TroposAir IM-3MX60 Astra WiFi Ceiling Fan Owner’s Manual

Astra WiFi
(3MX60)

Owners Manual

Toll Free: 1-855-676-724 7
Net weight

IM-3MX60 Astra WiFi Ceiling Fan

WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.

READ AND SAVE THESE INSTRUCTIONS$

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, PLEASE OBSERVE THE FOLLOWING:

1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning.

2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
   All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.
   If you are unfamiliar with the methods of installing electrical wiring and products, require the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper  installations and connections.

3. Make sure that your installation site will not allow rotating fan blades to come in contact with any object when fan is in operation. Blades must mounted at least 7 feet from the floor.

4. If possible, mount ceiling fan on a ceiling joist – the joist must be able to support the motion and weight of the moving fan.
   If the fan will be mounted on a ceiling outlet box, a 4″ x 2-1/8″ deep METAL octagon box is required ; one UL listed as ” suitable for fan support “. The box and its supporting members must not be able to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should be performed by qualified personnel.

5. Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in carton until ready to be installed to protect its finish.
   If you are installing more than one ceiling fan, make sure that you do not mix fan blade sets.

6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be spread apart with the grounded conductor and the equipment – grounding conductor on one side of the outlet  box and the “HOT” wires on the opposite side.

7. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed and should be installed per the light kit’s installation instructions.

8. After fan is completely installed, check to make sure that all connections are secured to prevent fan from falling and/or causing damage or injury.

9. The fan can be made to work immediately after installation. There is no need to oil your fan.
   The motor has permanently lubricated bearings.

10. The fan must be turned off and stopped before reversing fan direction.

11. The fan is for down rod mount only.

12. This fan is reversible.

13. This fan is controlled by remote.

14. This fan is suitable for damp location use.

Unpack and inspect fan carefully to be certain all contents are included.

Unpack (Fan & Blades packed in one Box)

Hardware Bag

For Mounting Bracket:

Flat Washer x2
Spring Washer x2
Machine Screw x2
Wood Screw x2|
---|---

For Blade Installation
Flat Washer x 13 (one spare washer included)

Blade Screw x 13 (one spare screw included)

For Wire Connection:

Wire Nut x 6|
---|---

For Blade Balance:

Balanced Slide x 1
Weight Block (5G x 3)|
---|---

Remote Control

Hardware Bag

WARNING: BLADES SHOULD BE AT LEAST 7 FEET FROM FLOOR

Note 1:
Turn off power at breaker box to avoid possible electrical shock

Note 2:
Use metal outlet box suitable for fan support.
Outlet box must support 35lbs min.

HANGING SYSTEM INSTALLATION

Installing mounting bracket to ceiling outlet box

1.1 lnstall mounting bracket to outlet box on ceiling by using screws included with the outlet box and washers from the hardware bag.

1-2 Loosen the screws at mounting bracket Do not remove.

BLADE INSTALLATION

Use Styrofoam as cushion for this step.
place the fan assembly on Styrofoam with yoke up

Attach blades to fan assembly by using screws(2) & spring washer(2) provided from hardware bag of fan assembly.
(Repeat until all 3 blades are installed firmly.)

*Turning the fan assembly upside (cap side up)

Attach screws(2) on bottom of fan assembly provided from hardware bag.

*Note: Make sure all blade washer & screws are tightened to avoid operating noise.

DOWN ROD INSTALLATION

3-1. Remove cross pin and cotter pin from downrod
3-2. Loosen 2downrod jam screws at yoke

3-3. As shown above, insert yoke cover, deco ring, canopy onto downrod.

3-4. Insert the lead wires through the downrod assembly.

3-5.Insert downrod assembly into yoke and attach the cross pin through yoke & downrod, secure with cotter pin.

3-6. Make sure the position of the Hex nut must be on side of jam screw head, before tighten jam screw.
3-7. Tighten 2 jam screws to secure downrod

3-8. Use spanner to tighten the Hex nut, so the jam screw will not loosen.
3-9. Pull down the yoke cover to cover yoke.

HANGING THE FAN ONTO MOUNTING BRACKET

4-1. Liftfan assembly onto mounting bracket.

4-2. Rotate fan so that the groove on the ball engages the ridge in the mounting bracket.

WIRE CONNECTION

5-1. Verify that serial Number & Model Number match on the Receiver and Transmitter
NOTICE
Many remote sets for DC fens look the same This remote setis pre-paired and labeled at the factory, please note the following before operation:
1a. The Remote Model Number on transmitter and receiver must be the same.
1b.The Remote Serial Number will be the same ona pre-paired remote set. If it is different, it will need to be paired (See page 11)
2.The Fan Model Number label fut be the same as the fan’s model number in front page (3MX60) for proper operation(There is no fan Model Number on transmitter )
3.Do not mix the remote sets if you are installing more than one fan.

5-2. Insert receiver into mounting bracket
NOTE:  Do not squeeze all the wires while inserting the receiver into the mounting bracket.

5-3. Making electrical wire connection

The standard lead wire is 54 long.
You may need to cut all5lead wires (from motor) to proper length& strip them for wire connection to make it easier for Canopy installation.

Follow diagram below and make sure that all exposed wires are secured inside wire nuts.
Note: Wires from house may vary in color. If the house wires do NOT include a ground/earth wire (bare or green), it will not affect operation of the fan, but an electrician can be consulted to provide this safety feature.
After wiring is completed, gently push wires into junction box with wire nuts pointing upward.

CANOPY INSTALLATION

Note: Two screws are installed on mounting bracket for canopy installation.
6-1. Push up canopy until two pre-installed screws on mounting bracket are engaged with two key holes on canopy.
6-2. Rotate canopy slightly until two pre-installed screws heads are engaged in the narrow end of key holes.
6-3.Tighten both screws.

6-4. Push deco ring up to canopy, align holes on canopy with nibs on deco ring, and push to snap in.

MOTOR CAP INSTALLATION

Attach the Motor Cap by screwing it clockwise onto the Motor.

TRANSMITTER INSTALLATION

The enclosed Transmitter can be mounted in many ways:

1. On-Wall at any convenient location, see Section (2) next page.
2. In-Wall in US switch boxes {multi-gang and single-gang decora), see Section (3).
3. Either way can be still used as a Hand-Held transmitter, or
4. It can be Permanently Stationed either On-Wall or In-Wall, see Section (4).

HAND-HELD ASSEMBLY
1-1. Open the front cover of Hand- Held.

1-2. Install the 12V battery. (provided)

1-3. Reinstall the front cover and secure into place using the small self­ tapping screw from the hardware bag.

A. On-Wall Mount

ON-WALL BRACKET INSTALLATION
2-1. Position the bracket on the wall where desired, with the single post at the bottom as shown, secure the bracket with the two Wood Screws provided.
(Wall anchors are for concrete wall.)

2-2. Snap the Hand-Held onto the On-Wall Bracket by aligning 3 posts to three recessed holes in back of Hand-Held.

IMPORTANT: Single post of wall bracket must be downward.

You have completed the Wall mount installation.

B. Decora In-Wall Installation {for U.S.A.)

DECORA IN-WALL INSTALLATION (USA)
Warning: Turn off power at breaker box to avoid possible electric shock.

3-1. Remove the wall plate by loosening screws from the wall plate. (Keep these screws for step 3-6.)
Note: Can be installed in single- or multiple-gang switch box.

3-2. Uninstall the wall switch from the switch box by removing two screws from the switch box. (Keep these screws for step 3-5.)

Warning: Make sure the power is turned off at the breaker box before touching anything in this box.
Caution: If you are uncomfortable identifying and connecting 120V AC wiring connections, we recommend you hire a licensed electrician to perform this installation.

Caution: The following wiring instructions are valid for a simple on/off toggle switch in a single gang box.
Caution: If your switch has more than two wires (not counting any ground wire or jumpers), we recommend hiring a licensed electrician to identify and complete the wiring connections.

3-3. Remove the wall switch from the switch box, and disconnect the following wires from the wall switch:

1. Remove Black wire that goes to ceiling junction box
2. Remove Black wire(s) that comes from AC source

3-4. Connect the Black wire that goes to the ceiling box to the Black wire(s) from the AC source using the wire nuts provided.

Note: Ground wires are usually twisted together in the box and do not require wire nut. If your ground wires are separated, connect them with a provided wire nut.
Note: The White wires (neutral) should remain tucked in the back of the box.
Note: Make sure that all exposed wires are secured inside wire nuts.
Carefully tuck wires neatly back into switch box.

IMPORTANT: FAN’S REMOTE RECEIVER IS NOW DIRECTLY CONNECTED TO AC POWER. ON/OFF IS NOW OPERATED BY REMOTE TRANSMITTER.

3-5. Install the Decora In-Wall bracket onto the switch box with the single post at the bottom as shown, and attach two screws removed from step 3-2.
(If in a multiple-gang box align the bracket using the wall plate first, then tighten the screws.)

3-6. Install the wall plate onto the switch box and attach the screws removed from step 3-1.

3-7. Snap the Hand-Held onto the In-Wall Bracket by aligning 3 posts to three recessed holes in back of Hand-Held.

You have completed the In-Wall Mount installation.
The next section (4) details how to make it a Permanently Stationed control.

FOR PERMANENTLY STATIONED CONTROL
(For school, hotel or public facility so the hand-held cannot be easily removed.)

4-1. Open battery cover of Hand-Held by removing the self-tapping screw.

4-2. Using the proper screw for the bracket used, attach the Hand-Held to the bottom post of the bracket through the screw compartment hole.
A. On-Wall Bracket: Use provided self-tapping screw.
B. In-Wall Decora: Use provided machine screw.

A. On-Wall Bracket

B. In-Wall Decora

4-3. Snap the cover back onto the transmitter and secure with small self- tapping screw removed in step 4-1.

Turn on the power at breaker box, the fan is ready for operation!

OPERATIONAL INSTRUCTION

Warning: DO NOT PRESS THE BUTTON FOR MORE THAN 4 SECONDS TO AVOID FACTORY RESET AND THE LOSS OF PRE.PAIRED PROGRAMING OF RECEIVER AND TRANSMITTERE!

All the button pressed will have a Beep sound and the red indicator light will turn on.

| 9-1. Indicator
9-2. Press0 button to turn the fan ON/OFF
Note: On every startup, the fan will move forward&backward for2-3seconds.
9-3.Reverse switch
9-4. WiFioairing
(long press for5seconds, see more information for WiFisetting in step 11.)
9-5. AP mode.
(long press for5seconds, see more information for WiFisetting in step 11.)
9-6. Fan Speed:
1-LowSpeed → 5-High Speed.
9-7 .12v battery (23AE/A23) included, install in front.
---|---

Note: Press button to turn the fan ON/OFF, The remote retains the last settings (fan speed and direction) in memory, If the fan is unintentionally turned OFF and ON again at the main power or during a power failure, the fan will be Orr and previous settings  will be lost.

TROUBLESHOOTING

In the event the fan does not operate properly, please perform the following steps.

1. Lower the canopy and check that all wires are connected properly.
2. Perform the remote Pairing Process at step 10-1 on P11.

REMOTE PAIRING PROCESS

The Pairing Process is only necessary when there is an issue. Remote set is pre-paired from the factory and should not require the Pairing Process.

A fan may need to have “Pairing Process” performed for the following issues.

1. Replacing the transmitter.
2. Replacing the receiver.
3. Multiple fans on the same circuit.
   (In multiple fans situation, each fan must be wired up individually for the Pairing Process; see step 10-1.)

10-1. Pairing Process for transmitter and receiver:

1. Switch off the main power and make sure fan has completely stopped.
2. Install a New receiver or install the battery in a new transmitter before the Pairing Process.
3. Switch on the power again, and immediately:

This fan has completed the pairing successfully and the fan is ready for operation!

10-2A. Pairing Process for Multiple fans (One transmitter for multiple receivers)
If you wish to use only one transmitter for two fans, simply wire up both fans at one time and perform the Pairing Process at step 10-1 from a point between the two fans.

10-2B. Pairing Process for Multiple fans (One transmitter for one receiver)
The Pairing Process must be performed on each remote set (transmitter and receiver) individually.
See the set up at step 10-3.

10-3. TO SET UP REMOTE FOR #1 FAN

Make sure to turn off power at breaker box.
Disconnecting wire from #2 fan.
Before starting the remote control setting process, lower the canopy of #2 Fan and disconnect the Black wire.
Put the wire nut on the black wire from the house

Turn on power at breaker box and #1 Fan is ready for pairing.
*See the remote control setting process 10-1 to set up #1 Fan.

10-4. TO SET UP REMOTE FOR #2 FAN

Make sure to turn off power at breaker box.

Disconnecting wire from #1 Fan
Disconnect the Black wires from #1 Fans and connect the Black wires back to #2 Fan that you remove from 10-3.

Turn on power at breaker box and #2 Fan is ready for setting.
*See the remote control setting process for 10-1 to set up #2 Fan.

10-5. RECONNECT ALL FANS

Make sure to turn off power at breaker box.
After all the fans have done the resetting process, reconnect all the wires for #1 fan & #2 fan, and lift up the Canopy of #1 fan & #2 fan.

10-6. Switch on the main power and now each of these two fans are operated by its own remote individually.

NOTE: For more than two fans, the same rules apply. Make sure only one fan at a time is connected to power when doing the Remote Setting. Already completed fans should be disconnected until all fans have completed the Remote Setting process.

WIFI PAIRING

A. Installation
You can scan the QR code below to download the Smart Life app.
You can also search Smart Life” in major application markets to install the app.

B. Register an account and log in.

C. WiFiConnect

NOTE: You must turn on the “Location Services” before Wifi pairing.

1. First ensure that Wiican be used normally an you have the pas8w0rd

2. Click Add Device”, fest select “Small Home Appliance”,then select Fan (Wi-Fi).
   

3. Press and hold the button of the transmitter for more than S seconds.Wait until the ceiling fan receiver emits “Bee8lee” continuously. The remote makes this noise instead of a blinking indicator as described in the app.

4. Select the correct Wifi source, then enter the WiFi password and click “Confirm”,click confirm the indicator is blinking” then select Blink Quickly and wait white Connecting”.
   

5. Wait for a successful connection.
   

NOTE: In case of above WiFi Pairing failed, please follow below and pairing. (AP Mode)

1. Press and hold pa “ “tutton of the transmitter for more than S seconds. Wait until the ceiling fan receiver snits BeeBee” continuously.

2. Click “Confirm the indicator is blinking” and select “Blink Slowly” to enter AP Mode.
   

3. Select the device’s hotspot then wait while Connecting”.

4. Wait for a successful connection.

D. More Details and Multiple Users

1. ln the App’s Main Control Panel, click the “ “in the upper right corner for more functions.
   a. Tap on the icon or name to change either.
   b. Tap Share Device” “Add Sharing”.
   

2. Enter the phone number of another Smart Life user, and click Completed” to share.
   Hint: The simplest way to share multiple devices with multiple users is to log in as a public account.
   NOTE:This method requires the other users have the Smart Life” app installed.

E. For more information, go to the Me”.FAQ & Feedbacke” in the app to learn.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>