blink HQ 200 Smart Home Level 2 EV Charging

© 2022 by Blink Charging Co. Its Affiliates and Subsidiaries (“Blink”)
No part of the contents of this document may be reproduced or transmitted in any form or by any means without the express written permission of Blink. The contents of this document have been verified by the manufacturer to be consistent with the described components; however, inconsistencies sometimes occur. Such inconsistencies should be brought to the attention of a Blink representative. Changes to this manual may be made at any time without notice.

Disclaimer of Consequential Damages
Blink is not responsible for the use or application by any person of the materials in this manual. Blink is not responsible for damages, either direct or consequential, arising out of or relating to the use or application of these materials.

Certain sections of this manual are meant as a guide for professional electricians. The manual contains general guidelines and may not provide instructions for your specific situation. Do not attempt installation if you lack the knowledge and understanding required for the installation, otherwise, personal injury and/or death as well as property damage or loss could occur.

Electricity is dangerous and can cause personal injury or death as well as other property loss or damage if not used or constructed properly. If you have any doubts whatsoever about performing the installation of the equipment, please do the smart thing and hire a licensed electrician to perform the work for you. Never work with live voltage. Always disconnect the power source before working with electrical circuits. When performing the installation, please read and follow this manual. Additionally, always follow your local electrical code and requirements which are specific to local areas.

Notice
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Blink, Blink Network, and the Blink logo are registered trademarks of Blink.
SAE J1772™ is a trademark of SAE International®

Blink
2404 W. 14th St.
Tempe, AZ 85281
(888) 998 2546
www.BlinkCharging.com
BlinkCharging.com  (888) 998 2546.

IMPORTANT SAFETY INSTRUCTIONS

Before installing or using the Blink Electric Vehicle Supply Equipment (EVSE), read all these instructions, paying particular attention to any WARNING and CAUTION markings in this document and on the Blink Product. You should also review any instructions included with your electric vehicle (EV) as they pertain to vehicle charging. The following symbols and associated instructions are used throughout this document and relate to actions necessary to avoid hazards.

Safety Instructions

Legend

• WARNING Used when there is a risk of personal injury
• WARNING: RISK OF ELECTRIC SHOCK Used when there is a risk of electric shock
• WARNING: RISK OF FIRE Used when there is a risk of fire
• CAUTION Used when there is a risk of damage to the equipment
• This product should be installed only by a qualified approved technician.
• Blink is not responsible for physical injury, damage to property or equipment caused by the installation of this device.
• A device employing pressure terminal connectors for field wiring connections shall be provided with instructions specifying a range of values or a nominal value of tightening torque to be applied to the clamping screws of the terminal connectors.
• Make sure that the materials used, and the installation procedures follow local building codes and safety standards.
• The information provided in this manual in no way exempts the user from the responsibility to follow all applicable codes or safety standards.
• Review this manual carefully and consult with a licensed contractor, licensed electrician, or trained installation expert to make sure of compliance with local building codes and safety standards.

Repair and Maintenance Clause

• Only a licensed contractor, licensed electrician, or trained installation expert is allowed to repair or maintain this device. It is forbidden for a general user to repair or maintain this device.
• Any repair or maintenance MUST be performed after removing power from this device.

Moving and Storage Instructions

• Store the product at a temperature between -40 and +80 °C.
• Check product for damage after moving.
• Carry the product by the sides. Do not lift or carry by either the flexible cord or the EV cable, if provided.

FCC Rules and Industry Canada License-Exempt RSS Standard(s)

• This device complies with Part 15 of the FCC Rules. Changes or modifications are not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
• This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

WARNING: RISK OF ELECTRIC SHOCK
Basic precautions should always be followed when using electrical products, including the following:

• Read all the instructions before using this product.
• This device should be supervised when used around children.
• Do not put your fingers into the EV connector.
• Do not use this product if the flexible power cord or EV cable is frayed, has broken insulation, or has any other signs of damage.
• Do not use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage.

WARNING: RISK OF ELECTRIC SHOCK
Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded.

WARNING: RISK OF ELECTRIC SHOCK

• Do not touch live electrical parts.

• Incorrect connections may cause electric shock.

• WARNING
  This equipment is intended only for charging vehicles that do not require ventilation during charging. Please refer to your vehicle’s owner’s manual to determine ventilation requirements.

• WARNING
  Do not use extender cables to increase the length of the charging cable. The maximum length is limited to 25 feet by the National Fire Protection Agency.

• CAUTION
  To reduce the risk of fire, connect only to a circuit provided with Model HQW2-50C-W1-N1-N-23, HQW2-50C-N1-N1-N-23, HQW2-50C-W1-N2-N-23-D for 50 A; Model MQW2-50C-M2-R1-N-23, HQW2-50C-W1-N1-N-23, HQW2-50C-N1-N1-N-23, MQW2-50C-M2-R2-N-23-D, HQW2-50C-W1-N2-N-23-D for 62.5 A amperes maximum branch circuit overcurrent protection in accordance with the National Electrical Code, ANSI/NFPA 70 and the Canadian Electrical Code, Part I, C22.1.

General Conventions
The use of the word “Note:” indicates additional information that is relevant to the current process or procedure.

INTRODUCTION

This INSTALLATION MANUAL describes how to properly install the Blink HQ 200 – Level 2 AC EVSE (Blink Product). Contact the Blink Support Center at (888) 998 2546 for troubleshooting assistance and additional technical questions. Unauthorized modification to the Blink product will void the manufacturer’s warranty. The Blink Product specified in this document is designed for the North American market to charge plug-in electric vehicles (PEVs), plug-in hybrid electric vehicles (PHEVs), and battery electric vehicles (BEVs). It provides

Level 2 AC charging shortens the charging time for typical EVs when compared to a Level 1 AC EVSE.

PRODUCT OVERVIEW

PRODUCT SPECIFICATIONS

Output Power

| NEMA 14-50P: 2.9, 3.8, 5.8, 7.7. 9.6 kW

Hardwired: 2.9, 3.8, 5.8, 7.7, 9.6, 11.5, 12 kW

Output Amperage| NEMA 14-50P: 12, 16, 24, 32, 40 A

Hardwired: 12, 16, 24, 32, 40, 48, 50 A

Circuit Breaker Options| NEMA 14-50P: 15, 20, 30, 40, 50 A

Hardwired: 15, 20, 30, 40, 50, 60, 70 A

Voltage| 208/240 VAC
Voltage Range| 180 to 264 VAC
Frequency| 50, 60 Hz
Input Wiring Type| NEMA 14-50P (Default) Hardwired (Optional)
Input Wiring Scheme| L1, L2, PE
Cold-Load Pickup| The randomized delay is between 120 and 720 sec. before the charge resumes after a power failure.
Power Measurement Accuracy| Embedded meter with a ±1% accuracy at the nominal input.
Surge Protection| Up to 6 kV at 3,000 A
FUNCTIONAL SPECIFICATIONS
Charge Connector Type| SAE J1772, Lockable (up to 0.24” or 5mm Shackle Diameter)
Charge Cable Length| 23ft. (7.01m)
Demand Response| No| Yes
Status Indicator| Status LED| Status & WLAN LEDs, Audio
User Interface| None| Mobile Application
Access Control| None
Local Load Management| None| Client
NETWORK SPECIFICATIONS
Wireless Local Area Network (LAN)| None| 2.4 and 5 GHz Wi-Fi (802.11 b/g/n/ac)
Wide Area Network (WAN)| None
SAFETY & COMPLIANCE SPECIFICATIONS
Ground Fault Detection| CCID20, 20 mA per UL 2231, Automatic Reset Feature and Manual Reset Feature
Ground Monitor| Ground Monitor per UL 2231
Safety Compliance| UL and cUL, NEC Article 625, RoHS
Protection| Over-Voltage (OVP), Under-Voltage (UVP), Over-Current (OCP), Over- Temperature (OTP), and Short-Circuit Protection
EMC Compliance| FCC Part 15B, Industry Canada (IC)| FCC Part 15B, Industry Canada (IC), Norma Oficial Mexicana (NOM)
ADA Compliance| Yes
ENERGY STAR Certified| Yes
OPERATIONAL SPECIFICATIONS
Mounting Type| Wall Mount
Enclosure Rating| NEMA Type 3R Indoor/Outdoor
Operating Temperature| Up to 40 A: -30°C to +50°C (-22°F to +122°F), At 50A: -30°C to +45°C (-22°F to +113°F)
Storage Temperature| -40°C to +80°C (-40°F to +176°F)
Operating Humidity| 5 to 95 % Relative Humidity, Non-Condensing
Charger Dimensions| 11.65”H × 8.91”W × 4.02”D (296mm H x 226.2mm W x 102.2mm D)
Package Dimensions| 18.15”H x 14.80”W x 11.42”D (461mm H x 376mm W x 290mm D)
Charger Weight (Unpackaged)| 20.94lbs. (9.5kg)
Charger Weight (Packaged)| 23.15lbs. (10.5kg)

PRE-INSTALLATION INSTRUCTIONS

Safety and Grounding

CAUTION:
DISCONNECT ELECTRICAL POWER PRIOR TO INSTALLING THE BLINK CHARGING STATION. FAILURE TO DO SO MAY CAUSE PHYSICAL INJURY OR DAMAGE TO THE ELECTRICAL SYSTEM AND BLINK PRODUCT.

The Blink Product should be installed only by a licensed contractor, and/or a licensed electrician in accordance with all applicable state, local and national electrical codes and standards. Before installing the Blink Product, review this manual carefully and consult with a licensed contractor, licensed electrician and trained installation expert to ensure compliance with local building practices, climate conditions, safety standards, and state and local codes.

Use appropriate protection when connecting to the main power distribution cable. Use tools as outlined in the “Tools Required for Installation” section.

Grounding Instructions
This product must be connected to a grounded, metal, permanent wiring system; and an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product.

INSTALLATION INSTRUCTIONS

Tools Required for Installation

Tools

Security Torx T20 Driver
Wire Cutters
Wire Strippers
Torque Wrench
Drill
Drill Bits
Slotted Screwdriver
P3 Phillips Screwdriver
Heat Shrink Tube

Parts Required for Installation

Wire Size and Temperature

Product Installation

• STEP 1: Remove the front cover screws

• STEP 2: Remove the front cover

• STEP 3: Remove the installation cover screws

• STEP 4: Remove the installation cover

• STEP 5: Set maximum current by configuring the DIP switch using the following table
  WARNING: Power must remain off before changing the DIP switch.

• STEP 6: Secure the main body mounting bracket to the wall with appropriate screws.
  Follow applicable accessibility requirements for the mounting position. The unit shall be stored or located at a sufficient height above the floor. For an indoor site, it should be not lower than 18” (450 mm) and not higher than 4” (1.2m). For an outdoor site, it should be not lower than 24” (600 mm) and not higher than 4” (1.2m). Refer to Article 625, NEC.
  The mounting bracket has six screw holes for wall mounting. If only two screws are used for mounting, the screws should pass through the middle two screw holes of the mounting bracket. The other screw holes are reserved for the user.

  • For masonry walls, use M6 mechanical screws (commercially available).
  • For finished walls supported by wood studs, use #12 self-tapping screws.
  • Please refer to the following torque. The actual torque is according to the wall material.
    Screw| Torque
    ---|---
    M6| 25 kgf.cm min| 21.7 lb.-in min

    12| 25 kgf.cm min| 21.7 lb.-in min

• STEP 7: Hang the product on the mounting bracket
• STEP 8: Slide down the product to rest on the bottom flange
• STEP 9: Install the locking screws (M4 Torx)
• STEP 10: Reassemble the install cover and front cover with M4 screws

Charging Status Indicators

BlinkCharging.com • (888) 998 2546.

Blink, Blink Network, and the Blink logo are registered trademarks of Blink.
SAE J1772™ is a trademark of SAE International®

Blink
2404 W. 14th St.
Tempe, AZ 85281
(888) 998 2546
www.BlinkCharging.com.

References

• Blink Charging: Electric Vehicle (EV) Charging Stations (EVSE)
• kgf.cm
• Blink Charging: Electric Vehicle (EV) Charging Stations (EVSE)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>