Europe
[email protected]
North America
[email protected]
1-844-396-3737
Monday-Friday 9-5 ET
EU Importeur
Haven Technologies UK LTD
Winterhuder Weg 29 22075 Hamburg
Germany
References
- Product Manuals
- ISOtunes Product Manuals | Download User Manuals – ISOtunes®
- ISOtunes Product Manuals | Download User Manuals – ISOtunes®
- ISOtunes.com
- Product Manuals