SounDigital EVOX2 2OHM Owner’s Manual

June 9, 2024
SOUNDIGITAL

YOUR MUSIC. YOUR POWER.
OWNER´S MANUAL
400.4 EVOX2

INTRODUCTION

DEAR CUSTOMER,
CONGRATULATIONS ON ACQUIRING A PRODUCT WITH THE HIGHEST QUALITY AND TECHNOLOGY!
You have just purchased a SounDigital product of the highest technology and quality, so we thank you for your confidence.
SounDigital products are made with raw materials of the highest quality standards, and the most modern processes, equipment and technology are used in their production.
On this manual you will learn about the product, its features and characteristics, in order to obtain the best result and to be able to enjoy your music with SounDigital quality and power.
To better understand and take advantage of all the functions of the product and use it safely, read this manual carefully and if you have any questions, consult our support by email info@soundigitalusa.com.

PACKAGE CONTENTS

  • 01 400.4 EVOX2 Amplifier
  • 01 Installation quick guide with warranty card
  • 01 Allen wrench 2.0mm
  • 02 Cables for high level input
  • 01 Promotional sticker

SAFETY INSTRUCTIONS

To prevent injuries to the user or damage to the amplifier, read all safety instructions written on this manual;
If you are insecure about the installation of this equipment, get in touch with our tech support or with a professional specialized in car audio installation;
Before proceeding with the installation of any electric equipment on your vehicle, unplug the negative (-) terminal of the battery to avoid fires, injuries or damages;
Use your sound system safely. The continuous exposure to sound pressures over 85dB may cause irreversible hearing damage;
This equipment is for use in automotive DC voltage batteries between 12.6 and 14.4 volts. Before installing the equipment, check voltage of the batteries;
Do not install the amplifier in places exposed to water, dirt or humidity;
Choose a ventilated place to install the amplifier and avoid blocking the side ventilation windows;
Mount the amplifier in a secure way. Avoid mounting it on metallic parts of the vehicle, because it may cause ground looping (noise);
Make sure that the location chosen for the amplifier installation does not effect the operation of the vehicle;
When passing cables through metallic walls, use rubber O-rings to avoid cable cutting and short-circuits;
Clean the amplifier periodically with brush or dry cloth to assure the thermal efficiency of the heatsink;
This product may reach temperatures over 60°C/140°F. Make sure it is cold before touching it;
Be careful when making holes in the vehicle. Make sure you are not making holes in the fuel tank, brake lines or electrical cables of the vehicle;
Make sure the cables are properly secured throughout the installation;
Wear gloves, safety glasses and and all necessary PPE during the installation of SounDigital amplifiers.

Warning!
THIS “WARNING” SIGN ALERTS THE USER OF IMPORTANT INFO. NOT FOLLOWING THIS INSTRUCTIONS MAY CAUSE INJURIES TO THE USER OR DAMAGE TO THE EQUIPMENT.

TECHNOLOGIES

DYNAMIC THERMAL MANAGEMENT – DTM®

SounDigital EVOX2 2OHM -

The DTM* is a dynamic thermal recovery system which always maintains a high efficiency of the amplifier by accelerating the thermal exchange of electronic components with the heatsink.

  • Patent. Required

ULTRA COMPACT PCB
An intelligent layout, with great use of the PCB area and the use of modern components with reduced structure guarantee SounDigital products a compact design, at the same time robust and with excellent thermal efficiency.

ROBUST CONSTRUCTION
Thinking about the application of power sports, the product has an extremely robust assembly, both the fixing points and the layout of the PCB were designed to withstand high vibrations, bumps and impacts.

I-POWER SUPPLY
SounDigital amplifiers are known for their low consumption of battery, and this feature was improved on the EVOX2 Line. The new I-POWER SUPPLY is even more modern, which replaces the old to roidal trans formers by a new generation of “E-E” core transformers delivers efficiency above 90%, ensuring more hours of sound without battery recharge.
Efficiency measured at power supply only

VIBRATION ABSORPTION DEVICE – VAD®
Our VAD® Technology reduces all impact caused by vibration on the electronic circuit board. This can include road vibration and even vibration caused by sound waves, increasing the reliability of our amplifiers.SounDigital EVOX2
2OHM - ABSORPTION

REDUCED SIZE
The technology used in our amplifiers bring both high performance and power a compact chassis, providing flexible installation solutions for vehicles with limited space. SounDigital EVOX2 2OHM - REDUCED SIZE

FULL RANGE
Versatile products that cover the entire audible frequency range, any type of loudspeaker or music program.

ASSEMBLING AND DISASSEMBLING THE PLASTIC COVER

The plastic covers have the function of finishing and hiding the amplifier fixing screws. To disassembling and assembling them, follow the instructions below.

DISASSEMBLING OF THE PLASTIC COVER

| |
---|---|---

  1. Carefully pull out the top of plastic cover to release the upside latches, as shown in the picture 1.
  2. Slide up the plastic cover in a continuous movement to remove it.

*Merely illustrative images.

ASSEMBLING THE PLASTIC COVER

SounDigital EVOX2 2OHM - 4|
---|---

  1. To fit the plastic cover back, carefully insert the point A of the plastic cover into point B of the amplifier, slowly sliding it down.
  2. Gently press the sides of the top of the plastic cover towards the bottom of the amplifier until you hear a clicking noise.

PANELS DESCRIPTION

SounDigital EVOX2 2OHM - PANELS DESCRIPTION

1 CH1/CH2 Variable crossover control – 45Hz to 850Hz
2 CH3/CH4
3 CH1/CH2 Audio inputs – High Level (To connect to the speaker output of the

head unit)
4| CH3/CH4
5| CH1| Audio inputs – RCA connectors
6| CH2
7| CH3
8| CH4
9| CH1/CH2| Crossover Switch Low Pass – Full – High Pass
10| CH3/CH4
11| CH1/CH2| Variable Gain Control
12| CH3/CH4

SounDigital EVOX2 2OHM - PANELS DESCRIPTION1

13 CH1 Positive speaker connector
14 CH1 Negative speaker connector
15 CH2 Positive speaker connector
16 CH2 Negative speaker connector
17 CH3 Positive speaker connector
18 CH4 Positive power supply connector (+12VDC)
19 CH4 Negative speaker connector
20 CH3 Positive speaker connector
21 Negative speaker connector
22 Remote power supply connector (REM)
23 Negative power supply connector (GND)
24 Power ON LED indicator (Blue)

INSTALLATION SEQUENCE

Warning!
BEFORE PROCEEDING WITH THE INSTALLATION, UNPLUG THE NEGATIVE TERMINAL FROM ALL OF THE BATTERIES, TO AVOID FIRE, DAMAGE TO THE AMPtJFIER AND THE USER HIMSELF.

  • Mount the amplifier in such a way you have access to the connectors;
  • Install the power cables in the vehicle properly, starting from the battery to the fuse holder or circuit breaker, use the cable with the appropriate size. Make all
    connections, install fuse holders or circuit breakers, but without placing the fuses or with the circuit breakers in the “OFF” position;

Warning!
THE MAXIMUM DISTANCE FOR THE INSTALLATION OF THE FUSE/CIRCUIT BREAKER IS 12 INCHES (30cm) AWAY FROM THE BATTERY.

  • Connect the power cables in to the amplifier, observing the polarity. Connect all the positive cables from the fuse holder or circuit breaker to the positive conector of the amplifier and all the negative power cables from the batteries to the negative connector of the amplifier;
  • The ground cable must be as short as possible and must be connected to the vehicle chassis and the battery negative;SounDigital EVOX2 2OHM - paint between
  • Install the signal input cables in a proper way, distant from the power cables;
  • Connect the RCA or the high level signal input cables to the head unit and amplifiers;
  • Install the audio output cables with the appropriate section, distant from the power and audio input cables;
  • Connect the audio output cables to the amplifier and speakers respecting the positive (+) and negative (-) polarities;
  • Install the remote cable with the power cables, using 1.5mm² (15 AWG) cable or thicker;
  • Connect the remote power cable to the amplifier’s “REM” terminal at the main unit’s remote power output (when not using the high level signal inputs);
  • Before powering the system, verify all the connections and make sure there are no mistakes or short-circuits on the power and ground cables;
  • Reconnect the ground of the batteries;
  • Check if the head unit is turned off and then place the fuses in the fuse holders or switch the circuit breakers on;
  • Turn on the main unit and the amplifier will turn on the “ON” LED indicating that it is in operation.

ELECTRICAL DIMENSIONING AND AUDIO INPUTS

ELECTRICAL DIMENSIONING
For proper operation of your SounDigital amplifier, you need the proper dimensioning of the electrical system and the cables used.
The table below shows the minimum section of GND cables, +12VDC cables and speaker output cables according to the power generated by the amplifier.

400 WRMS POWER CABLE GROUND CABLE 8mm² – 8 AWG
SPEAKER CABLE 2 x 1.5mm² – 15 AWG

We recommend the use of ONLY OFC (Oxygen Free Copper) Cables on the installation of our products.

AUDIO INPUTS
RCA inputs

SounDigital EVOX2 2OHM - AUDIO INPUTS

All RCA Inputs must be connected for the all channels to work properly.

High level signal inputs

All High level signal Inputs must be connected for the all channels to work properly.

High level input must be used when the main unit does not have RCA outputs.
When High level inputs is used, no remote connection is required, the amplifier recognizes the audio signal and switches on.
If your source unit is not able to turn on the amplifier through the High level input, the remote input should be connected normally.

Warning!
RCA AND HIGH LEVEL INPUTS SHOULD NOT BE USED SIMULTANEOUSLY OR YOU MAY DAMAGE THE AMPLIFIER.

WIRING DIAGRAM

4 CHANNELS WIRING DIAGRAM

SounDigital EVOX2 2OHM - WIRING DIAGRAM

All RCA Inputs must be connected for the all channels to work properly.

Minimum impedance

Model Per channel Bridge
400.4 EVOX2

3 CHANNELS WIRING DIAGRAM

SounDigital EVOX2 2OHM - WIRING DIAGRAM1

All RCA Inputs must be connected for the all channels to work properly.

Minimum impedance

Model Per channel Bridge
400.4 EVOX2

WIRING DIAGRAM / GAIN SETTING

2 CHANNELS WIRING DIAGRAM

SounDigital EVOX2 2OHM - WIRING DIAGRAM2

All RCA Inputs must be connected for the all channels to work properly.

Model Per channel Bridge
400.4 EVOX2

GAIN SETTING
Necessary equipament:

  • Digital AC voltmeter;
  • Media with sine wave test tone 60Hz recorded at 0db;
  • Screwdriver 1/8″ ( for gain set); Set up procedure
  • This procedure is the same for both gain controls;
  • Turn the gain control all the way down;
  • Disconnect the output cables from the amplifier outputs;
  • Turn off all processing (bass, treble, loudness, EQ, etc.);
  • Set the source unit volume to 3/4 of full volume;
  • On the CD player, set the fader control to center position;
  • Set the crossover selector switch in “F”;
  • Use a 60 Hz sine wave;
  • Connect the AC voltmeter to the speaker output connectors of the amplifier. Make sure you test the voltage at the correct connectors (+ and –);
  • Increase the gain control until the target voltage is observed with the voltmeter (see the chart below);
  • Once you have adjusted the amplifier to its correct voltage output, turn off the source unit and reconnect the speaker(s).
    Download the tracks for set up in https://soundigitalusa.com/tracks-forset- up/

MODEL| STEREO / POWER| BRIDGE / POWER| STEREO OUTPUT VOLTAGE| BRIDGE OUTPUT VOLTAGE
---|---|---|---|---
400.4| 2Ω /100W| 4Ω / 200W| 14.14 V| 28.3 V

CROSSOVER SET UP

“F” All the frequencies are reproduced;
“LP ” Set in the variable control on Low Pass Function;
“HP ” Set in the variable control on High Pass Function.

  • Change the switch to “F” position (Full Range): All the frequencies are reproduced.SounDigital EVOX2 2OHM - reproduced
  • Change the switch to “HP” position – Set in the variable control between 45Hz and 850Hz (“A”) where you want to perform the high pass cut filter;SounDigital EVOX2 2OHM - Change the switch
  • Change the switch to “LP” position – Set in the variable control between 45Hz and 850Hz (“B”) where you want to perform the low pass cut filter;SounDigital EVOX2 2OHM - variable control between

TECHNICAL SPECS

PARAMETERS 400.4 EVOX2
RMS Power Bridge @ 8Ω** 2 x 132W
RMS Power Bridge @ 4Ω** 2 x 200W
RMS Power @ 4Ω** 4 x 66W
RMS Power @ 2Ω** 4 x 100W
Frequency Response (-3dB) 5Hz ~ 22kHz
Low Pass filter (12dB/Oct.) 45Hz ~ 850Hz
High Pass filter (12dB/Oct.) 45Hz ~ 850Hz
Operating Voltage 8V ~ 16V
SNR 96dB
Input Sensitivity 0.2 ~ 2V
Current Draw (music) 16A
Current Draw (max.) 33A
Total Efficiency 83%
Damping Factor 200
Power Cable 8mm² (8 AWG)
Audio Output Cable 2 x 1.5mm² (15 AWG)
Fuse* (music) 20A
Recommended battery (minimum) 20Ah

*It is mandatory to install the fuse at a maximum distance of 12 inches from the battery.
**Power at 14.4V @ 60Hz with a maximum THD of 1%.

**REAL POWER NUMBERS
CTA-2006 INDUSTRY STANDARDS

DIMENSIONAL DATA

SounDigital EVOX2 2OHM - DIMENSIONAL DATA

Net Weight 1.12 lb (0.51 kg)
Gross Weight 1.30 lb (0.59 kg)

YOUR MUSIC. YOUR POWER.SounDigital EVOX2 2OHM -
icon2 WWW.SOUNDIGITALUSA.COM
SOUNDIGITALUSA
SOUNDIGITALUSA

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SOUNDIGITAL User Manuals

Related Manuals