TroposAir 88652 72-in Oil Rubbed Bronze Indoor/Outdoor Propeller Ceiling Fan Instruction Manual
- June 9, 2024
- TroposAir
Table of Contents
TroposAir 88652 72-in Oil Rubbed Bronze Indoor/Outdoor Propeller Ceiling Fan
READ AND SAVE THESE INSTRUCTIONS
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, PLEASE OBSERVE THE FOLLOWING:
-
To ensure success of installation, be sure read these instructions and review the diagrams thoroughly before beginning.
-
To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
All electrical connections must be made in accordance with local codes, ordinances and/or the National Electrical Code. If you are unfamiliar with the methods of installing electrical wiring and products, secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections. -
Make sure that your installation site will not allow rotating fan blades to come into contact with any object. Blades should be at least 7 feet from the floor when fan is in operation
-
If possible, mount ceiling fan on a ceiling joist – the joist must be able to support the motion and weight of the moving fan. If the fan will be mounted on a ceiling outlet box, a 4″ x 2 1/8″ deep METAL octagon box is required; one UL listed as “suitable for fan support”. The box and its supporting members must not be able to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should be performed by qualified personnel.
-
Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in carton until ready to be installed to protect its finish.
If you are installing more than one ceiling fan, make sure that you do not mix fan blade sets. -
After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet 6ox and the “HOT” wires on the other sacbe.
-
Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UUETL listed and should be installed per the light kit’s installation instructions.
-
After fan is completely installed, check to make sure that all connections are secure to prevent fan from falling and/or causing damage or injury.
-
The fan can be made to work immediately after installation. The bearings are adequately charged with grease, so that, under normal conditions, further lubrication should not be necessary.
-
The fan turns off and stops before reversing fan direction.
-
This fan is suitable for sloped ceiling.
-
This fan is electrically reversible.
-
This fan can be outfitted with an integrated light kit.
-
This fan is controlled by remote control.
-
This fan is suitable for indoor use or damp location use.
Unpack and inspect fan carefully to be certain all contents are included
WARNING: blades should be at least 7 feet from floor
Note 1:
Turn off power at breaker box to avoid possible electrical shock.
Note 2:
Use metal outlet box suitable for fan support. Outlet box must support 35 lbs
min.
HANGING SYSTEM INSTALLATION
A. Installing mounting bracket to ceiling outlet box
Install mounting bracket to outlet box in ceiling by using screws included
with the outlet box and washers from the hardware bag.
BLADE INSTALLATION
Installing the blades onto blade plate
① Lay the blade plate on a flat surface with the “This Side Up” facing UP,-
Place the blade also with the “This Side Up’ facing up.
② Align five holes in blade with the five on the blade plate and secure with
blade screws and washers. Repeat for remaining blades.
③ Carefully fillip. the blade assembly over so that the ‘This Side Up” is down
and balance it on the motor face.
④ Align the eight holes in the blade plate to the eight in the motor face and
secure with tne eight Plate Screws.
If installing the #650 LED Array do it while motor is u side down.
Secure light pan to the light hub using 3 light pan screws.
Secure LED array to light pan with 3 array screws, and plug it in.
Secure clear lens to the light pan using 3 lens screws.
HANGING SYSTEM INSTALLATION
3A. Repositioning the Motor
Gently flip motor-blade assembly over and place motor right side up onto
styrofoam packing.
3B. Installing Downrod and Yoke
① Remove cross pin, washer and cotter pin from downrod.
② Insert downrod through canopy and yoke cover, and feed motor wires through
downrod.
③ Loosen 2 downrod jam screws at yoke. Insert downrod assembly into yoke.
④ Insert the cross pin through yoke & downrod and secure with washer and
cotter pin.
⑤ Tighten both downrod jam screws to further secure downrod.
3C. Hanging the fan
Lift fan assembly onto the mounting bracket.
Rotate the fan so that the groove on the ball engages the ridge on the
mounting bracket.
WIRING CONNECTION
4A. Insert receiver into mounting bracket
Note: Do not squeeze all the wires while inserting the receiver into the
mounting bracket.
4B. Making electrical wire connections
Detailed instructions are enclosed with the remote.
For convenience basic wiring connections are shown here
CANOPY INSTALLATION
Installing the canopy
Note: Two screws are pre-installed on mounting bracket for canopy
installation. You will need to remove one and loosen the other slightly.
① Push up canopy until the screw still in the mounting bracket is engaged with
the large end of the keyhole on canopy.
② Rotate canopy slightly until the screw head is engaged in the narrow end of
the key hole.
③ Insert the remaining canopy screw into the other hole, and tighten both
canopy screws.
COVER INSTALLATION
**Non-Lighted Installation ...**
Installing the Cover
① Lift the cover up to the motor aligning the threaded opening to the threaded
hub
② Thread the cover clockwise until secure.
**If you have installed the #650 Light ...**
Installing the Light Cover
① Lift light cover to motor aligning the opening of the grooves to the nibs
inside the light pan
② Rotate cover 1 /4 turn clockwise to secure it to motor assembly.
REMOTE SETTING
Setting the Remote Control
Follow the separate instructions enclosed with the remote control.
This fan model has an optional integrated dimmable LED array;
Use the “D” dimming setting for the Light Function Select Switch.
For convenience the initial setup is summarized here. Install Batteries, ID the LEARN button, Turn on power, within 30 seconds press LEARN for approx 2 seconds. Bi-Bi = Done.
**INSTALLATION IS COMPLETE**
Documents / Resources
|
TroposAir 88652 72-in Oil Rubbed Bronze Indoor/Outdoor Propeller Ceiling
Fan
[pdf] Instruction Manual
88652 72-in Oil Rubbed Bronze Indoor Outdoor Propeller Ceiling Fan, 88652,
72-in Oil Rubbed Bronze Indoor Outdoor Propeller Ceiling Fan, Indoor Outdoor
Propeller Ceiling Fan, Propeller Ceiling Fan
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>