TUNTURI E60-R Recumbent Exercise Bike Instruction Manual

: June 6, 2024
: Tunturi

Table of Contents

TUNTURI E60-R Recumbent Exercise Bike
Safety warnings
Electrical safety
Assembly instructions
Additional assembly information.
HOW CAN USE
Additional information
Declaration of the manufacturer
Disclaimer
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TUNTURI E60-R Recumbent Exercise Bike

Safety warnings

WARNING

Read the safety warnings and the instructions. Failure to follow the safety warnings and the instructions can cause personal injury or damage to the equipment. Keep the safety warnings and the instructions for future reference.
Heart rate monitoring systems may be inaccurate.
Over-exercise may result in serious injury or death. If you feel faint stop exercising immediately.
- The equipment is suitable for domestic use only. The equipment is not suitable for commercial use.
- Max. usage is limited to 5 hrs a day. The use of this equipment by children or persons with a physical, sensory, mental, or motor disability, or lack of experience and knowledge can give cause to hazards. Persons responsible for their safety must give explicit instructions or supervise the use of the equipment.
- Before starting your workout, consult a physician to check your health.
- If you experience nausea, dizziness, or other abnormal symptoms, immediately stop your workout and consult a physician.
- To avoid muscular pain and strain, start each workout by warming up and finish each workout by cooling down. Remember to stretch at the end of the workout.
- The equipment is suitable for indoor use only. The equipment is not suitable for outdoor use.
- Only use the equipment in environments with adequate ventilation. Do not use the equipment in draughty environments in order not to catch a cold.
- Only use the equipment in environments with ambient temperatures between 10°C~35°C/ 50°F~95°F. Only store the equipment in environments with ambient temperatures between 5°C~45°C/ 41°F~113°F.
- Do not use or store the equipment in humid surroundings. The air humidity must never be more than 80%.
- Only use the equipment for its intended purpose. Do not use the equipment for other purposes than described in the manual.
- Do not use the equipment if any part is damaged or defective. If a part is damaged or defective, contact your dealer.
- Keep your hands, feet, and other body parts away from the moving parts.
- Keep your hair away from the moving parts.
- Wear appropriate clothing and shoes.
- Keep clothing, jewelry, and other objects away from the moving parts.
- Make sure that only one person uses the equipment at a time. The equipment must not be used by persons weighing more than 135 kg (300 lbs).
- Do not open equipment without consulting your dealer.

Electrical safety

Before use, always check that the mains voltage is the same as the voltage on the rating plate of the equipment.
Do not use an extension cable.
Keep the mains cable away from heat, oil, and sharp edges.
Do not alter or modify the mains cable or the mains plug.
Do not use the equipment if the mains cable or the mains plug is damaged or defective. If the mains cable or the mains plug is damaged or defective, contact your dealer.
Always fully unwind the mains cable.
Do not run the main cable underneath the equipment. Do not run the main cable underneath a carpet. Do not place any objects on the main cable.
Make sure that the main cable does not hang over the edge of a table.
Make sure that the main cable cannot be caught accidentally or tripped over.
Do not leave the equipment unattended when the mains plug is inserted into the wall socket.
Do not pull the mains cable to remove the mains plug from the wall socket.
Remove the mains plug from the wall socket when the equipment is not in use, before assembly or disassembly, and before cleaning and maintenance.

Assembly instructions

Description illustration A

The illustration shows what the trainer will look like after the assembly is completed. You can use this as a reference during your assembly, but do follow the assembly steps always in the correct sequence as shown in the illustrations.

Description illustration B

The illustration shows what components and parts you should find when unboxing your product.

NOTE

Small parts can be hidden/ packed in hollow spaces in the Styrofoam product protection
If a part is missing, contact your dealer.

Description illustration C

The illustration shows the hardware kit that comes with your product. The hardware kit contains bolts, washers, screws, nuts, etc., and the required tools to properly fit your trainer.

Description illustration D

The illustrations show you in the correct following order how to assembly your trainer best.

NOTE

Part numbers shown in the assembly steps are commencing with the spare part drawing that can be found in the online full version user manual.

WARNING

Assemble the equipment in the given order.
Carry and move the equipment with at least two persons.

CAUTION

Place the equipment on a firm, level surface.
Place the equipment on a protective base to prevent damage to the floor surface.
Allow at least 100 cm of clearance around the equipment.
Refer to the illustrations for the correct assembly of the equipment.

Additional assembly information.

D3 How to fit the pedals correctly.

NOTE

The right and left sides are determined from an exercising position’s perspective.

Right-hand pedal

Find the “R” or “L” mark on the pedal axle

Fit the right-hand pedal “R” into the right-hand crank.
Firstly turn the pedal axle in a clockwise direction by hand.
Use the wrench to fully tighten the pedal.

Left-hand pedal

Fit the left-hand pedal “L” into the left-hand crank.
Firstly turn the pedal axle in a counter-clockwise direction by hand.
Use the wrench to fully tighten the pedal.

Additional information to Assembly step D5

Establish the wire connection between the cable coming from the mainframe, and the lower part of the cable pre-fitted in the upright tube.
Place the upright tube over the mainframe fixing bracket, where the fixing bolts are pre-assembled and stay pre-assembled. ( While lowering the upright tube, gently pull the upper part of the cable up, to avoid the cable get caught by the connection. )
The upright tube should automatically find the center position, but it is advisable to make the slightest correction needed to make sure the position is good.
The perfect position is when the fixing bolts are perfectly centered in line with the upright tube holes.

NOTE

Avoid the cable connection between these two parts getting pinched.
By fastening the two bolts (turning in a clockwise direction) on the front side you will widen the fixing bracket so the upright gets fixed firmly.
- To fix the upright tube firmly it is needed to tighten the bolt on the upper side first firmly.
- After fixing the upper bold, you need to fix the lower bold firmly.
- By fixing the lower bold, the upright tube will be repositioned slightly resulting that the upper bold can be fixed a little more, therefore it is needed to fix the upper bolt again.
- Repeat these steps until both bolts are firmly fixed to ensure the upright tube fixation well.
Save the tools provided with this product, after you complete the product assembly, for future service purposes.

HOW CAN USE

Adjusting the support feet The equipment is equipped with 5 support feet. If the equipment is not stable, the support feet can be adjusted.

Turn the support feet as required to put the equipment in a stable position.
Tighten the locknuts to lock the support feet.
NOTE The machine is the most stable when all support feet are turned fully in. Therefore start to level the machine by turning all support feet fully in, before turning out the required support feet to stabilize the machine.

Adjusting the horizontal seat position

The horizontal seat position can be adjusted by setting the seat to the required position.

Loosen the quick-release lever under the seat.
Slide the seat forward or backward as desired.
Tighten the quick-release lever.

Adjusting the backrest inclination

Loosen the backrest inclination adjustment knob.
Move the backrest to the required position.
Tighten the backrest inclination adjustment knob.

Adjusting the backrest height

Loosen the backrest height adjustment knob.
Move the backrest to the required position.
Tighten the backrest adjustment knob.

Power supply (Fig. E)

The trainer is powered by an external power supply. Refer to the illustration to locate the trainer power input.

NOTE

Connect the power supply with the trainer before connecting it to the wall outlet.
Always remove the power cord when the machine is not in use.

Master power switch (fig. E)

The equipment is equipped with a master power switch to shut down the equipment completely.

Additional information

Packaging disposal Government guidelines ask that we reduce the amount of waste material disposed of in landfill sites. We, therefore, ask that you dispose of all packaging waste responsibly at public recycling centers.
End-of-life disposal We at Tunturi hope you enjoy many years of enjoyable use from your fitness trainer. However, a time will come when your fitness trainer will come to the end of its useful life. Under ‘European WEEE Legislation you are responsible for the appropriate disposal of your fitness trainer to a recognized public collection facility.

Warranty

Tunturi purchaser‘s warranty Warranty terms The consumer is entitled to the applicable legal rights stated in the national legislation concerning the commerce of consumer goods. This warranty does not restrict these rights. The Purchaser’s Warranty is only valid if the item is used in an environment approved by Tunturi New Fitness BV for that particular equipment. The product- specific approved environment is stated in the Owner’s Manual provided with your equipment.

Declaration of the manufacturer

Tunturi New Fitness BV declares that the product is in conformity with the following standards and directives: EN 957 (HB), 2014/30/EU. The product, therefore, carries the CE label.