MY CHILD Walk ‘n’ Rock 2-in-1 Walker Instruction Manual

MY CHILD Walk ‘n’ Rock 2-in-1 Walker

IMPORTANT! READ CAREFULLY AND KEEP IT FOR FUTURE REFERENCE
This product is intended only for a child who can sit up by himself until she is able to walk by himself or weighs more than 12 kg.
BS EN 1273:2020.

Safety instructions

WARNING:

• Never leave the child unattended.
• The child will be able to reach further and move rapidly when in the baby walking frame:
• Prevent access to stairs, steps and uneven surfaces.
• Guard all fires, heating and cooking appliances.
• Remove hot liquids, electrical cables and other potential hazards from reach.
• Prevent collisions with glass in doors, windows and furniture.
• This product is intended only for a child who can sit up by itself and until it is able to walk by itself or weighs more than 12 kg.
• This baby walking frame should be used only for short periods of time (e.g. 20 min).
• Do not use the product if any components are broken or missing.
• Do not use accessories or replacement parts other than those approved by the manufacturer.
• Never use the baby walking frame without the supplied anti-fall blocks attached.
• Never use the baby walking frame without the supplied wheels attached.

Battery warnings

• Only use the recommended batteries observing the correct voltage and size.
• Always take care to insert your batteries correctly, observing the plus and minus marks on the battery and appliance.
• Do not mix new and used batteries.
• Do not mix different types of batteries.
• Always remove batteries (whether they are dead or not) if you are not going to use the product for long periods (as batteries may leak and cause damage).
• Never attempt to recharge ordinary (non-rechargeable) batteries.
• Remove rechargeable batteries before attempting to charge them.
• Do not short-circuit the supply terminals
• Batteries should always be changed by an adult.
• Keep batteries out of reach of children.
• Children can choke on batteries. If swallowed seek medical advice immediately.

Battery disposal
The crossed-out wheelie bin symbol indicates that the product must not be disposed of with other household waste. Do not treat batteries (old or new) as household waste. Never dispose of batteries in a fire this may cause them to explode. Batteries (old or new) should be disposed of by taking them to a designated collection point or recycling facility.

Care and maintenance

• To prolong the life of your nursery product keep it clean and do not leave it in direct sunlight for extended periods of time.
• Removable fabric covers and trims may be cleaned using warm water with household soap or a mild detergent. Allow it to dry fully, preferably away from direct sunlight.
• If the wheels squeak – use a silicon-based spray ensuring it penetrates the wheel and axle assembly.
• Do not dry clean, or use bleach.
• Do not machine wash, tumble or spin dry, unless the care labeling on the product permits these methods.
• Nonremovable fabric covers and trims may be cleaned using a damp sponge with soap or mild detergent. Allow it to dry completely before folding or storing it away.
• In some climates the covers and trims may be affected by mold and mildew. To help prevent this from occurring, do not fold or store the product if it is damp or wet. Always store the product in a well-ventilated area.
• Always check parts regularly for tightness of screws, nuts, and other fasteners – tighten if required. If any parts are bent, torn, worn or broken please contact Customer Service.

Your 3-year warranty

Whilst we make and test our products to the highest standards of durability there’s always a small chance of a hiccup! Our promise is to repair, replace or refund a MyChild product that has an identified manufacturing defect from the date of purchase for a full 3 years thereafter at no extra cost.

However, you must register within 28 days of the date of purchase to receive the full 3 years guarantee!

To receive your full guarantee you can register your product by: visiting https://mychild.co.uk/pages/warranty and completing the warranty form, or by telephone at 0161 335 2508.

Welcome
Thank you for purchasing the MyChild Walk ‘n’ Rock 2-in-1 Walker.

Please read the instructions and warnings carefully before use to ensure the safe and satisfactory operation of this product. Your child’s safety is your responsibility. If you have a query with this product or require replacement parts, please contact the MyChild Helpline on 0161 335 2508. Lay out the parts on a soft-level surface and compare to the part/fixings checklist below. Do not discard any packaging until you are sure that you have all the parts.

WARNING!
Assembly by an adult. Keep away from children until fully assembled. Keep children clear during assembly as the pack contains small parts which may present a choking hazard.

Parts checklist

Contained in your carton are:

N o| Part| Qty
1| Walker body| 1
2| Seat unit| 1
3| Musical play tray| 1
4| Footrest pad| 1
5| Front wheels| 2
6| Rear wheels| 2
7| Wheel pusher| 1
8| Anti-fall blocks| 8
9| Flexi toys| 2
10| Toy rings| 3

You will require one Phillips screwdriver (not supplied).

Opening and closing the baby walker

1. To open: hold either side of the upper part of the walker and pull upwards to one of the three height positions. Ensure the upper part of the walker clicks into position.
   Note: There is a click for each of the three height positions. The walker is fully ope when you hear the 3rd click.

2. To close: Hold the front of the walker and at the same time, turn and pull the locking mechanism forward and lower the upper part of the walker all the way down.

3. To adjust the height: The simplest method to adjust the height is to lower the upper part of the walker all the way down (as above, in step 2) then pull the upper part of the walker back up so that it clicks into one of the three height positions.
   WARNING!
   NEVER adjust the height when your child is in the walker. DO NOT place your child in until you have adjusted the height and locked the height adjustment lock.
   Attaching the walker’s front wheels

4. With the baby walker upside down and fully folded down, insert the two front wheels into each round hole on either corner at the front of the walker.
   Tip: Use the provided wheel pusher tool to press the wheels in (tap the back of the wheel pusher lightly with a hammer if required)
   Attaching the walker’s rear wheels

5. Insert the two rear wheels into each round hole on either corner at the rear of the walker, ensuring the small plastic block (A) is seated in its hole.
   Tip: Use the provided wheel pusher tool to press the wheels in (tap the back of the wheel pusher lightly with a hammer if required)
   Attaching the walker’s anti-fall blocks

6. With the baby walker still upside down and fully folded down, place the anti-fall blocks around the walker as shown, inserting the two plastic stems on each block into the holes on the walker’s underside.
   ATTENTION! Ensure the narrow end of each block points to the corner of the walker.
   DO NOT USE THE WALKER WITHOUT THE ANTI-FALL BLOCKS ATTACHED
   Fitting the seat unit

7. Lower the walker all the way down, place the walker on a flat level surface then place the seat unit in to the centre of the baby walker.

8. Attach all plastic connectors on the seat unit to the walker body in the following order:

   • Starting with the seat unit’s armrest insert pins into keyhole slots (A1) and (A2), by pushing the pin into the larger end of the keyhole, then slide the shaft of the pin into the smaller end of the keyhole until it clicks in place (see Fig 1).

   • Then attach the seat unit backrest by pushing the plastic clips (B1), (B2), (B3), and (B4) into the holes. Start from one side and work your way around. Grip the back of the seat unit as low down and close to the plastic clip as possible (see Fig 2) and ensuring the clip is lined up with its hole, push the clip in.
     If a clip is not protruding from the seat unit you may need to locate it and pull it through the hole in the seat cover.

   • Finally insert the pins at the front of the seat unit into keyhole slots (C1), (C2) and (C3). (see Fig 3)
     Warning: ensure all pins and clips are properly attached before placing your child in the seat.
     The footpad

9. The footpad must be fitted in the rocker mode, and when you don’t want your child to move about in the walker mode. Attach using the six clips on the footpad and hook over the sidebars on either side of the base.
   Attaching the Flexi-toys
   WARNING: Assembly by an adult.

10. Add three of the toy rings to one flexi-toy and slot the flexi-toys into the holes provided on either side of the main body of the walker.
    Note: The Flexi-toys shown may vary from those included with the product.
    Using walker and rocker modes

11. Grip the sliding blocks at the front of the walker on the walker base and move them in opposite directions as shown.

12. Separate the blocks and repeat the procedure on the rear of the walker.

13. Whilst pressing the buttons (A) at each end of the walker base, rotate the base upwards 90 degrees and release the buttons. Check the base is locked and repeat the process on the opposite side.
    To convert the rocker back to a walker, simply reverse steps 11 to 13.
    Press button (A), turn the base back down, close the end blocks together and reconnect.
    WARNING! DO NOT convert from rocker to walker or vice-versa whilst your child is seated in the walker. Musical play tray

14. Using a Phillips screwdriver, unscrew the battery cover on the underside of the musical play tray.
    Insert 2 x 1.5V AA batteries (not supplied) ensuring the correct battery orientation is observed and then reattach the cover, replacing the screw, making certain it is not over-tightened.
    Top Tip:

15. Some brands of batteries will have slightly different lengths than others.
    If you find the musical play tray is not working with fresh batteries then this may be because the positive terminal is not making proper contact. To rectify this, first re-insert the batteries if this does not work, try a different brand. Finally, if the play tray still fails to work, please contact MyChild customer service.

16. On the underside of the musical play tray, you will find a holding strap that can be used to attach the toy to your child’s cot or pushchair. Wrap the strap around a solid fixing point (e.g. the cot side or the pushchair’s bumper bar) and insert tab (A) into the keyhole slot (B). To attach to the walker use suckers (C) and place them in the recess on the front of the walker.

Care and maintenance

• To prolong the life of your nursery product keep it clean and do not leave it in direct sunlight for extended periods of time.
• Removable fabric covers and trims may be cleaned using warm water with household soap or a mild detergent. Allow it to dry fully, preferably away from direct sunlight.
• If the wheels squeak – use a silicon-based spray ensuring it penetrates the wheel and axle assembly.
• Do not dry clean, or use bleach.
• Do not machine wash, tumble or spin dry, unless the care labeling on the product permits these methods.
• Non-removable fabric covers and trims may be cleaned using a damp sponge with soap or mild detergent. Allow it to dry completely before folding or storing it away.
• In some climates, the covers and trims may be affected by mould and mildew. To help prevent this from occurring, do not fold or store the product if it is damp or wet. Always store the product in a well-ventilated area.
• Always check parts regularly for tightness of screws, nuts, and other fasteners -tighten if required. To maintain the safety of your nursery product, seek prompt repairs for bent, torn, worn, or broken parts.

www.mychild.co.uk

Customerservice@kooltrade.co.uk Imported by Kooltrade Ltd. M34 3QA Tel: 0161 335 2508.

References

• My Child store – My Child Store
• Warranty – My Child Store

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>