TUNTURI Star Fit E100 Exercise Bike User Manual
- June 9, 2024
- Tunturi
Table of Contents
TUNTURI Star Fit E100 Exercise Bike
Instruction
Upright Bike
Welcome to the world of Tunturi New Fitness!
Thank you for purchasing this piece of Tunturi equipment. Tunturi offers a
wide range of home fitness equipment, including crosstrainers, treadmills,
exercise bikes and rowers. The Tunturi equipment is suitable for the entire
family, no matter what fitness level. For more information, please visit our
website
www.tunturi.com
Safety warnings
WARNING
- Read the safety warnings and the instructions. Failure to follow the safety warnings and the instructions can cause personal injury or damage to the equipment. Keep the safety warnings and the instructions for future reference.
- The equipment is suitable for domestic use only. The equipment is not suitable for commercial use. Max. usage is limited to 3 hrs a day.
- The use of this equipment by children or persons with a physical, sensory, mental or motorial disability, or lack of experience and knowledge can give cause to hazards. Persons responsible for their safety must give explicit instructions or supervise the use of the equipment.
- Before starting your workout, consult a physician to check your health.
- If you experience nausea, dizziness or other abnormal symptoms, immediately stop your workout and consult a physician.
- To avoid muscular pain and strain, start each workout by warming up and finish each workout by cooling down. Remember to stretch at the end of the workout.
- The equipment is suitable for indoor use only. The equipment is not suitable for outdoor use.
- Only use the equipment in environments with adequate ventilation. Do not use the equipment in draughty environments in order not to catch a cold.
- Only use the equipment in environments with ambient temperatures between 10 °C and 35 °C. Only store the equipment in environments with ambient temperatures between 5 °C and 45 °C.
- Do not use or store the equipment in humid surroundings. The air humidity must never be more than 80%.
- Only use the equipment for its intended purpose. Do not use the equipment for other purposes than described in the manual.
- Do not use the equipment if any part is damaged or defective. If a part is damaged or defective, contact your dealer.
- Keep your hands, feet and other body parts away from the moving parts.
- Keep your hair away from the moving parts.
- Wear appropriate clothing and shoes.
- Keep clothing, jewellery and other objects away from the moving parts.
- Make sure that only one person uses the equipment at a time. The equipment must not be used by persons weighing more than 120 kg (265 lbs).
- Do not open equipment without consulting your dealer.
Electrical safety
(Only for equipment with electric power)
-
Before use, always check that the mains voltage is the same as the voltage on the rating plate of the equipment.
-
Do not use an extension cable.
-
Keep the mains cable away from heat, oil and sharp edges.
-
Do not alter or modify the mains cable or the mains plug.
-
Do not use the equipment if the mains cable or the mains plug is damaged or defective. If the mains cable or the mains plug is damaged or defective, contact your dealer.
-
Always fully unwind the mains cable.
-
Do not run the mains cable underneath the equipment. Do not run the mains cable underneath a carpet. Do not place any objects on the mains cable.
-
Make sure that the mains cable does not hang over the edge of a table.
Make sure that the mains cable cannot be caught accidentally or tripped over. -
Do not leave the equipment unattended when the mains plug is inserted into the wall socket.
-
Do not pull the mains cable to remove the mains plug from the wall socket.
-
Remove the mains plug from the wall socket when the equipment is not in use, before assembly or disassembly and before cleaning and maintenance.
Description (fig. A)
Your upright bike is a piece of stationary fitness equipment used to simulate cycling without causing excessive pressure to the joints.
Package contents (fig. B & C)
- The package contains the parts as shown in fig. B.
- The package contains the fasteners as shown in fig.
C. Refer to the section “Description”
NOTE
If a part is missing, contact your dealer.
**Assembly (fig. D)
**
WARNING
- Assemble the equipment in the given order.
- Carry and move the equipment with at least two persons.
CAUTION
- Place the equipment on a firm, level surface.
- Place the equipment on a protective base to prevent damage to the floor surface.
- Allow at least 100 cm of clearance around the equipment.
- Refer to the illustrations for the correct assembly of the equipment.
Workouts
The workout must be suitably light, but of long duration. Aerobic exercise is
based on improving
the body’s maximum oxygen uptake, which in turn improves endurance and
fitness. You should perspire, but you should not get out of breath during the
workout.
To reach and maintain a basic fitness level, exercise at least three times a
week, 30 minutes at a time. Increase the number of exercise sessions to
improve your fitness level. It is worthwhile to combine regular exercise with
a healthy diet. A person committed to dieting should exercise daily, at first
30 minutes or less at a time, gradually increasing the daily workout time to
one hour. Start your workout at low speed and low resistance to prevent the
cardiovascular system from being subjected to excessive strain.
As the fitness level improves, speed and resistance can be increased
gradually. The efficiency of your exercise can be measured by monitoring your
heart rate and your pulse rate.
Exercise Instructions
Using your fitness trainer will provide you with several benefits, it will
improve your physical fitness, tone muscle and in conjunction with a calorie
controlled diet help you lose weight.
The warming up phase
This stage helps get the blood flowing around the body and the muscles working
properly. It will also reduce the risk of cramp and muscle injury. It is
advisable to do a few stretching exercises as shown below. Each stretch should
be held for approximately 30 seconds, do not force or jerk your muscles into a
stretch – if it hurts, STOP
The exercise phase
This is the stage where you put the effort in. After regular use, the muscles
in your legs will become more flexible. Work to your but it is very important
to maintain a steady tempo throughout. The rate of work should be sufficient
to raise your heart beat into the target zone shown on the graph below.
HEART RATE
This stage should last for a minimum of 12 minutes though most people start at about 15-20 minutes
The cool down phase
This stage is to let your Cardiovascular System and muscles wind down. This is
a repeat of the warm
up exercise e.g. reduce your tempo, continue for approximately 5 minutes. The
stretching exercises should now be repeated, again remembering not to force or
jerk your muscles into the stretch.
As you get fitter you may need to train longer and harder. It is advisable to
train at least three times a week, and if possible space your workouts evenly
throughout the week.
Muscle toning
To tone muscle while on your fitness trainer you will need to have the
resistance set quite high. This will put more strain on our leg muscles and
may mean you cannot train for as long as you would like. If you are also
trying to improve your fitness you need to alter your training program. You
should train as normal during the warm up and cool down phases, but towards
the end of the exercise phase you should increase resistance making your legs
work harder. You will have to reduce your speed to keep your heart rate in the
target zone.
Weight loss
The important factor here is the amount of effort you put in. The harder and
longer you work the more calories you will burn. Effectively this is the same
as if you were training to improve your fitness, the difference is the goal.
Heart rate Pulse rate measurement (hand pulse sensor s)
The pulse rate is measured by sensors in the handlebars when the user is
touching both sensors at the same time. Accurate pulse measurement requires
that the skin is slightly moist and constantly touching the hand pulse
sensors. If the skin is too dry or too moist, the pulse rate measurement will
become less accurate.
NOTE
- Do not use the hand pulse sensors in combination with a heart rate chest belt.
- If you set a heart rate limit for your workout, an
Maximum heart rate (during training)
The maximum heart rate is the highest heart rate a person can safely achieve
through exercise stress. The following formula is used to calculate the
average maximum heart rate: 220 – AGE. The maximum heart rate varies from
person to person.
WARNING
Make sure that you do not exceed your maximum heart rate during your workout.
If you belong to a risk group, consult a physician.
Beginner 50-60% of maximum heart rate
Suitable for beginners, weight-watchers, convalescents and persons who have
not exercised for a long time. Exercise at least three times a week, 30
minutes at a time.
Advanced 60-70% of maximum heart rate
Suitable for persons who want to improve and maintain fitness. Exercise at
least three times a week, 30 minutes at a time.
Expert 70-80% of maximum heart rate
Suitable for the fittest of persons who are used to long-endurance workouts.
Use
Adjusting the support feet
The equipment is equipped with 4 support feet. If the equipment is not stable,
the support feet can be adjusted.
- Turn the support feet as required to put the equipment in a stable position.
- Tighten the lock-nuts to lock the support feet.
NOTE
The machine is the most stable when all support feet are turned fully in.
Therefore start to level the machine by turning all support feet fully in,
before turning out the required support feet to stable the machine. .
Adjusting the vertical seat position
The vertical seat position can be adjusted by setting the seat tube to the
required position. With the leg almost straight, the arch of the foot must
touch the pedal at its lowermost point.
- Loosen the seat tube adjustment knob.
- Move the seat tube to the required position.
- Tighten the seat tube adjustment knob.
Adjusting the horizontal seat position (fig. E-2)
The horizontal seat position can be adjusted by setting the seat to the
required position.
- Loosen the quick release lever under the seat.
- Slide the seat forward or backward as desired.
- Tighten the quick release lever.
Adjusting the handlebar
The handlebar can be adjusted according to the height and the exercise
position of the user.
- Loosen the handlebar adjustment knob.
- Move the handlebar to the required position.
- Tighten the handlebar adjustment knob.
Power supply (Fig. E-1)
The trainer is powered by an external power supply. Refer to the illustration
to locate the trainer power input.
NOTE
- Connect the power supply with the trainer before connecting it to the wall outlet.
- Always remove power cord when
- machine is not in use.
- Display
- Buttons
- Tablet/ book support
CAUTION
- Keep the console away from direct sunlight.
- Dry the surface of the console when it is covered with drops of sweat.
- Do not lean on the console.
- Only touch the display with the tip of your finger. Make sure that your nails or sharp objects do not touch the display.
NOTE
The console switches to standby mode when the equipment is not used for 4
minutes.
Explanation Display functions
Time
- Without setting the target value, time will count up.
- When setting the target value, time will count down from your target time to 0 and alarm will sound or flash.
- Range 0:00~99:59
Speed
-
Displays current training speed.
Maximum speed is 99.99 KM/H -
Without any signal being transmitted into the monitor for 3 seconds during workout, SPEED will display “0.0”
RPM
- Displays the Rotation Per Minute.
- Display range 0~20~999.
- Without any signal being transmitted into the monitor for 3 seconds during workout, RPM will display “0”
Distance
- Without setting the target value, distance will count up.
- When setting the target value, distance will count down from your target distance to 0 with an alarm sound or flash.
- Range 0.00~99.99
Odo
- Automatically accumulates the Total distance for all exercise sessions.
- Range: 0.0 ~ 99.99 KM/ 0.00 ~ 9999 KM.
Calories
- Without setting the target value, calorie will count up.
- When setting the target value, calories will count down from your target calorie to 0 with an alarm sound or flash.
- Range 0~999.9.
- NOTE This data is a rough guide for comparison of different exercise sessions which cannot be used in medical treatment
Watt
- Display current workout watts.
- Range: 0.0 ~ 999.9 Watt.
Target HR
- Display user Target Heart rate (in workout mode only)
- Based on 70% of max. HR (220-Age)
Age
- Display user age (in programming mode only)
- Range: 10 ~ 99
Pulse
- Current pulse will display after 6 seconds when detected by the console.
- Without any pulse signal for 6 seconds, console will display “P”.
- Pulse alarm will sound when current pulse is over the target pulse.
- Range 0-60 ~ 220 BPM.
Level
- Shows tension level setting.
- Range: 1 ~ 24
Program
- Show current selected workout mode. (1 ~ 19) Explanation of buttons
Arrow up
- Increase resistance level in workout mode
- Setting selection in programming mode.
Arrow down
- Decrease resistance level in workout mode.
- Setting selection in programming mode.
Mode
- Press MODE button to switch between the parameters of the multi display windows. (in workout mode)
Enter
- Confirm setting or selection.
Start/ Stop
- Start or Stop workout.
- Push and hold ”Start/ Stop” button for 3 seconds to reset: Time, Speed, Distance, Calories, Pulse & Program.
Recovery
- After the console detects pulse signal, press the RECOVERY key to enter recovery mode to monitor heart rate recovery ability
Opperation
- Power on
- Plug in power supply to power on computer.
- Press any key to power on the console when being in sleep mode..
- Start pedalling to power on the console when being in sleep mode.
- Power off
Without any signal being transmitted into the monitor for 4 minutes the monitor will enter SLEEP mode automatically. (Active training data will be lost)
Programs
- Programs (fig. – F-01~F19)
- Quick start (Program 1)
- Press START/ STOP key to start your workout without any pre-set setting.
- Use UP/ DOWN to adjust resistant level during workout.
End your workout
-
Press START/ STOP in workout mode to stop/pause your workout.
To resume your workout press START/ STOP button in pause mode. -
Press and hold START/ STOP key for over 2 seconds to reset console. (Active training data will be lost)
Program mode (Program 1~9)
-
Use UP/ DOWN key to select Program 1 ~ 9 and press ENTER to confirm.
-
Use UP/ DOWN key to set TIME,
Range: 0:00 – 5:00 ~ 99:00 ±1:00 confirm setting by pressing ENTER. -
Use UP/ DOWN key to set DISTANCE,
Range: 00.00 – 00.10 ~ 99.90 ± 00.10 confirm setting by pressing ENTER. -
Use UP/ DOWN key to set CALORIES,
Range: 0.0 – 1.0 ~ 999.0 ± 1.0 confirm setting by pressing ENTER. -
Use UP/ DOWN key to set AGE,
Range: 10 ~ 99 ± 1 confirm setting by pressing ENTER
NOTE
- When setting more than one goal, the training will end at first achieved goal.
- Continue the workout by pressing START/ STOP button, and training will end again at first next achieved goal.
- Leave a goal blank and it will not be seen as a pre-set limit.
- Target HR is only for visual reference, pulse information will blink when value is over target.
- Press START/ STOP key to start workout
- Use UP/ DOWN key to adjust resistance level. Load level is shown in LEVEL window.
- Press START/STOP key to pause workout.
- Press and hold START/ STOP key for over 2 seconds to reset console and to go back to main menu. (Active training data will be lost)
Program mode (Program 10)
- Use UP/ DOWN key to select Program 10 and press ENTER to confirm.
- Use UP/ DOWN key to set TIME, Range: 0:00 – 5:00 ~ 99:00 ±1:00 confirm setting by pressing ENTER.
- Use UP/ DOWN key to set DISTANCE, Range: 00.00 – 00.10 ~ 99.90 ± 00.10 confirm setting by pressing ENTER.
- Use UP/ DOWN key to set CALORIES, Range: 0.0 – 1.0 ~ 999.0 ± 1.0 confirm setting by pressing ENTER.
- Use UP/ DOWN key to set WATT Range: 20 ~ 300 ± 10 confirm setting by pressing ENTER.
- Use UP/ DOWN key to set AGE, Range: 10 ~ 99 ± 1 confirm setting by pressing ENTER
NOTE
- When setting more than one goal, the training will end at first achieved goal.
- Continue the workout by pressing START/ STOP button, and training will end again at first next achieved goal.
- Leave a goal blank and it will not be seen as a pre-set limit.
- Press START/ STOP key to start workout
- Use UP/ DOWN key to adjust resistance level. Load level is shown in LEVEL window.
- Press START/STOP key to pause workout.
- Press and hold START/ STOP key for over 2 seconds to reset console and to go back to main menu. (Active training data will be lost)
Body Fat (Program 11)
-
Use UP/ DOWN key to select Program 11 and press ENTER to confirm.
-
Use UP/ DOWN key to set gender,
Range: Male / Female confirm setting by pressing ENTER. -
Use UP/ DOWN key to set Height,
Range: 110.0 ~ 199.5 cm ± 0.5 confirm setting by pressing ENTER. -
Use UP/ DOWN key to set Weight,
Range: 10.0 ~ 200.0 kg ± 0.2 confirm setting by pressing ENTER. -
Use UP/ DOWN key to set Age,
Range: 10 ~ 99 ± 1 confirm setting by pressing ENTER -
Press START/ STOP key to start Body fat measurement.
-
During measuring, users have to hold both hands on the Hr. hand grips. LCD display “- – – -” for 15 seconds until computer finish measuring.
-
LCD will display: FAT%, BMR, BMI & BODY TYPE:
NOTE
Correct “User Profile Settings” is required for this function.
Male | Female |
---|---|
1 | 7.0%~ 9.9% |
2 | 10.0% to 12.9%. |
3 | 13.0% to 16.9%. |
4 | 17.0% to 19.9%. |
5 | 20.0% to 24.9%. |
6 | 25%. + |
-
Use UP/ DOWN key to set TIME,
Range: 0:00 – 5:00 ~ 99:00 ±1:00 confirm setting by pressing ENTER. -
Use UP/ DOWN key to set DISTANCE,
Range: 00.00 – 00.10 ~ 99.90 ± 00.10 confirm setting by pressing ENTER. -
Use UP/ DOWN key to set CALORIES,
Range: 0.0 – 1.0 ~ 999.0 ± 1.0 confirm setting by pressing ENTER. -
Use UP/ DOWN key to set pulse (TARGET HR) limit Range: 0 – 72 ~ 240 ± 1 confirm setting by pressing ENTER.
NOTE
- When setting more than one goal, the training will end at first achieved goal.
- Continue the workout by pressing START/ STOP button, and training will end again at first next achieved goal.
- Leave a goal blank and it will not be seen as a pre-set limit.
- Set Pulse limit is resistance control function, Resistance will auto lower when value is over pulse target, and auto upper when under pulse target.
- Press START/ STOP key to start workout
- Use UP/ DOWN key to adjust resistance level. Load level is shown in LEVEL window.
- Press START/ STOP key to pause workout.
- Press and hold START/ STOP key for over 2 seconds to reset console and to go back to main menu. (Active training data will be lost)
H.R.C. mode. (Program 13~15)
-
Use UP/ DOWN key to select Program 13~15 P13= 60% 60% of (220-Age)
P14= 75% 75% of (220-Age)
P14= 85% 85% of (220-Age) and press ENTER to confirm. -
Use UP/ DOWN key to set TIME,
Range: 0:00 – 1:00 ~ 99:00 ±1:00 confirm setting by pressing ENTER. -
Use UP/ DOWN key to set DISTANCE, Range: 00.00 – 00.10 ~ 99.90 ± 00.10 confirm setting by pressing ENTER.
-
Use UP/ DOWN key to set CALORIES, Range: 0.0 – 1.0 ~ 999.0 ± 1.0 confirm setting by pressing ENTER.
-
Use UP/ DOWN key to set Age,
Range: 10 ~ 99 ± 1 confirm setting by pressing ENTER
NOTE
- When setting more than one goal, the training will end at first achieved goal.
- Continue the workout by pressing START/ STOP button, and training will end again at first next achieved goal.
- Leave a goal blank and it will not be seen as a pre-set limit.
- Set Pulse limit is resistance control function, Resistance will auto lower when value is over pulse target, and auto upper when under pulse target.
- Press START/ STOP key to start workout
- Use UP/ DOWN key to adjust resistance level. Load level is shown in LEVEL window.
- Press START/ STOP key to pause workout.
- Press and hold START/ STOP key for over 2 seconds to reset console and to go back to main menu.
(Active training data will be lost)
User program (P16 ~ P19)
-
Use UP/ DOWN key to select Program 16 ~ 19 and press ENTER to confirm.
-
Use UP/ DOWN key to set TIME,
Range: 0:00 – 1:00 ~ 99:00 ±1:00 confirm setting by pressing ENTER. -
Use UP/ DOWN key to set DISTANCE,
Range: 00.00 – 00.10 ~ 99.90 ± 00.10 confirm setting by pressing ENTER. -
Use UP/ DOWN key to set CALORIES,
Range: 0.0 – 1.0 ~ 999.0 ± 1.0 confirm setting by pressing ENTER. -
Use UP/ DOWN key to set Age,
Range: 10 ~ 99 ± 1 confirm setting by pressing ENTER. -
Set tension level for first of 10 columns, and confirm with ENTER to set second level, repeat this for all colums.
-
Press START/ STOP key to start workout
-
Use UP/ DOWN key to adjust resistance level.
-
Press START/ STOP key to pause workout.
-
Press and hold START/ STOP key for over 2 seconds to reset console and to go back to main menu.
(Active training data will be lost, but set program profile will be stored )
Recovery
F1 | Outstanding |
---|---|
F2 | Excellent |
--- | --- |
F3 | Good |
F4 | Fair |
F5 | Below average |
F6 | Poor |
- The RECOVERY key will only be valid if pulse is detected.
- TIME will show „0:60“ (seconds) and counts down to 0.
- Computer will show F1 to F6 after the countdown to test heart rate recovery status. User can find the heart rate recovery level based on the chart below.
- Press RECOVERY key again to return to the beginning.
Trouble shooting:
- If there is no signal when you pedal, please check if the cable is well connected.
NOTE
- When stop training for 4 minutes, the main screen will be off.
- If the computer displays abnormally, please re-install the transformer and try again.
Cleaning and maintenance
The equipment does not require special maintenance. The equipment does not require recalibration when it is assembled, used and serviced according to the instructions.
WARNING
- Do not use solvents to clean the equipment.
- Clean the equipment with a soft, absorbent cloth after each use.
- Regularly check that all screws and nuts are tight.
- If necessary, lubricate the joints.
Defects and malfunctions
Despite continuous quality control, defects and malfunctions caused by
individual parts can occur in the equipment. In most cases, it will be
sufficient to replace the defective part.
- If the equipment does not function properly, immediately contact the dealer.
- Provide the model number and the serial number of the equipment to the dealer. State the nature of the problem, conditions of use and purchase date.
Transport and storage
WARNING
- Carry and move the equipment with at least two persons.
- Remain standing in front of the equipment on each side and take a sturdy grip at the handlebars. Tilt the front of the equipment so as to lift the rear of the equipment on the wheels. Move the equipment and carefully put the equipment down. Place the equipment on a protective base to prevent damage to the floor surface.
- Move the equipment carefully over uneven surfaces. Do not move the equipment upstairs using the wheels, but carry the equipment by the handlebars.
- Store the equipment in a dry place with as little temperature variation as possible.
Additional information
Packaging disposal
Government guidelines ask that we reduce the amount of waste material disposed
of in land fill sites. We therefore ask that you dispose of all packaging
waste responsibly at public recycling centres.
End of life disposal
We at Tunturi hope you enjoy many years of enjoyable use from your fitness
trainer. However, a time will come when your fitness trainer will come to the
end of its useful life. Under ‘European WEEE Legislation you are responsible
for the appropriate disposal of your fitness trainer to a recognised public
collection facility.
Technical data
Parameter | Unit of measurement | Value |
---|
Length
|
cm inch
|
98
38.6
Width| cm inch| 55
21.7
Height| cm inch| 137
53.9
Weight| kg
lbs
| 30.0
66.1
Max. user weight| kg
lbs
|
120
265
---|---|---
Adapter Voltage Current|
V
Ma.
|
9V-DC
0.5A
Warranty
Tunturi purchaser‘s warranty
Warranty terms
The consumer is entitled to the applicable legal rights stated in the national
legislation concerning the commerce of consumer goods. This warranty does not
restrict these rights. The Purchaser’s Warranty is only valid if the item is
used in an environment approved by Tunturi New Fitness BV for that particular
equipment. The product-specific approved environment is stated in the Owner’s
Manual provided with your equipment.
Warranty conditions
The warranty conditions commence from the date of purchase. Warranty
conditions may vary per country, so please consult your local dealer for the
warranty conditions.
Warranty coverage
Under no circumstances shall Tunturi New Fitness BV or the Tunturi Distributor
be liable by virtue of this warranty or otherwise for any special, indirect,
secondary or consequential damages of any nature arising out of any use or
inability to use this equipment.
Warranty limitations
This warranty covers manufacturing defects in the fitness equipment as
originally packed by Tunturi New Fitness BV. The warranty shall apply only
under conditions of normal, recommended use of the product as described in the
Owner’s Manual and providing that Tunturi New Fitness BV’s instructions for
installation, maintenance and use have been complied with. Neither Tunturi New
Fitness BV’s nor the Tunturi Distributors’ obligations apply to defects due to
reasons beyond their control. The warranty applies only to the original
purchaser and is valid only in countries where Tunturi New Fitness BV has an
authorised importer. The warranty does not extend to fitness equipment or
components that have been modified without the consent of Tunturi New Fitness
BV. Defects resulting from normal wear, misuse, abuse, corrosion, or damage
incurred during loading or transportation are not covered. The warranty does
not cover sounds or noises emitted during use where these do not substantially
impede the use of the equipment and where they are not caused by a fault in
the equipment. The warranty does not cover defects arising from the failure to
carry periodic maintenance as outlined within the Owner’s Manual for the
product. Furthermore, the warranty does not cover defects arising from usage
and storage within an unsuitable environment as described within the Owner’s
Manual which should be indoors, dry, dust and grit free and within a
temperature range of +15°C to +35°C. The warranty does not cover maintenance
activities, such as cleaning, lubricating, and normal part adjustments, nor
installation
procedures that customers can accomplish themselves, such as changing
uncomplicated meters, pedals and other similar parts not requiring any
dismantling/reassembling of the fitness equipment. Warranty repairs carried
out by other than authorised Tunturi representatives are not covered.
Failure to follow the instructions given in the Owner’s Manual will invalidate
the product’s warranty.
Declaration of the manufacturer
Tunturi New Fitness BV declares that the product is in conformity with the
following standards and directives: EN 957 (HC), 89/336/EEC. The product
therefore carries the CE label.
07-2018
Tunturi New Fitness BV
Purmerweg 1
1311 XE Almere
The Netherlands
Disclai m er
© 2018 Tunturi New Fitness BV
All rights reserved.
The product and the manual are subject to change. Specifications can be
changed without further notice.
1 | Main frame | 1 | |
---|---|---|---|
2 | Rear stabilizer | 1 | |
3 | Front stabilizer | 1 | |
4 | End cap for stabilizer | 4 | |
5 | Cover for seat post | 1 | |
6 | Allen screw | M8x55 | 4 |
7 | Curved washer | Ø8×20 | 8 |
8 | Spring washer | Ø8 | 7 |
9 | Left pedal | 1 | |
10 | Right pedal | 1 | |
11 | Quick release knob | 1 | |
12 | Washer | Ø17xØ8 | 4 |
13 | Grommet | 1 | |
14 | Nylon nut | M8 | 7 |
15 | Seat post | 1 | |
16 | Seat | 1 | |
17 | Allen screw | M8x16 | 4 |
18 | Computer | 1 | |
19 | Handlebar | 1 | |
20 | Bottle holder | 1 | |
21 | Motor wire | 1 | |
22 | Front post | 1 | |
23 | Lower computer wire | 1 | |
24 | Upper computer wire | 1 | |
25 | Clamp | 1 | |
26 | Allen screw | M8x20 | 2 |
27 | Cover for clamp | 1 | |
28 | T-type knob | 1 | |
29 | Screw | M5x12 | 4 |
30 | Sliding tube | 1 | |
31 | Tapered nut | 1 | |
32 | Big washer | 1 | |
33 | Sleeve | 1 | |
34 | L Type Knob | 1 | |
35 | End cap for handlebar | 2 | |
36 | Foam for handlebar | 2 | |
37 | Hand pulse sensor | 2 | |
38 | Washer | 2 | |
39 | Screw | 2 | |
40 | Seat post bushing | 1 | |
41 | Transport wheel | 2 | |
42 | Bearing | 4 | |
43 | Hand pulse wire | 2 | |
44 | Axle for flywheel | 1 | |
45 | C-clip | 2 | |
46 | Bearing | 6001 | 2 |
47 | End cap for crank | 2 | |
48 | Decorating ring for seat |
post
| | 1
49| Allen screw| M8x40| 2
50| Leveling pad| | 4
51| Flange nut| | 4
52| Allen screw| M8x105| 1
53| Axle for pulley| | 1
54| Bearing| 6203| 2
55| Belt pulley| | 1
56| Flywheel| | 1
57| Idler wheel assembly| | 1
58| Belt| | 1
59| Magnet assembly| | 1
60| Bushing| | 2
61| Adjusting bolt| | 1
62| Hex head nut| M8| 1
63| Spring for idler wheel| | 1
64| Powder spacer| | 1
65| Spring| | 1
66| Hex head bolt| M6x25| 1
67| Hex head nut| M6| 2
68| Sensor bracket| | 1
69| Decorating ring for front
post
| | 1
70| Self-tapping screw| | 17
71| Self-tapping screw| 15mm| 13
72| Chain cover R| | 1
73| Chain cover L| | 1
74 L| Front chain cover L| | 1
74 R| Front chain cover R| | 1
75| C-clip| | 2
76| Nylon nut| M6| 4
77| Allen screw| 15mm| 4
78| Motor| | 1
79 L| Crank L| | 1
79 R| Crank R| | 1
80| Sensor wire| | 1
81| Power wire| | 1
82| Adaptor| 9V-DC/
0.5 Amp
| 1
83| Nut| M10| 4
Tunturi New Fitness BV
Purmerweg 1 NL – 1311 XE Almere
P.O. Box 60001 NL – 1320 AA Almere
The Netherlands
www.tunturi-fitness.com
info@tunturi-fitness.com