WELLFOR EX3BMBL LED Bathroom Mirror Instruction Manual

See Better with Smart Light
EX3BMBL LED Bathroom Mirror
Instruction Manual

EX3BMBL LED Bathroom Mirror

WARNING AND SAFETY INSTRUCTIONS
Before assembling your LED Lighted Mirror fixture, please make sure that you carefully read through this instruction sheet, refer back to them during installation to ensure your product is fitted safely and correctly. Keep these instructions for future use.
WARNING Risk of Fire and ElectricShock

• All fittings must be installed in accordance with current IEE wiring regulations. If in doubt, consult a qualified electrician.
• Switch off the electrical supply at the main circuit board BEFORE installation and maintenance.
• Suitable for indoor use only. This product should be positioned well awayfrom curtains and fabrics. Never cover the mirror.
• Regularly check the cord, the transformer and all other parts for damage. If any part is damaged the product should not be used.

INSTALLATION SAFETY

• Inspect the product immediately upon receipt for the transit damage or missing parts. Handle the product with care and protect against knocks to all sides and
  edges of the glass.

• Ensure there are no hidden pipes or cables in the wall before drilling.

• Wear suitable eye protection when drilling. Take care if drilling ontiled surfaces in case the drill slips.

CAUTION
The light source of this product is non-changeable light diodes (LED). Do not disassemble the product, as the light diodes can cause damage to the eyes.
NOTE: The important safeguards and instructions that appear in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and care, are factors that can’t be built into any product. These factors must be supplied by the person(s) caring for and operating
the fixture. Do not install this fixture in hazardouslocations.
CHECK PRODUCT LIST AFTER OPENING THE PACKAGE

TOOLS YOU MAY NEED

1. Level and mark the location.

2. Place the mounting bar against the wall and make some marks on the wall.

3. Drill the holes and place the suitable plastic anchors.

4. Screw the mounting bar onto the wall with the screws.

5. Connect the mirror with the main supply.
   • We provide plug with mirrors.
   • Optional to cut the plug directly,then connect to electrical wiring if using wall switch.
   ATTENTION: PLEASE CUT OFF THE MAIN POWER SUPPLY BEFORE WIRING!

6. Hang the mirror onto the mounting bar.

OPERATION INSTRUCTION

ON/OFF and CCT adjustment

• Button turns blue when connected to main supply.
• Button always on as long as connecting to main supply.
• Short-touch the button to turn on/off the mirror.
• Adjusting color temperatures (CCT) between warm white and cool white by long-touching the button for seconds.
• Finish setting by withdrawing your finger when the color reaches the one you need.
• Optional to be wired to wall switch by ON/OFF memory function.

ON/OFF and Dimmer
**** Press and hold on for 3-5 seconds

• Short-touch the button to turn on/off the mirror.
• Long touching the button to adjust the brightness (Dimming).

Anti-Fog Function

Defoggerbutton

• Mirror begins to be warm and defog after pressing the defogger button. Press again to quit the anti-fog function.
• Note: The defogger will stop automatically after60 minutes of continuous operation to prevent any damage caused by prolonged high temperature.

Clock/Temperature

• Turn off the light to set the clock.

• Long touch button lor 2 for seconds,the Hour will flash, then short-touch buttonl and 2 to set Hour.

• Wait for seconds after setting up the Hour, then it will automatically switch to the Minute flash.

• Short-touch button land 2 to set up the Minute.

• Wait seconds after you finish the time setting,the time will be saved automatically

• The clock shows for Ss, and shift to the temperature showing for 2s, then go back to show the clock.

• It automatically displays the indoor temperature by auto sensing through the temperature sensor.

• DO NOT cover the temperature sensor.
  Night light

• Night light will be auto-on/off according to the brightness surrounding when the rocker switch is keeping turned on.

• If need turn off the nightlight at night, please turn off the rocker switch manually.

AFTERCARE INSTRUCTIONS
Clean using a soft dry cloth only when turned off. Never use cleaning agents or abrasive materials. Do not allow moisture to come into contact with lamp.
THANK YOU FOR YOURSUPPORT.
We wish you have wonderful experience in our product. If you have any other needs or queries, please feel free to contact us by email info@exbriteusa.com, and get replies within 48 business hours.

For customer support please call 206.809.0093 weekdays 9:00 to 6:00 PST, or by
email:service@wellfor.com.
For more information:www.wellfor.co

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>